need some help learning

sy#2921

BAMF
I recieved this in the console of the SY when it showed up. BG told me it was a prototype switchable chip system he was trying out. My guess so far is the two digit ticker is for boost and timing respectivly. I want to find out what is actually programmed on the chip. I read the chip using my EMP-20 and have the bin file for anyone who can help
363101a5.jpg

if you cant read it, the chip says 50 v4 street all 3 BAG

right now this is what is running in the truck
94969904.jpg

it has a label saying Kris 50#
Kris olsen was the next owner after BG and he was doing most of the tuning to my knowledge of this truck. I was told the truck has gone as quick as 12.1, iev had it to the track once now and on a 3# launch, didnt mess with the tcc switch at all, 50/50 meth water and full atr exhaust (cutout left on) ran 19# all the way down the track shifting at 41-4200 i managed a 12.7
im just trying to learn how to tune this truck to get the max out of the setup untill i start in on the motor
 
Last edited:

SYO237

SyTy Registry
Re: need some help learning

That would be a Dig Chip, and that truck hauled some ass.


He roams the site under the name "turbodig"
 

turbodig

Active member
Re: need some help learning

sy#2921 said:
I recieved this in the console of the SY when it showed up. BG told me it was a prototype switchable chip system he was trying out. My guess so far is the two digit ticker is for boost and timing respectivly. I want to find out what is actually programmed on the chip. I read the chip using my EMP-20 and have the bin file for anyone who can help
363101a5.jpg

if you cant read it, the chip says 50 v4 street all 3 BAG

right now this is what is running in the truck
94969904.jpg

it has a label saying Kris 50#
Kris olsen was the next owner after BG and he was doing most of the tuning to my knowledge of this truck. I was told the truck has gone as quick as 12.1, iev had it to the track once now and on a 3# launch, didnt mess with the tcc switch at all, 50/50 meth water and full atr exhaust (cutout left on) ran 19# all the way down the track shifting at 41-4200 i managed a 12.7
im just trying to learn how to tune this truck to get the max out of the setup untill i start in on the motor


The first pic is an old-school 10-n-1 chip... kind of a predecessor to the Ultimate.

The second one is mine. I fiddled with the truck about a day or so- as I recall, that chip
is a delta off the one BG had in the truck when it was sold (an open-loop smooth idle
job), with some patches and tweaks. Never really got another chance to mess with it
after that.

It should be a low 12s, high 11s setup when dialed in. I'd recommend locking the TCC,
Launching in 2nd (yep, second), then shifting the 2-3 and 3-4 at about 4900 RPM. Get the
boost to 20-22 and you should be there.

Got Data from the 1/4 mile runs?

Later,
 

sy#2921

BAMF
Re: need some help learning

I dont have any data cause i figured those were more shake down runs and i just wanted to see what i could do my first time out. I would try the 2nd gear launch but the way the trans cable is setup (or broken cant figure out yet) i only get OD and D. I wasnt sure how i wanted to mess with the tcc so i just left it. Next time i will lock it when i get in second and see what happens. What would you need to mess with the programming some more?
 
Top