Remanuf. ECM?

CavScout

Member
I'm still fooling with a code 45. Tested the entire ignition system and replaced some items. The only thing I can't trust is the ECM, as it's got a big ol' sticker stating that it's remanufactured. Removed the Ultimate chip and the 3-bar sensor and I'm back at stock. Still burning rich.

How could I verify/ test or otherwise make sure that it's the correct one or at least that it's working properly.
Here are some ID#'s if it helps.
On the outside: Number 7-7749
Calibration Code 0798IG
On the Motherboard: 07774900981880163 REMFG
On the PROM(little # on right hand side): 1145180
This is the ECM I bought the truck with and she was running rich when I got her.
Many thanks.
 

93ty475

Donating Member
Re: Remanuf. ECM?

CavScout said:
I'm still fooling with a code 45. Tested the entire ignition system and replaced some items. The only thing I can't trust is the ECM, as it's got a big ol' sticker stating that it's remanufactured. Removed the Ultimate chip and the 3-bar sensor and I'm back at stock. Still burning rich.

How could I verify/ test or otherwise make sure that it's the correct one or at least that it's working properly.
Here are some ID#'s if it helps.
On the outside: Number 7-7749
Calibration Code 0798IG
On the Motherboard: 07774900981880163 REMFG
On the PROM(little # on right hand side): 1145180
This is the ECM I bought the truck with and she was running rich when I got her.
Many thanks.

i have 3 or 4 ecm's running around my place and whenever i'm stumped, i switch one or two out and different chips that my trucks came with and it doesn't usually cure my problem...not to say they don't fail, but i haven't experienced ecm failure yet...two of my ecms are black and say reman as well...if you use a scantool, you might be able to better pinpoint the root of the problem...running rich could be a number of things...i'd play around with the fuel pressure first (with a scan tool) and take it from there...
 

CavScout

Member
Got a scan tool, Actron's superscanner thingy. I did replace the O2 sensor because she did have a crack in the original block and there was no telling how long it had been burning antifreeze.

I have been playing with the fuel pressure. I even pulled the adjusting bolt out, and she still runs rich.

As far as the scantool...I am not that proficient at using it. I am learning, but I simply don't know enough.
 

Jimmy

Banned
My code 45 was a busted diaphram in the fuel pressure regulator.Pull your dipstick and see if it smells like gas.

If you want another 7749 ECM,I can get them all day long for $50 shipped.
 

CavScout

Member
Well, I did a test for that. Used a Mi-T-Vac, applied some vac. and no fuel came out of the vacuum fitting.

But, if there's anything else I need to check...keep it coming.
 

93ty475

Donating Member
Jimmy said:
My code 45 was a busted diaphram in the fuel pressure regulator.Pull your dipstick and see if it smells like gas.

If you want another 7749 ECM,I can get them all day long for $50 shipped.

cavscout,

if you plan on driving the truck much, id take jimmy up on one or two ecm's...i don't know what i'd do without spares...if i didn't have a spare, i'd swear it was the ecm when i've had issues...they do fail though, thats why there are so many remans out there...you could always use an extra to rule that out...i don't know much about tuning either but i try to keep an eye on the INT or integrator....i'm pretty sure that "less than 128 is rich" and "more than 128 is lean"...and if i'm wrong, i'm positive someone will step in here and let me know soon...blm is similar but longer term reading or adjustment...needs to be at a more constant 128...also 02 millivolts should be in the upper 800's or lower 900's and moving quite rapidly...check and reset your tps settings...also verify that the tps voltage sweeps from the correct lowest voltage to the highest voltage without any hiccups in between...you may need another body to help floor it and read the volts while you set it...put your stock fuel pressure regulator back on to see if the scantool values change any...HTH
 

CavScout

Member
Outstanding, this is useful onfo. I am learnng to use the scantool, but I've no idea what is normal readings for most of the items listed on it.
Thank you for this info, right or wrong. It's a starting point.
 

turbodig

Active member
Re: Remanuf. ECM?

CavScout said:
I'm still fooling with a code 45. Tested the entire ignition system and replaced some items. The only thing I can't trust is the ECM, as it's got a big ol' sticker stating that it's remanufactured. Removed the Ultimate chip and the 3-bar sensor and I'm back at stock. Still burning rich.

How could I verify/ test or otherwise make sure that it's the correct one or at least that it's working properly.
Here are some ID#'s if it helps.
On the outside: Number 7-7749
Calibration Code 0798IG
On the Motherboard: 07774900981880163 REMFG
On the PROM(little # on right hand side): 1145180
This is the ECM I bought the truck with and she was running rich when I got her.
Many thanks.


Since it was running really rich before you got it, are you entirely
sure of what injectors someone put in it? A stock chip or aftermarket
chip for stock injectors will throw a 45 with the wrong injectors in it.
I've also seen 40# chips throw a 45 even with the right injectors in it.

I've seen a code 45 when the ground on the bad of the driver's side
head was bad as well.


Just throwing out a few ideas...

Later,

Dig
 

CavScout

Member
I've heard of some problems due to the grounds being loose. Recheked them and both are tight.

Got theold stock 'red-heads' and they have been cleaned, but I didn't get any flow matching done. I am very confident that they are not leaking, as fuel pressure after shutdown doesn't drop for quite some time and is very slow to drop.

Good points, thanks.
 
Top