Knock and Ultimate

StonesKid

New member
Got this off of http://members.home.net/unskarred/3_bar_chip_information.htm, could this be the reason why some of us have knock. What if I change to T2 or T3? I am going to toss this thing if this is the case

"Timing

A bit ago, someone expressed concern that our chip had more aggressive timing than stock in our T1 level chip. I made that program to be as close to stock as possible, but seeing as there are multiple timing tables, it may not be exactly close to stock. If you are having issues that you think are related to our chip having too much timing in the T1 level, it can't be by more than 1-3 degrees (in my opinion), so just reset your timing with a timing gun to a few degrees retarded. I've seen trucks run great in this configuration."



_________________
2001 Silver Grand Prix GTP
2000 Red Corvette FRC
1993 White GMC Typhoon

<font size=-1>[ This Message was edited by: StonesKid on 2001-11-10 10:40 ]</font>
 

JimmyM

Banned
I doubt that it's your Ultimate.I have one of BG's 50# chips,and have seen exactly .5 degrees of KR. Once.

_________________
reader21.jpg

13.05 @ 103 1.79 60' with a worn out trans.

<font size=-1>[ This Message was edited by: Jimmy on 2001-11-10 11:08 ]</font>
 

bdubb

I am teh kingpin!
i've seen trucks run 20degrees of timming and no problems, and even a truck with 35degrees. sounds like you have other issues.
 

smeagol

Active member
Our programming requires your truck to be running damn good before you can really make gains. I am always prescribing some remedies to trucks, and I usually find that the ones that DO have the serious knock issues haven't performed these.

-Fuel filter
-new PCV valves
-top engine cleaner
-fresh plugs
-good cap&rotor
-fresh wires

I also just go over basic Syty mods; 160 thermostat, the small intercooler mods (3/4" hose & hotwired pump). If you still have a knock problem at this point, you need to verify TDC, to be sure your timing is accurate (this should really be done earlier). If still knocking, see if high octane fuel eliminates the knock, to verify it is not false knock.

Brian G
STG
 

StonesKid

New member
Thanks for the tips, red. The truck had a full tune up a year ago (before I got it). Even though I have changed the cap/rotor, replaced the fuel filter, added dry gas, and check the timing.

Today I am going to replace the plugs, install 180 degree t-stat and hope and pray.

I do have an ATR aux instercoooler, is it necessary to hot wire the pump to run all the time? (Dont even know is the guy before me did either?)

what is TDC? What is the 3/4" hose you talk about (is this the reroute?)

Thanks for your help
 

Tooky

Serious about performance
On 2001-11-11 08:09, Red Canyonero wrote:
Our programming requires your truck to be running damn good before you can really make gains.
Once a given truck reaches this point, what gains are commonly seen?
-new PCV valves
-top engine cleaner
Interesting information, how and why do these items decrease potential for knock? How long would you suggest a PCV valve job should take? Thanks,
 

smeagol

Active member
Go with a 160 stat, first off. If you are running stock thermostat, that will cause you to knock cuz of high engine heat.

A year old tune up will mean a new tune up is needed probably. What wires are you using? What cap& rotor? What plugs, and what gap? These are the most important issues IMO.

The top engine cleaner helps remove carbon deposits in the intake tract & chamber, which means removing hot spots & causes of detonation. This helps tremendously. Fresh PCV's mean no oil & junk routed thru the chambers/intake. Take ya about 10 minutes to change, with 9 of those minutes dedicated to removing the intercooler to get at the PCV's.

Gains seen on a well prepped truck.. see my page, or the old post by Steve Proudlock with the dyno results the Washington guys had. Most track numbers I see are race gas situations, with Sy's at mid 12s or so, Ty's at high 12s. Pump gas... high 12s for Sy's, low 13s for Ty's.

Hoping and praying won't get you anywhere with these trucks. Greasy hands and bloody knuckles is where it's at...

BG
 

smeagol

Active member
Go with a 160 stat, first off. If you are running stock thermostat, that will cause you to knock cuz of high engine heat.

A year old tune up will mean a new tune up is needed probably. What wires are you using? What cap& rotor? What plugs, and what gap? These are the most important issues IMO.

The top engine cleaner helps remove carbon deposits in the intake tract & chamber, which means removing hot spots & causes of detonation. This helps tremendously. Fresh PCV's mean no oil & junk routed thru the chambers/intake. Take ya about 10 minutes to change, with 9 of those minutes dedicated to removing the intercooler to get at the PCV's.

Gains seen on a well prepped truck.. see my page, or the old post by Steve Proudlock with the dyno results the Washington guys had. Most track numbers I see are race gas situations, with Sy's at mid 12s or so, Ty's at high 12s. Pump gas... high 12s for Sy's, low 13s for Ty's.

Hoping and praying won't get you anywhere with these trucks. Greasy hands and bloody knuckles is where it's at...

BG
 

bdubb

I am teh kingpin!
On 2001-11-11 19:48, Red Canyonero wrote:
Go with a 160 stat, first off. If you are running stock thermostat, that will cause you to knock cuz of high engine heat.

A year old tune up will mean a new tune up is needed probably. What wires are you using? What cap& rotor? What plugs, and what gap? These are the most important issues IMO.

The top engine cleaner helps remove carbon deposits in the intake tract & chamber, which means removing hot spots & causes of detonation. This helps tremendously. Fresh PCV's mean no oil & junk routed thru the chambers/intake. Take ya about 10 minutes to change, with 9 of those minutes dedicated to removing the intercooler to get at the PCV's.

Gains seen on a well prepped truck.. see my page, or the old post by Steve Proudlock with the dyno results the Washington guys had. Most track numbers I see are race gas situations, with Sy's at mid 12s or so, Ty's at high 12s. Pump gas... high 12s for Sy's, low 13s for Ty's.

Hoping and praying won't get you anywhere with these trucks. Greasy hands and bloody knuckles is where it's at...

BG

sell out.
 

StonesKid

New member
Brian, thanks for the reply. I installed the 180 this afternoon. Knock seems to have been reduced, but still there floating around 4-7 degrees. I have KB Red Hot a(year old 1k miles) wires and a Accel cap/rotor (new last week). I did not have time to change the plugs today, but I will be doing that next weekend. I will also try to get some carbon remover. After I try the above I think I would have exhusted all my options. And I do have some bloody knuckles and have used a lot of curse words.

One thing I can say is that I have been working on this truck tweeking it with the DM for about a month. Everytime I am done I do see some gains and the truck feels stronger and faster.

Thanks For All Your Help Everyone
 

Tooky

Serious about performance
On 2001-11-11 19:47, Red Canyonero wrote:
Go with a 160 stat, first off. If you are running stock thermostat, that will cause you to knock cuz of high engine heat.
I agree and I have a 160 stat. But if what you said is true, how would you say the stock trucks performed off the lot in 1991? Do you think they knock retarded a few degrees? I wish someone had that information but I imagine scan tools like Datamaster weren't available till much later and the people who have used TECH1 seem rather few and far between.
The top engine cleaner helps remove carbon deposits in the intake tract & chamber, which means removing hot spots & causes of detonation. This helps tremendously.
Awesome, I want to get this stuff. I saw it tonight, it is in a silver can with blue labels. What is the procedure to using it? The instructions seem to reference carburetors and A.I.R. systems which I know nothing about.
Fresh PCV's mean no oil & junk routed thru the chambers/intake. Take ya about 10 minutes to change, with 9 of those minutes dedicated to removing the intercooler to get at the PCV's.
I am picking up 3 of these tomorrow. #8995910 seems like the ones to get HOWEVER the 91 Service Manual says 8995909 and some SyTy sites/posts say 8995911?? WTF? And my emissions sticker under the hood says there are 3 PCV valves, 2 on pass side and the one on the driver's side that connects to the stock airbox. Is or isn't that a PCV valve? I read very little reference to that and some posts said "THERE ARE ONLY TWO, BOTH ON PASSENGER SIDE".?
Hoping and praying won't get you anywhere with these trucks. Greasy hands and bloody knuckles is where it's at...
LOL! I could not have said it better myself!!!
 

Tooky

Serious about performance
On 2001-11-11 21:38, StonesKid wrote:
One thing I can say is that I have been working on this truck tweeking it with the DM for about a month. Everytime I am done I do see some gains and the truck feels stronger and faster.
I have noticed the same thing. Thanks everyone.
 

Falco

Donating Member
Josh,

There are only two on the passenger side and none on the driver side. However I can't recall the PN.

Falco
Sy #2613
 

V

Donating Member
On 2001-11-11 22:33, TookyCat wrote:
I am picking up 3 of these tomorrow. #8995910 seems like the ones to get HOWEVER the 91 Service Manual says 8995909 and some SyTy sites/posts say 8995911?? WTF?

As far as I know, 8995910 is the dealer listed part for SyTys. Look for the letter "E" on the bottom. I could not find the "09" or the "11" online. I wonder if these are still valid part numbers. Maybe you can check this out for us?
 

GM TURBO

Sell Out
There are some who will argue - which is fine because I did to before I knew better - the Accel C&R SUCKS!!! It prolly lasted 2 months on my truck before it became severely pitted. The one that had been on for 2 years prior was in better condition. I had a pretty decent amount of knock with it on - changed and it decreased. Now, if I could just get my truck back so I could install my new fuel pump.
 

kwick6

Donating Member
The top engine cleaner should be added to a FAQ somewhere.
It is available at most GM dealerships. I called a local GM dealer it was $6.18 a can. Part # 1050002.
It will take roughly 2.5 hours to do.
You will need a short piece of silicone vacuum line (the smallest internal diameter) 4mm sound right? Then take the red *straw* off of a can of WD40. Use a 3" piece of that straw and shove it in the end of the vacuum hose. Make sure it is in real tight.
Push it in the vacuum hose until about a 1/2" is sticking out. This is what you will use to draw the Top engine cleaner out of the can. With the engine running, remove the brake booster, the thing you change when yer truck sounds like a duck. :grin: Once you take that plastic piece off, put a funnel in the end of it. Its best you figure out what funnel will fit that before you start all this. Put the end of the funnel on the hose, and then put the end of the silicone hose without the straw tip in the funnel. You will want to have opened the can of top engine cleaner to puncture the metal cap so when you are ready to begin, it is just a matter of unscrewing the cap. The idea here is to draw very slowly, with the plastic straw end. It will make the engine stall if you just submerge it, so just hold the end of the hose so it sucks small amounts of cleaner out. You will see what I mean about going slowly. Once you get down to about 1/3 of a can left take the hose setup and set it aside. Holding the funnel in one hand take the remaining top engine cleaner and dump it in the funnel. You will want to stall the engine out. So dump it fast. Then you can hook up the brake booster, and get it put back together.
Let it sit for about 2 hours. Then start it up. It will be difficult to start. Then once it starts up, you will see lots of white smoke pour out the exhaust. So you may want to think of a place to do this, that you won't disturb any neighbors :razz:. It is a lot of smoke, you'll laugh once you do this. Get on the throttle a couple times and rev it to get the cleaner to burn out. The smoke should go away in about 5-10 minutes. That is about it. It is important that you do an oil change immediately. I usually don't drive much more than 10 miles after I do the top engine cleaner, before I do an oil change. I hope I haven't left anything out. I would be happy to explain this better to anyone, if its unclear. Let me know.

Scott
 

Tooky

Serious about performance
Thanks for your excellent instructions. A few questions. How important is it to create a seal inside the funnel with the vacuum hose? If I run my truck with the AFPR line open, it will virtually stall and die. Wouldn't the same thing happen if I have a big hole in the middle of the funnel? Also you say to dump the last 1/3 of the can into the funnel so the motor stalls. What do you do with the rest once the motor has stalled? Do you just dump it all in regardless? Or does it suck up that last 1/3 at a very fast rate?
Finally how come you suggest 2 hrs soak time while other places have said 15 or 30 minutes? And what difference will/might I notice once this is all done, I mean what specifically should I look for? Thanks.
 

Tooky

Serious about performance
On 2001-11-12 04:08, Falco wrote:
Josh,

There are only two on the passenger side and none on the driver side. However I can't recall the PN.
Falco, why does my black/white emissions sticker under the hood say there is a PCV valve on the driver's side? What goes there between the black hose and the valve cover then if it is not another PCV valve? Thanks.
 
Top