monitoring datamaster pic

tydye

Banned
what do you see or think? only warmed up for 5 min using monitoer mode.
-
data.JPG
 
Last edited:

tydye

Banned
Re: monitoring datamaster pic

Updated DM image after tuneup

new....
Wires = 8mm Taylor
plugs = ur5
cap rotor = MSD copper
Ignition = MSD
Plugs gapped .032
-
-
data2.JPG
 
Last edited:

WyoSyclone

Active member
Re: monitoring datamaster pic

Updated DM image after tuneup

new....
Wires = 8mm Taylor
plugs = ur5
cap rotor = MSD copper
Ignition = MSD
-
-
data2.JPG

Intake temp is high - about 158 farenheit. It's idling a bit low. What is your idle vacuum in Hg?
 

tydye

Banned
Re: monitoring datamaster pic

It's usually been idling .700's and it does bounce slightly up and down. I did think the air charger felt it was running hot lately, think my pump is bad? It's hot wired currently

Also see the difference in my knock before tuneup? Seem normal?
 

WyoSyclone

Active member
Re: monitoring datamaster pic

It's usually been idling .700's and it does bounce slightly up and down. I did think the air charger felt it was running hot lately, think my pump is bad? It's hot wired currently

Also see the difference in my knock before tuneup? Seem normal?

Can't tell anything from the knock value from a screen shot.... would need the DM file to see any trends. If your knock count is bouncing around quite a bit at an idle you would want to check to see if the downpipe is hitting up against something, check to see if the fuel lines are banging against the firewall, and see if the motor is rocking around or not (bad motor mounts). The counts will climb when you first start it, then should stop counting up at an idle. Spark retard is the first thing you want to watch while driving.

When the motor cools down take the cap off of the upper IC, start the truck and see if you can see fluid circulating. If not, it could be a bad pump or an air pocket in one of the lines. Use the search button and you'll find lots of threads/remedies.
 

tydye

Banned
Re: monitoring datamaster pic

Can't tell anything from the knock value from a screen shot.... would need the DM file to see any trends. If your knock count is bouncing around quite a bit at an idle you would want to check to see if the downpipe is hitting up against something, check to see if the fuel lines are banging against the firewall, and see if the motor is rocking around or not (bad motor mounts). The counts will climb when you first start it, then should stop counting up at an idle. Spark retard is the first thing you want to watch while driving.

When the motor cools down take the cap off of the upper IC, start the truck and see if you can see fluid circulating. If not, it could be a bad pump or an air pocket in one of the lines. Use the search button and you'll find lots of threads/remedies.

I'll post up DM file when home and yea I'll search ofcourse it's been my normal nightly thing, I hadn't noticed to much knock bounce while driving but will run tonight, I just mainly wanted to put the screen shots to see responses. Thx for the tips I'll check pump tonight.
 

Flyin Ryan

hated cuz he drives fords
Re: monitoring datamaster pic

IC pump relay might be toast.. Might want to try swapping that with the AC relay on the firewall for the hell of it before dealing with yanking the pump.
 

tydye

Banned
Re: monitoring datamaster pic

IC pump relay might be toast.. Might want to try swapping that with the AC relay on the firewall for the hell of it before dealing with yanking the pump.

yea that's sounds logical, soon as i got home i can hear the air charger cooler bubbling and coming some out the overflow hose. so seems as its not working at all. i know its hot wired before i got it so would that effect how the relay is used at all?
 

tydye

Banned
Re: monitoring datamaster pic

IC pump relay might be toast.. Might want to try swapping that with the AC relay on the firewall for the hell of it before dealing with yanking the pump.

ok instead of the actual relay as mentioned above, i used the all mighty search button and found the "Intercooloer pump fuse ( 10 amp)" that is located behind the alternator and found it was blown, soon as i replaced the fuse i removed the air charger cap and turn ignition to on and immediately saw the pump circulating in the air charger, but also read that the fuse blows before the pump dies, why is this? and what could cause the fuse to blow in the first place? ( and it was blown before the tuneup )
-
new screen shot below, ( bah the screenshot took when i was tapping gas reason why the rpms were up but normal idle was 725)
-
data3.JPG
 
Last edited:

Flyin Ryan

hated cuz he drives fords
Re: monitoring datamaster pic

I believe a dying pump would pull more amps because of the higher resistance... and damn totally forgot about that fuse behind the alt, it's been years since i've had the stock setup.
 

tydye

Banned
Re: monitoring datamaster pic

I believe a dying pump would pull more amps because of the higher resistance... and damn totally forgot about that fuse behind the alt, it's been years since i've had the stock setup.

well when you said relay it made me think i remember someone mentioning a fuse " search button is golden",. lol but i thought about it while looking at the relay lol. well i see about it pulling more amps when older, you think the 500 mile trip back home could have done it? rather then just blow because its going bad? just a thought.
 

WyoSyclone

Active member
Re: monitoring datamaster pic

read that the fuse blows before the pump dies, why is this? and what could cause the fuse to blow in the first place? ( and it was blown before the tuneup )

If the pump shaft gets corroded (bad shaft seal), or if the pump gets clogged up with sediment it will cause a drag on the pump, the pump pulls more current, the fuse heats up then blows. Putting in a bigger fuse just lets the wiring get hotter and creates the possibility of a fire.
I'd pull the lower cooler down (pretty easy), pull the pump off, drain and flush the whole system, etc. You'll sleep better knowing everything is right with it :D
 

tydye

Banned
Re: monitoring datamaster pic

If the pump shaft gets corroded (bad shaft seal), or if the pump gets clogged up with sediment it will cause a drag on the pump, the pump pulls more current, the fuse heats up then blows. Putting in a bigger fuse just lets the wiring get hotter and creates the possibility of a fire.
I'd pull the lower cooler down (pretty easy), pull the pump off, drain and flush the whole system, etc. You'll sleep better knowing everything is right with it :D

yea i think flushing will be a good idea, i didnt put a bigger fuse btw, but it blew apparently from the 500 miles drive home, because it didnt run hot till i was almost home where the altitude went from like 1400 to 5200 miles not that it matters but thats when i noticed it ran hot and heard the air charger bubble.
 

tydye

Banned
Re: monitoring datamaster pic

yea so i replaced the fuse went to work today and the fuse popped again, but before hand i took the ic cap off and saw it had good flow i guess it will always look good even with some small restriction, so i guess i will take the advice and pull it off and flush, i searched but didnt find any write up but its not brain surgery just wanted to see what to expect etc..
 

WyoSyclone

Active member
Re: monitoring datamaster pic

yea so i replaced the fuse went to work today and the fuse popped again, but before hand i took the ic cap off and saw it had good flow i guess it will always look good even with some small restriction, so i guess i will take the advice and pull it off and flush, i searched but didnt find any write up but its not brain surgery just wanted to see what to expect etc..

It's pretty easy to do. One thing that works really good on the inside of the IC and lower cooler is that CLR (calcium/lime/rust) remover that you buy at the store. Just follow the directions for mixing it and let it soak in there for a few hours.. you won't believe the crud that comes out! Use new rubber heater hose lines, a new pump, and you'll be in good shape.
 

tydye

Banned
Re: monitoring datamaster pic

It's pretty easy to do. One thing that works really good on the inside of the IC and lower cooler is that CLR (calcium/lime/rust) remover that you buy at the store. Just follow the directions for mixing it and let it soak in there for a few hours.. you won't believe the crud that comes out! Use new rubber heater hose lines, a new pump, and you'll be in good shape.

ok cool, recommend a pump? see vsrious posts etc
 

WyoSyclone

Active member
Re: monitoring datamaster pic

ok cool, recommend a pump? see vsrious posts etc

Probably just search the threads to see what looks best to you... quite a few threads have pics.... Johnson and ShurFlo are two that come to mind.
 

tydye

Banned
Re: monitoring datamaster pic

Probably just search the threads to see what looks best to you... quite a few threads have pics.... Johnson and ShurFlo are two that come to mind.

thx for the tips. yea i searched so many people try so many pumps lol ill keep reading!
 
Top