Running lean FOUND for REAL

Don W.

Stab it and steer it
Coming home from the track last night (3rd place :tup:) truck started running real lean, almost to the point of dieing, at part throttle. Just before manifold pressure crosses over from vac to boost it will smooth out and run just fine. All my FT runs last night were right at 12 flat.

I don't think it's a vac leak because it will idle, barely, at the correct RPM but of course I will check. Just driving it's as if the it's either the MAP sensor or TPS. Fuels pressure is correct.

I will do a DM run and and see what comes up but meantime if you want to throw some ideas out I'd appreciate it.

Thanks.
 
Last edited:

WyoSyclone

Active member
Re: Running lean

Re: Running lean

Hmmm, sure kind of sounds like an intake manifold gasket leak... maybe try the old pressurizing the intake routine and see if you can spot anything.
 

Don W.

Stab it and steer it
Re: Running lean

Re: Running lean

Hmmm, sure kind of sounds like an intake manifold gasket leak... maybe try the old pressurizing the intake routine and see if you can spot anything.

Thought that it might be the plenum gasket also. Fresh build on the motor and I was very careful with those gaskets so I doubt it but ya never know. If it was a leak of some kind why is idle RPM correct? My experience is that idle RPM goes up but the size of the leak prolly affects it also.

Keep the ideas coming should have a DM run later today or tomorrow.
 

WyoSyclone

Active member
Re: Running lean

Re: Running lean

Thought that it might be the plenum gasket also. Fresh build on the motor and I was very careful with those gaskets so I doubt it but ya never know. If it was a leak of some kind why is idle RPM correct? My experience is that idle RPM goes up but the size of the leak prolly affects it also.

Keep the ideas coming should have a DM run later today or tomorrow.


I would think that the ECM would tell the IAC to close down to compensate for the leak.. at least as far as it was able to... look at the IAC info from a previous DM run and compare it to the new run you do today or tomorrow.. maybe that will tell you something :D
 

Don W.

Stab it and steer it
Re: Running lean

Re: Running lean

Look at this DM file. It's just a run down the street. But the problem is there. Hint: I think it's electrical.

http://www.sonic.net/~donpris/AutoLog_172.uni

I think I'm loosing the alt above part throttle because of either bad alt :tdown: or belt slippage :tup:from my AC delete kit not pulling the belt tight enough.
 

TYTILIDIE

METH HEAD
Re: Running lean FOUND, I think

Re: Running lean FOUND, I think

I am seeing your AFR's in the 12's and 13's, is this correct? Or are you talking about when you are 0 tps? I do see some pretty good voltage drops, does your belt make noise?
 

Don W.

Stab it and steer it
Re: Running lean FOUND, I think

Re: Running lean FOUND, I think

Not sure on the AFR's but they're prolly haywire anyway because of the voltages. Belt does not make noise. If I watch the dash volt-meter as soon as I pass about 1000 rpm voltage drops almost as if the alt goes off line. It stays there until RPM comes back down so it's either the belt or the alt itself.
 

Osmosis

New member
Re: Running lean FOUND, I think

Re: Running lean FOUND, I think

What is your altenator doing? The first time I took my Z to the track with the supercharger on it, I was running hi 13's and I was thinking...wtf????? The car did not have any stumbles, but as the night went on and it got dark, I noticed my lights were dim, then....I noticed my volts were low. Replaced my altenator, problem solved. Just a thought here, I"m sure it's not the problem, just a though;)
 

sytyguy

Moderated User
Re: Running lean FOUND, I think

Re: Running lean FOUND, I think

Swap Alternator with known good.....this is exactly what plagued Robert's Syclone to start with.
 

Don W.

Stab it and steer it
Re: Running lean FOUND, I think

Re: Running lean FOUND, I think

Thanks guys. Revamped exhaust going in Monday then I'll tackle this. Will post the results.
 

Don W.

Stab it and steer it
Re: Running lean FOUND for real

Re: Running lean FOUND for real

OK, problem found for real this time. Was looking around the trying to decipher what was going on and low and behold found the field connector to the alternator loose. Either it came loose on its own (unlikely) or I didn't fully seat it it when I installed the alt when the motor was installed last winter. (Likely) Why in the heck that thing would work below 100RPM and quit above is is interesting but I didn't waste any time on it.

Plug the thing is like it belongs and all is well. Funny how that works... :rotf:

Thanks for all the ideas everyone.
 
Last edited:

WyoSyclone

Active member
Re: Running lean FOUND for REAL

Congrats and thanks for posting the solution Don :tup: We all learn the more we see these problems solved... I know I'll digest it and put it in the old brain somewhere!

EDIT.. Your diagnosis from the DM run was right on the money... I never did look at that file.. I'll have to save it and label it as a 'bad alt connection' file.
 
Top