Looking for help with a DM file

Sean Krupa

Moderator
Re: Looking for help with a DM file

IDK why your graph looks so funky, but here is what yours should look like. This is with Alky also.
8-27-11.jpg
 

sytyguy

Moderated User
Re: Looking for help with a DM file

Glad you got everything dialed in Sean.....good for you.

Note a major difference in your two graphs: IAT temps. 88 degF vs 170 degF is a BIG difference.

Raman117, I would set your DM up to look like Sean's (like I've recommended already). See how much easier it is to see a pattern when the TPS, retard, and boost are all charted?
 

raman117

Member
Re: Looking for help with a DM file

Glad you got everything dialed in Sean.....good for you.

Note a major difference in your two graphs: IAT temps. 88 degF vs 170 degF is a BIG difference.

Raman117, I would set your DM up to look like Sean's (like I've recommended already). See how much easier it is to see a pattern when the TPS, retard, and boost are all charted?

Agreed, his chart is much more useful. I fixed my intake temps, but I'm still only getting 8lbs of boost max (I have *not* bypassed the solenoid at all). I know there is some KR, but for the purpose of figuring out my low boost, let's ignore that. I am 99% sure that if I run a tank of race gas the KR will disappear.

Here's my latest run (I neglected to include TPS %):


http://www.mediafire.com/file/p9agc9l7dc57zz0/8-28a.uni

bNqmy.png
 

WyoSyclone

Active member
Re: Looking for help with a DM file

I just looked... you're actually running around 12.5 lbs of boost. Remember to set DM to read 2-3 bar map, under 'setup', 'display preferences'. Your boost is very slow to build. You should probably check your wastegate rod adjustment.

Intake air temps are good, voltage is good. It's running leaner than what I would like to see.

EDIT.. I usual set my chart up in the lower right with "rpm, boost, afr, KR". If I'm looking to see why boost is screwy I change the KR to WGDC.

HTH
 

raman117

Member
Re: Looking for help with a DM file

I just looked... you're actually running around 12.5 lbs of boost. Remember to set DM to read 2-3 bar map, under 'setup', 'display preferences'. Your boost is very slow to build. You should probably check your wastegate rod adjustment.

Intake air temps are good, voltage is good. It's running leaner than what I would like to see.

EDIT.. I usual set my chart up in the lower right with "rpm, boost, afr, KR". If I'm looking to see why boost is screwy I change the KR to WGDC.

HTH

Just so I am on the same page, even though I'm running a stock chip with a 2-bar MAP, I should still set DM for 3-bar MAP? Any hints on why it's running so lean? I'm still trying to find a fuel pressure tester with a long enough hose to reach the windshield, so I can read it while driving.
 

raman117

Member
Re: Looking for help with a DM file

After doing a few more runs, I noticed my IAT's increasing. Come to find out my IC pump wasn't working, so I am now looking for a replacement pump. Ugh, there's always something!
 

raman117

Member
Re: Looking for help with a DM file

Ok, I purchased a new pump and got my IAT's under control. However, there is definitely something wrong with either the aftermarket chip, 3-bar MAP, or alky.

Here is a link to my stock setup (2-bar MAP, no alky, stock chip):

http://www.mediafire.com/file/3axanadijtlmo21/9-1k.uni

Xiaac.png



And here is a link to the upgraded setup (3-bar MAP, alky, burned chip):

http://www.mediafire.com/file/d7zxrdk7f6duo8w/9-1i.uni

dEatA.png




The vehicle just falls flat on it's face with the mods. It's very odd that it's pushing 23lbs of boost with the *stock* chip, and barely 12lbs on the aftermarket chip.
 

sytyguy

Moderated User
Re: Looking for help with a DM file

It's not pushing 23 psi with the stock chip.....you have 3bar calibration selected in DM on the 2bar run. Gotta remember to set that accordingly. Want to run a stock chip? Change chip, MAP, and DM setting. 3bar? Change chip, MAP, and DM setting.

Make sure you go WOT on your runs too. I'm not near DM to see the run, but the screenshot on the 3bar run shows 95.7% throttle.

If you track it down to the tune, I've got a reburn with your name on it.
 

raman117

Member
Re: Looking for help with a DM file

It's not pushing 23 psi with the stock chip.....you have 3bar calibration selected in DM on the 2bar run. Gotta remember to set that accordingly. Want to run a stock chip? Change chip, MAP, and DM setting. 3bar? Change chip, MAP, and DM setting.

Make sure you go WOT on your runs too. I'm not near DM to see the run, but the screenshot on the 3bar run shows 95.7% throttle.

If you track it down to the tune, I've got a reburn with your name on it.

Aha, thanks for the tip! I'll check that out tomorrow.
 

raman117

Member
Re: Looking for help with a DM file

I just did a run with the MAP option set correctly (thanks Hood). I'm seeing a lot of KR, but again I'm fairly certain it's due to the horrible gas we have up here, as last year I ran a tank of race gas and had zero knock. However, that still doesn't explain why the modded chip, alky, and 3-bar MAP runs so poorly. Mike, do you mind if I overnight you the chip to reburn? I'm not convinced it's bad, but I'd like to rule it out anyway.

Here's the file:

http://www.mediafire.com/file/5hoqxc5g5c5618m/9-2a.uni

1STF3.png
 

sytyguy

Moderated User
Re: Looking for help with a DM file

Go a local SyTyer? Let them try the chip and see how it does in their truck. That will rule out a bad burn.
 

raman117

Member
Re: Looking for help with a DM file

I'm up in no mans land, unfortunately. Dig is probably the closest, and lives like 250 miles away. I'm scheduled to go to the track next weekend, so I was hoping to get this all buttoned up early next week if possible. Would you be around tomorrow if I were to ship it overnight Saturday delivery?
 

sytyguy

Moderated User
Re: Looking for help with a DM file

Heading out of town in 20 minutes and won't be back until Tuesday. Send it on if you want, but that's when I get back.
 

raman117

Member
Re: Looking for help with a DM file

What was your alky set to during these runs?

Oops, sorry for the delay in responding, I didn't see this question. My alky was set between 6 and 7. I made another run with a reburned chip from Hood, 3bar MAP, alky, and race fuel.....something still doesn't seem right. The tach is still fluttering, and the engine seems to hit several flat spots during acceleration. I'm not convinced it's a chip problem, but rather something else I'm missing. Here's the file and an SS:

http://www.mediafire.com/file/1ngqjnrjdqzev7w/9-10c.uni

CoIko.png
 

Sean Krupa

Moderator
Re: Looking for help with a DM file

I would try lowering the Alky down to 4-5. I raised mine to 6 once and felt it bog from too much Alky. Are you running 100% or 50/50 meth? Also what do you have your Spark plug gap at?

Alky and race gas seems like a lot of octane. I would almost bet by lowering the Alky to 4-5 will solve your problem. Also try running just pump gas. Just watch your KR.

Also, change the graph to where I had mine- RPM-TPS-Boost-KR

HTH
 

raman117

Member
Re: Looking for help with a DM file

I would try lowering the Alky down to 4-5. I raised mine to 6 once and felt it bog from too much Alky. Are you running 100% or 50/50 meth? Also what do you have your Spark plug gap at?

Alky and race gas seems like a lot of octane. I would almost bet by lowering the Alky to 4-5 will solve your problem. Also try running just pump gas. Just watch your KR.

Also, change the graph to where I had mine- RPM-TPS-Boost-KR

HTH

When I adjust the alky to less than 6 and hit the test button, the light never goes green (which I believe means it isn't being injected?) I'm running 100% HEET out of the yellow bottle. Spark plugs are set at .028. I've tried it with pump gas with the same effect. When I do some runs tonight, I'll adjust the graph to where yours was.
 

Vaders Sy

Donating Member
Re: Looking for help with a DM file

Spark plugs are set at .028.

Correct me if I'm wrong, but the Syclone service manual supplement shows spark plug gap at .045. You are using CR42TS plugs?

Not sure if this causes any of your problems, but doesn't hurt to ask! Interesting read, I'm sure these guys will figure it out.
 
Top