Poly motor mounts 4.3L

turbodig

Active member
Re: Poly motor mounts 4.3L

OK - I was nervous too about vibration etc etc.

It's not that big of a deal - I can't really notice - you certainly don't get a bone ratling sensation. To be honest, I wouldn't be surprised if people got it wrong sitting in my truck and I asked them if it were solids/rubber.

You won't notice... but your electrical connections will, over time.

If you've ever seen electrical devices run on an industrial vibration test, you'll know what I mean.


Im just running stock rubber mounts with my tiedown, and of course using the stock heat shields. Have fun swapping the solids, they can be a pain to get the frame pads on.

x2. I'm not sure why people make this harder than it has to be. If I had it to do again, I'd do stock rubber mounts with Renz's heat shields.

You're not gonna break a stock mount with a tie down on it.

Also, the solids tend to lift the motor up slightly from the stock position, aggravating clearance issues.
 

Quickstop [UK]

Combating adversyty.
Re: Poly motor mounts 4.3L

You won't notice... but your electrical connections will, over time.

If you've ever seen electrical devices run on an industrial vibration test, you'll know what I mean.

.


I hardly think an hour or two of running my truck per year :rotf: is going to equate to a laboratory vibration test but I take your point.

:)
 

Ty1642

Member
Re: Poly motor mounts 4.3L

Another option might be these:

http://www.jagsthatrun.com/Pages/Parts_S10-43-2wdRepacementMounts.html

They make an adapter that works with the 2.8L V6 motor mount. That motor mount is still rubber, but it is surrounded by a metal bracket, so it shouldn't pull apart like the 4.3L mounts. The website has a description of them. Someone posted on here a few years ago about these, but I wasn't able to find anyone that had ever tried them.
 
Re: Poly motor mounts 4.3L

So I ordered up those solid motor mounts above and they are 350 mounts. Like NallJ92 said they are not wide enough for the stock frame pad mount.
So I have these 350 motor mounts that will bolt up to the 4.3L block but not the frame pads. I wanted to see if I could still make this work. RPM has a conversion kit but I wanted to see what else was out there. I found this. Its looks like the best of both worlds.
http://carshop.carshopinc.com/product_info.php/products_id/104232/CSP2375
I know there have been some issues with the poly engine mounts melting. But what about poly frame pads with small block solid mounts. This looks like it could work for less than $80. You would have the strength of solid motor mounts and maybe some vibration dampening with the poly frame pad.
Input please :)
 

Quickstop [UK]

Combating adversyty.
Re: Poly motor mounts 4.3L

Still poly - still an engine mount - still potential to melt if you don't wrap it correctly.

Good find though.
 

nallj92

Active member
Re: Poly motor mounts 4.3L

I dont see them melting as much, but i would still want to use a heat shield around them. You still have the pain of swapping the frame pads, which can be very discouraging. I guess if your set on poly's i would try this before using 4.3 poly mounts.
 
Re: Poly motor mounts 4.3L

So we are still thinking they will melt that far from the block.... Maybe I should just get the rpm pads. I have the motor out so will that still make swapping the pads discouraging?
 

Quickstop [UK]

Combating adversyty.
Re: Poly motor mounts 4.3L

With the motor out it's a lot less of a job.

The trouble with the solids is that there is no give so you have to make sure the alignment its there before tightening everything down. And that means putting the engine in the truck. I never replaced the polys after all the melting/breaking/fan shroud stories so I don't know if maybe it's a bit easier.

It isn't hard, it's just very fiddly and frustrating to get the spanners onto the frame pad bolts - you can't see them and they're hard to feel with the diff and everything in the way.

It's a rite of passage :D
 
Top