some questions about running code 59

BMFB

Not to scale
ok, so im getting ready to start running code 59, theirs just a few things im not sure about, and thats
the fuel pressure regulator
the wideband o2 sensor
the stock ecm as it is now.

ok, so the wide band, I was thinking that it was going to replace the narrow band, but the more i think about it and look into it, that doesn't seem the case, it looks like its supposed to be there just to compliment the narrow band, and that i have to cut a new bung into my down pipe, am i correct?

next, i got a new walbro pump, and i was thinking that I needed to run a new adjustable fuel pressure regulator, but i haven't really seen that written anywhere. i was under the idea that i should be turning up my fuel pressure to my injectors, so I thought I should ask.

next, the ecm, I know that i have to rig in the wideband, and that the stock chip gets replaced by a G1 adapter, but is that it? do i have to make any other changes? I cant seem to find anything that leads one way or the other, so I thought I would ask

what im looking for with this is to keep full street-ability and be able to run maybe in the 13 flat area, I have a 3 bar map sensor so I can take the boost pressure up a bit as i need to but the motor and everything else is stock. but yea, any help is always greatly appreciated, ive been digging around but I always find stuff that kinda counters what other stuff says...
 

dgoodhue

BuSTeD 4.3
Re: some questions about running code 59

With the stock injectors you want to raise the FP somewhere around 50# because it will allow them to flow more fuel and the stock injectors with the stock FP has very little head room.

You can cut a new hole in your downpipe. If you really want to, Most WideBand O2's narrow band input, so you don't have to cut another hole.

Yes the G1 is all you need plus the Latop/TunerPro/Emulator (ie Ostrich) and ALDL cable.

BTW I think it's great to be doing code $59 on otherwise stock truck :tup:
 

WyoSyclone

Active member
Re: some questions about running code 59

ok, so im getting ready to start running code 59, theirs just a few things im not sure about, and thats
the fuel pressure regulator
the wideband o2 sensor
the stock ecm as it is now.

ok, so the wide band, I was thinking that it was going to replace the narrow band, but the more i think about it and look into it, that doesn't seem the case, it looks like its supposed to be there just to compliment the narrow band, and that i have to cut a new bung into my down pipe, am i correct?
No, you don't have to install a new bung... with my PLX I replaced the factory o2 sensor with the new Bosch. PLX says that the stock location is OK unless you're running a high HP motor

next, i got a new walbro pump, and i was thinking that I needed to run a new adjustable fuel pressure regulator, but i haven't really seen that written anywhere. i was under the idea that i should be turning up my fuel pressure to my injectors, so I thought I should ask.
The Walbro pump is a good idea regardless, but if you're running a stock motor you shouldn't have to run an AFPR unless you start turning boost up over stock. I'd leave it for now and as you start logging you'll see whether your injector DC is being maxed out.

next, the ecm, I know that i have to rig in the wideband, and that the stock chip gets replaced by a G1 adapter, but is that it? do i have to make any other changes? I cant seem to find anything that leads one way or the other, so I thought I would ask
There's a good thread on here about integrating into the ECM. I run mine wideband only. Once you get the G1 and programmer you'll download a starter BIN from the '59 site, burn it on the chip, go out for a drive to log it, then start making your mods.
what im looking for with this is to keep full street-ability and be able to run maybe in the 13 flat area, I have a 3 bar map sensor so I can take the boost pressure up a bit as i need to but the motor and everything else is stock. but yea, any help is always greatly appreciated, ive been digging around but I always find stuff that kinda counters what other stuff says...

see above....
 

BMFB

Not to scale
Re: some questions about running code 59

Alright, the clears up alot, ill go with keeping my stock pressure regulator until i know it wont do what i need it to anymore, and its good to know that most widebands will also do teh work of the narrow band. thanks for the reassurance on putting code 59 on a pretty stock truck, i was worried it was going to be kind of an unnecessary thing to do
 

JSM

Active member
Re: some questions about running code 59

Narrowband is really not needed with code59 at all.
 
Top