Need help...

wantingasy

Active member
Re: Need help...

I typed in Diacom on the c: prompt and nothing happened. I've tried everything possible and nothing will go. Oh well.
 

Don W.

Stab it and steer it
Re: Need help...

OK, at the c:\ prompt type dir (if the list scrolls off the top of the screen type dir/p and you'll see a screen at a time) look for a directory with a name like diacom. If you see one type cd\diacom (or whatever) you'll now see c:\diacom now type dir *.exe and look for an exe file that has a name like diacom. It could be anything from diacom.exe to just d.exe Once you find it try typing just that name only and see what happens.
 

wantingasy

Active member
Re: Need help...

It says.... "Invalid directory" ..... I hate dos
Alright, in "dir"..directory it list 17 files and one of them in there shows DIACOM-P <DIR> 05-04-99 (wow, long time ago) 5:42a
I wonder if I have to have it hooked up in my car while typing in cd\diacom. Then I have to buy an inverter though so I can plug in the laptop because the battery isn't holding a charge. Thanks for the help. I hope to get this figured out soon, or else just buy a newer cable and use the dell (with WINDOWS!!!)
 

dgoodhue

BuSTeD 4.3
Re: Need help...

type in "dir" If their is a lot of directories try "dir /w" look to see if you see a diacom directory. I think I have to type in diacom-p for mine to work but I don't remember, I have it setup to boot up and directly go into Diacom.
 

wantingasy

Active member
Re: Need help...

I got it to where it says c:\diacom-p> What now?
I just had to add the -p and it worked
-edit- cool, I got it going...Just typed in diacom-p in cd\diacom-p prompt and it worked, now it's running. Now comes the next phase in my journey. Running it in the car.
 

wantingasy

Active member
Re: Need help...

Alright, here we go, I went and bought a power inverter today so I can run the laptop in my car. So I got everything hooked up and started up diacom. Immediately my rpms just went up to about 1300 and I don't know what to expect cause it's my first time using it so I figured that's normal. It started sounding like my car was pinging though. So I'm looking at all the stuff it's showing trying to figure out what's what and I don't think my knock is working. Is it labeled "knock retard"? Theres also this section I think is called advance timing....and it shows like 47.1!!!! I'm thinking that's not normal. So I take the ty out for a short drive and it drives wayyyyy differently when diacom is running. Like in drive the rpms are at like 1300 at a stop. I went around the block and came back and it shows trouble codes and there's like 5!!! I didn't write them down at the time but it was like: MAP sensor low, then there was a 35,34 and some other ones. I shut it off, go inside and get a paper and pen, come back and take it for another short drive to collect the numbers again and when I get back it only shows one code and that's 35 ( Idle air control error ) So I do it again a little bit later and the same error is there...So I think that's where I stand right now....Any suggestions/help/info on what I should do? Like I said this was my first time and I need to know how to work this thing..Thanks
 

wantingasy

Active member
Re: Need help...

I need to bring this post back because I haven't used Diacom since that one time and I really need to monitor my car. It's been running funny, but I think it's because it needs a tune up (which is in the mail) My car was running really weird while I was using Diacom and even after it was disconnected so I haven't used it since then :( I'm seriously just thinking about buying a datamaster cable and using a more updated system. What is supposed to happen/the process when I'm running Diacom?
 
Re: Need help...

wantingasy said:
Alright, here we go, I went and bought a power inverter today so I can run the laptop in my car. So I got everything hooked up and started up diacom. Immediately my rpms just went up to about 1300 and I don't know what to expect cause it's my first time using it so I figured that's normal. It started sounding like my car was pinging though. So I'm looking at all the stuff it's showing trying to figure out what's what and I don't think my knock is working. Is it labeled "knock retard"? Theres also this section I think is called advance timing....and it shows like 47.1!!!! I'm thinking that's not normal. So I take the ty out for a short drive and it drives wayyyyy differently when diacom is running. Like in drive the rpms are at like 1300 at a stop. I went around the block and came back and it shows trouble codes and there's like 5!!! I didn't write them down at the time but it was like: MAP sensor low, then there was a 35,34 and some other ones. I shut it off, go inside and get a paper and pen, come back and take it for another short drive to collect the numbers again and when I get back it only shows one code and that's 35 ( Idle air control error ) So I do it again a little bit later and the same error is there...So I think that's where I stand right now....Any suggestions/help/info on what I should do? Like I said this was my first time and I need to know how to work this thing..Thanks

If it's idling at 1300 rpms, it's in ALDL mode

http://www.syty.net/forums/showthread.php?t=4930&highlight=diacom+idle
 

wantingasy

Active member
Re: Need help...

Wow, that's new info to me!! Thanks!!! So if I change it to normal mode before I plug it into the port everything should run normal when I do hook it up? I'll have to give that a try soon. :tup:
 

wantingasy

Active member
Re: Need help...

Alright, I ran the TY in "normal" mode today and WOW!!! Wish I would have known about that from the beginning...lol... Alright, I've been driving around all day with it on and watching everything and trying to learn what everything is. I mainly watched the knock and timing. Is there a standard or "perfect" numbers when at idle for these trucks? There was no knock and no trouble codes everytime I checked it. The "spark advance" seemed a little fishy to me though. I don't know what it's supposed to be, but at idle it's reading like 24.4? I was thinking about just writing down all the numbers while the truck is idling and putting them on here for someone to look at. Should I do that? I can't save the data or anything, so that's the only thing I can do..
 
Re: Need help...

wantingasy said:
Alright, I ran the TY in "normal" mode today and WOW!!! Wish I would have known about that from the beginning...lol... Alright, I've been driving around all day with it on and watching everything and trying to learn what everything is. I mainly watched the knock and timing. Is there a standard or "perfect" numbers when at idle for these trucks? There was no knock and no trouble codes everytime I checked it. The "spark advance" seemed a little fishy to me though. I don't know what it's supposed to be, but at idle it's reading like 24.4? I was thinking about just writing down all the numbers while the truck is idling and putting them on here for someone to look at. Should I do that? I can't save the data or anything, so that's the only thing I can do..

:tup:
 

dgoodhue

BuSTeD 4.3
Re: Need help...

Yeah you want normal mode, I didn't notice this post until just now...

24 degrees at idle is about right, the timing moves around from abour 35-14 on stock timing table, usually isn't need to look at. Somewhere there was a beginner post about what to look at for Datamaster, which is applicable to Diacom as well.
 

wantingasy

Active member
Re: Need help...

Thanks, I'll search for that post. That's good to know about the timing. I thought it seemed kind of high, but I guess not. I'm really happy that there's no knock or trouble codes :tup: I just need to get rid of or at least quite down the ticking under the hood. Pretty sure it's the injectors, but then again I've never been around another TY or SY :oops:
 
Top