Of Flash chips, and Ultimate boxes...

turbodig

Active member
Not sure if this has been covered here (couldn't find it in a search),
but I ran across something that might be helpful to folks trying to re-burn an Ultimate chip...

JDR (www.JDR.COM) sells an Atmel 29C040 that is pin-compatible with the 27C2001 I've seen in the Ultimates. Not sure if BG has taken to
using different EPROMs lately or not, but every one I've ever seen uses
a '2001.

Anyway, the Atmel chip looks like it will work, it's just twice as big as
the '2001. If you're running a Pocket Programmer, set the start of device offset to 40000, and burn as you would a normal Ultimate.

Lots easier than the burn/erase/burn business....

On a side-related note, anybody tried transtronic's pocket emulator? Looks like they've come a long way with it, and the "hidden" wirte feature looks like it might be nice for on-the-fly programming.

Later,
Dig
 

smeagol

Active member
I'm pretty sure I tried the 020 version of the flash chip and it didn't work. I just grabbed the part number that matched up with the flash version of the 256 that has been used, so the 020 pinouts might not match. Just did some rooting around through my mess and couldn't find it though.

Dig, did you look to see that the 020 version wouldn't work ?
 

PPI Typhoon

DIY Madman
The AMD 040's work well in my setup. The Atmels don't for some reason. This, at least in the Moates adapters. But I've used several AMD chips now, and not had any problems. There's a jumper setup so I can switch from the top 16 programs to the bottom 16 programs, giving a total 32 programs available for tuning / testing runs with DM.

The Atmels 29C256's work well for single chip setups, but the Atmels won't seem to work with the multichip setup. AMD's work like a champ. :D

I'm working on a remote mounted EPROM, and I'm not sure if either will work still or not, but we'll have to see.
 

leroy

Donating Member
Transtronics are only about half a mile away from my house, but I've never visited. I've been meaning to, but seems kind of pointless until I get my truck running.

I'll get around to talking to them, though. Maybe they would come to Nats and give a demo?

Jim
 

turbodig

Active member
smeagol said:
I'm pretty sure I tried the 020 version of the flash chip and it didn't work. I just grabbed the part number that matched up with the flash version of the 256 that has been used, so the 020 pinouts might not match. Just did some rooting around through my mess and couldn't find it though.

Dig, did you look to see that the 020 version wouldn't work ?

The 29C020 looks ok, pinout-wise, but I never found many places that
had that available.

Do you know what -number of an 020 you had? I've noticed before, that
the ECM wants 120 or 150 ns parts.... not faster. Atmel made parts in
the slower speeds, but most places didn't offer 'em. The 256 parts JDR and
others sell are typically -120, that's maybe why they work.

Mouser appears to have the -120s...

http://www.mouser.com/index.cfm?handler=fra_pdfset&dir=612&pdffile=41

Pinout on the 29c020
http://www.atmel.com/atmel/acrobat/doc0291.pdf

Pinouts on EPROMs
http://www.spies.com/~arcade/schematics/ROMref.txt


FWIW, thought I'd check in.

Later,
Dig
 

turbodig

Active member
leroy said:
Transtronics are only about half a mile away from my house, but I've never visited. I've been meaning to, but seems kind of pointless until I get my truck running.

I'll get around to talking to them, though. Maybe they would come to Nats and give a demo?

Jim

That'd be cool. Supposedly, Tunercat will support their emulator in '03,
so maybe we could see the combo in action?

If the hidden write really works on our ECM, it'd be a big advantage over
the LDTI one I'm using.

Later,


Dig
 

kwick6

Donating Member
Re: Of Flash chips, and Ultimate boxes...

turbodig said:
On a side-related note, anybody tried transtronic's pocket emulator? Looks like they've come a long way with it, and the "hidden" wirte feature looks like it might be nice for on-the-fly programming.

Later,
Dig


Quote from an email I got from Xtronics....
The romulator is stand alone and can change data WHILE the car is RUNNING so you can tune the parameters. Also, there is third party software support for the Romutator.

Is there a way that Promgrammer can be utilized with this? I see Tunercat will be available in 03.



Looks like a slick setup. I don't know how user friendly it will be to someone just getting into doing the chip stuff, but we'll see. :D

I'm not one to be taking big chances though and jumping right into WOT tuning... :eek:



Scott
 

Sy769

Donating Member
turbodig said:
smeagol said:
I'm pretty sure I tried the 020 version of the flash chip and it didn't work. I just grabbed the part number that matched up with the flash version of the 256 that has been used, so the 020 pinouts might not match. Just did some rooting around through my mess and couldn't find it though.

Dig, did you look to see that the 020 version wouldn't work ?

The 29C020 looks ok, pinout-wise, but I never found many places that
had that available.

Do you know what -number of an 020 you had? I've noticed before, that
the ECM wants 120 or 150 ns parts.... not faster. Atmel made parts in
the slower speeds, but most places didn't offer 'em. The 256 parts JDR and
others sell are typically -120, that's maybe why they work.

Mouser appears to have the -120s...

http://www.mouser.com/index.cfm?handler=fra_pdfset&dir=612&pdffile=41

Pinout on the 29c020
http://www.atmel.com/atmel/acrobat/doc0291.pdf

Pinouts on EPROMs
http://www.spies.com/~arcade/schematics/ROMref.txt


FWIW, thought I'd check in.

Later,
Dig

So has anyone tested the 29c020 yet? I am really spoiled with the flash chips and don't want to buy a $50 eraser to use on the Ultimate chips.
 
Top