Remote Zif socket

Sy769

Donating Member
I am going to use my Hyperjunk chip adapter with the 29c256 chips.

It will be a pain to have the computer in the floor all the time. I remember seeing Dig's remounted computer but I can't remember how he did it.


Is there any reason a ribbon cable running between the adapter and a Zif socket mounted in the glovebox or under the computer wouldn't work. That way It would be easy to swap chips with out having the computer out.
 

Sy769

Donating Member
Those are cool. Would be very cool to have it working with promgrammer.
Also very dangerous. :wink:
 

kwick6

Donating Member
I remember smeagol relocated his ecm in the typhoon , but I don't think the pics are up anymore.
 

leroy

Donating Member
A ribbon cable may be subject to some RFI noise....depending on length and location.

Jim
 

turbodig

Active member
leroy said:
A ribbon cable may be subject to some RFI noise....depending on length and location.

Jim

You'd think that, but my emulator cable seems to work fine with about
a 6" length.

Wrap the sucker in tin foil, I think it'd go.

If you really wanted to bulletproof, put some buffers on both ends.
You could probably extend it a foot-18" with that setup.

Later,
Dig
 

Sy769

Donating Member
Thanks Dig I think it would be very easy way to change chips. What do you mean by buffer? Any particular type or spec of cable you'd suggest?
 

smeagol

Active member
I have my ECM in my glovebox now. easy to do if anyone is interested.

Unbolt the white plastic box & the metal bracket from the ECM.

jam/mount the box under the dash somehow, stash the bracket in your garage/crawlspace/garbage.

unplug all 3 plugs from the ECM.

empty glovebox

remove plastic panel from the rear

route the harness & 3 plugs through behind the dash so that you have as much length as possible into the dash (still isn't much)

put the ECM into the glovebox, and plug the ECM in place


This is at least an alternative to the remote setups, or emulators. My Sy is delegated to weekend warrior duty, so I don't have much crap in it, and it fits in my center console. Might not work for the rest of you. Makes chip swaps easy, and eliminates more crap from the floor area for me.
 

Will_in_China

Truckless Wonder
That's fuckin cool Greenie.

How in the fuck did you manage to make those cables reach.
Mine don't even let my ecm hit the floor.

Will have to pull off the DRAC and see how far I can stretch it...

Sick of it getting hung up on the stupid light and burning my goddamn hand.

How much room is left on top of the damn thing?
Heat from ECM?

Badass!

Although I was going to put a pc in there to run diacom and mp3's and dvd's and shit....

-Will
 

Sy769

Donating Member
I might try that route. Don't use the glove box much and hey the best part is that it doesn't cost anything.
 

smeagol

Active member
DCP_1554.JPG
 
B

Blake

Guest
Just did this today. Fits in there like it was supposed to go there.
That doublesided tape GM put on that bracket to hold it on the ecm was really tough to get a thin flat blade paint scraper under. But it'll come off dammit.
Over on the right in Brian's picture where the connector's wires kinda round that corner, I had to take a hacksaw and cut over about 1 1/4". One cut along the bottom of the opening and the other about an inch up. Took a pair of plyers and just snapped it off.
It allowed the ecm to sit in there straight and gave the wires room so they weren't stressed. My harness didn't have near as much extra as Brian's did.
There is a little pocket on top of the shelf area that runs along the underside of the dash. This little white box(for the VSS or DRAC or something) that was removed from the ecm will fit in there perfectly.
Whole project took about 20 or 25 minutes.
Something else that helped. It is kinda narrow back in there when you route the connectors over the heating/ac duct. If your harness is taped all the way up to the connectors(like mine was), just remove the tape about 6 or 8 inches down. It frees up the wires a little so they can lay flat on the edge of the duct and lets you get the connectors far enough apart so you can fish them through one at a time.
Those little studs on each end of the ecm just have spring loaded anchors. You can take a flat head screw driver and just push them off. Gave another 1/2" of room on the left hand side for the connector wires to reach better.
Thanks for putting this idea out there, Brian.
Blake
 
Top