Losing Datamaster connection at WOT

TYTILIDIE

METH HEAD
Almost never fails. I go full throttle and lose datamaster connection. Any of you guys had the same problem? I am using the MOates USB cable set to OPEN. Stock ECM, 65# motron injectors, 140 amp Power Master alternator, double checked grounds, MSD 6AL with noise filter. I am at a loss here. Not sure what to do. I am tuning this truck for a friend who has spent a lot of money on it and I can't really tune for boost if I can not log data.
 

bezerk

New member
Re: Losing Datamaster connection at WOT

i had it a few times also, what i did is make sure you are at 3-4K rpm and than floot it and hit full boost. it wouldn't loose conneion.

i stepped up to a different meth, and problem went away also.
 

WyoSyclone

Active member
Re: Losing Datamaster connection at WOT

Have you tried changing the latency settings on your com port?? I wonder if your voltage is dropping low enough that it affects communication on the ALDL?
 

TYTILIDIE

METH HEAD
Re: Losing Datamaster connection at WOT

Have you tried changing the latency settings on your com port?? I wonder if your voltage is dropping low enough that it affects communication on the ALDL?

Latency? Fill me in please. Voltage is not going below 13.6 at WOT. Of course, I suppose it is hard to say since I lose com. But, I tried doing some logging with TP5 and seem to have the same issue. Throughout the average run, I am seeing quite a few errors. Could I have a bad cable?
 

WyoSyclone

Active member
Re: Losing Datamaster connection at WOT

Latency? Fill me in please. Voltage is not going below 13.6 at WOT. Of course, I suppose it is hard to say since I lose com. But, I tried doing some logging with TP5 and seem to have the same issue. Throughout the average run, I am seeing quite a few errors. Could I have a bad cable?

Look at the DM help screen, but if I remember right it's 'right click' on computer icon, then 'device manager', then 'com ports'.... choose which com port DM is connecting through, then click on 'advanced settings'.... somewhere in there is a setting for 'latency'.... set it to what DM specifies....

... doing that cured my problems (I'm on Windows 98 on my tuning 'puter).

HTH :D
 

cloneman315

Active member
Re: Losing Datamaster connection at WOT

do the voltage mod,it should fix it.I posted it up a while back,as did erue as did jeff
 

ghettosled

SYTY SUPERSTORE
Re: Losing Datamaster connection at WOT

we seem to always have this problem and if you bypass the wiring to the aldl port and tap straight off the ECM it works flawless.
 

cloneman315

Active member
Re: Losing Datamaster connection at WOT

Aldl port voltage drops when the inj dc gets high,is what I have found.
 

TYTILIDIE

METH HEAD
Re: Losing Datamaster connection at WOT

Looks the ALDL "mod" is next. I get 14.1 volts at ECM now but still lose COM on WOT runs. Also still getting tons of errors. :roll: This is really getting old. If ALDL doesn't work I'm sending my cable back to Moates in case it is bad.
 

TYTILIDIE

METH HEAD
Re: Losing Datamaster connection at WOT

Look at the DM help screen, but if I remember right it's 'right click' on computer icon, then 'device manager', then 'com ports'.... choose which com port DM is connecting through, then click on 'advanced settings'.... somewhere in there is a setting for 'latency'.... set it to what DM specifies....

... doing that cured my problems (I'm on Windows 98 on my tuning 'puter).

HTH :D

Unfortunately I do not have a COM port on here. It is a newer lap top and uses all USB.
 

turbodig

Active member
Re: Losing Datamaster connection at WOT

we seem to always have this problem and if you bypass the wiring to the aldl port and tap straight off the ECM it works flawless.

x2... this was what I was going to suggest. I have an ALDL connector on a piece of 2-wire shielded cable that I use on troublesome trucks.
 

turbodig

Active member
Re: Losing Datamaster connection at WOT

Unfortunately I do not have a COM port on here. It is a newer lap top and uses all USB.

Yes you do... all USB cables/connectors emulate a COM port.
If you look in Device manager, one will be there when the cable is hooked up.
 

TYTILIDIE

METH HEAD
Re: Losing Datamaster connection at WOT

Yes you do... all USB cables/connectors emulate a COM port.
If you look in Device manager, one will be there when the cable is hooked up.

Been there done that, it isn't there. If it is it is called something else. I even did a "search" in windows.:lol:
 

TYTILIDIE

METH HEAD
Re: Losing Datamaster connection at WOT

we seem to always have this problem and if you bypass the wiring to the aldl port and tap straight off the ECM it works flawless.

Well I moved the ALDL port to the back of the ECM (about a foot away) and it wont log data when the truck is running. So KOEO it logs, KOER, it says no pcm sync recycling. I do a test com and it passes?

For the relocation of the aldl port, I cut all the wires and went in to a12, a9 and e12? Wired them right in to the aldl port.
 

TYTILIDIE

METH HEAD
Re: Losing Datamaster connection at WOT

So should I hook the other three wires back up? Any thoughts on why this would be happening?
 

Don W.

Stab it and steer it
Re: Losing Datamaster connection at WOT

I'll add one thing. I've got my adapter zip tied to the ALDL port. Seems to want to work loose. Also I've had -0- luck with changing latency. I use default with no issues. Go figure.
 
Top