Miss under boost FIXED

Don W.

Stab it and steer it
Did a bit of searching but this seems different. I have acquired a mis above about 10-12 pounds of boost. Hard to tell because I run out of road, but I can literally control it with the throttle.


Today I changed cap and rotor, idles better but mis didn't change one bit. I ohm’ed the wires. All but one were .71 - ,88, one was 1.00.

It’s obviously just the one cyl. Consistently the same every time. No randomness to the miss at all so I’m thinking it’s not the coil. Starts and idles just fine, runs fine up to about 10# boost coming in.


This seemed to start shortly, but not immediately, after I change the plugs. I’m gonna put the old plugs back in it tomorrow. And I'll pull the wires completely out of the truck and inspect them end-to-end.


So:

Hints appreciated of course, but my main question is how do I figure out what cylinder it is? That would help a bunch.


Thanks
 
Last edited:

dgoodhue

BuSTeD 4.3
Re: Mis under boost

Re: Mis under boost

The resistance is probably in KOhms. The wire with 1kohm's is probably number 1 due to the length.
 

Don W.

Stab it and steer it
Re: Mis under boost

Re: Mis under boost

The resistance is probably in KOhms. The wire with 1kohm's is probably number 1 due to the length.

Hmmm, your are correct!! So the next DAQ is am I OK or not? I've see a bunch of posts on who likes waht but no definitive answers. At least that I've seen. Thanks.

Regarding the dead cyl I was thinking I might make a blast down the street, do a quick shut down and try the laser thermometer on the ex manifold to see if one was lower than the others. Anybody think that would work? I just wonder if by the time I shut down, get out and raise the hood, everything will have pretty much equalized.:squint:
 

It's just a six

Super Member
Re: Miss under boost

Re: Miss under boost

Champion makes a spark plug cleaner tool.

It is a box where you insert your spark plug & press a button to shoot glass bead @ it to clean the plug.

After you clean the plug, you screw it into another portion of the box & hook up a plug wire to the plug.

Depress another button to give the spark plug some juice & watch the plug fire & while you are doing that, you can also add air pressure to the chamber & see if the spark goes away or is weak.

Not sure if they make a similar box for the automotive industry?

The one I am describing is for airplane spark plugs.

You might have a weak spark plug, just always remember, just because they are new spark plugs, does not mean they are good.:2cents:

Also, when you check for ohms on your plugs wires, move/bend the plug wires & see if the ohms change while your bending the wires.
 

atkonkler

Is this your bush?
Re: Miss under boost

Re: Miss under boost

Always inspect your plugs even if they are "new"! I've got "new" plugs installed them and had a running issue to later remove them all just to find one plug was cracked all the way around if you've ever worked at a parts store you know the Claude hoppers/ shade tree turkey neck mechanics you work with drop, toss and throw plugs when putting them into carts to be stocked on shelves I've witnessed it all first hand to later damage the plugs out because of their careless stupidity. Take them all out and inspect them all closely in a well lit room not a garage with poopy lighting and loose women hanging around to distract you! Haha oh and I forgot to also say there should be no partaking in beer drinking either. Haha like I always say there's only two reasons to drink ! One it's your birthday and two it's not!
 

sytyguy

Moderated User
Re: Miss under boost

Re: Miss under boost

What wires?

Measure overall length of wire (in inches) and measure resistance. Divide length by 12 and then divide overall resistance by the (new) length. That's your ohms per foot. Compare it to what the wires are rated for new. Most performance wires are in the 50-200 ohm/ft range.

Example: 31" wire measures 480 ohms. 31/12 = 2.58 & 480/2.58 = 186 ohms/ft.
 

Don W.

Stab it and steer it
Re: Miss under boost

Re: Miss under boost

Thanks on the "correct" wire info. And it wouldn't be the first bad plug I've ever had either.

Those plug cleaners, if they are still available for automotive plugs, were expensive. I've used the auto version back in the day.

All good points. I'll change the plugs back tomorrow. If that DOSEN'T work. I'll be back. Will let you know either way...

Appreciate it...
 

IpHoOnDyou

New member
Re: Miss under boost

Re: Miss under boost

Thanks on the "correct" wire info. And it wouldn't be the first bad plug I've ever had either.

Those plug cleaners, if they are still available for automotive plugs, were expensive. I've used the auto version back in the day.

All good points. I'll change the plugs back tomorrow. If that DOSEN'T work. I'll be back. Will let you know either way...

Appreciate it...

I had this issue once, an i felt like a dummy afterwards. When i swaped my plug wires over to the taylors truck ran like a champ. It idled better, an started better. When i do plug wires i always put a little dab of dialecteic greese in the plug boots for future ease of removal. I guess i must have put a little too much in one boot. Now when i first installed them i had made sure they all clicked down, but with heat an bumps in the road cly#4 poped off. Not completely tho, just enough to give me a miss right ubove 10psi. But the truck idled an started like nothing was wrong. Just a lil help from my head Don! Best of luck i hope its not serious
Steve
 

Don W.

Stab it and steer it
Re: Miss under boost

Re: Miss under boost

I had this issue once, an i felt like a dummy afterwards. When i swaped my plug wires over to the taylors truck ran like a champ. It idled better, an started better. When i do plug wires i always put a little dab of dialecteic greese in the plug boots for future ease of removal. I guess i must have put a little too much in one boot. Now when i first installed them i had made sure they all clicked down, but with heat an bumps in the road cly#4 poped off. Not completely tho, just enough to give me a miss right ubove 10psi. But the truck idled an started like nothing was wrong. Just a lil help from my head Don! Best of luck i hope its not serious
Steve

Don't ya hate it when that happens? I'm usually pretty, ah, careful about plug wires being on all the way. Always feel for that last little snap. I will definitely check things tomorrow. Thanks!
 

Syclone22

Member
Re: Miss under boost

Re: Miss under boost

After checking your ignition wires i would recommend
for boost above 12 psi an 0.030 inch gap on your plugs......
 

Don W.

Stab it and steer it
Re: Miss under boost

Re: Miss under boost

After checking your ignition wires i would recommend
for boost above 12 psi an 0.030 inch gap on your plugs......

Actually I'm running .25 which up to this has worked well. Since I'm pulling the plugs again today I'll double check that as well. Thanks.
 

Don W.

Stab it and steer it
Re: Miss under boost FIXED

In a word, wires. I pulled the Taylors, didn't see any flaws, but we know that doesn't mean much. Couldn't find any Taylors or MSD's. Bought Defphi. Marked USA Packard. As I recall back in the day Packard wires were very good. If looks have anything to do with it these are nice wires. Installed them routing and separating carefully. Worst part being where the wires snake between the DP and the head. JSM 3" DP doesn't leave a lot of room. Protected them here with hi-temp heat wrap. Test run - perfect. Miss is gone, power back.

Actually pulled fairly well on 5 cyls, just slower and sounded funny.:rotf:

Hope this little mess helps someone else. Otherwise I shuda stopped floating down that river in Egypt AKA de-nile and just changed them. Don't know but they have to be at least 5+ yrs old with countless passes down the 1/4.
 

Don W.

Stab it and steer it
Re: Miss under boost FIXED

Seems you're not alone Dave. Others have not good thing to say either. Considering that these are at least 5+ years old maybe I got the good set. Odd though. I've chatted with a couple racers at fairly big events and they swear by Taylors. Oh well, forward ho...
 
Top