Spliting the ECM inj drivers

Don W.

Stab it and steer it
I did this today:

http://www.syty.net/forums/showthread.php?t=57813

Just moved the wire, nothing else. If you look at post 5 it mentions the "sense resister." How big a requirement is that? Am I gonna fry my ECM? I ask because the truck runs fine. I did a couple of test launches and it sure looks like I have much less spark retard than before. (Not that I had a lot before but on these launches the line is dead flat on DM.)

And if I need to change it where is it. And don't just say it's in the ECM... :rotf:

To be safe I'm not driving the truck.

TIA
 

nallj92

Active member
Re: Spliting the ECM inj drivers

if im reading that post correctly, the resistor is only for converting to Peak and Hold. You should be able to just do the jumper and run both drivers without doing the resistor for Peak and Hold


Heres a quick ex of the P & H from RC engineering:



Injectors are classified into two categories.
1. High impedance/resistance (saturated) 12-16 Ohms.
2. Low impedance/resistance (peak & hold) 0.5-6 Ohms.

Saturated injectors require roughly 1-1.5 amps to open the injector. Peak & hold injectors initially needs about 4-6 amps, and once open drops to roughly 2-3 amps to keep it open.

ECU design will dictate the use of one or the other. Most late model cars will use saturated injectors.
 

SY-1193

Active member
Re: Spliting the ECM inj drivers

I did this today:

http://www.syty.net/forums/showthread.php?t=57813

Just moved the wire, nothing else. If you look at post 5 it mentions the "sense resister." How big a requirement is that? Am I gonna fry my ECM? I ask because the truck runs fine. I did a couple of test launches and it sure looks like I have much less spark retard than before. (Not that I had a lot before but on these launches the line is dead flat on DM.)

And if I need to change it where is it. And don't just say it's in the ECM... :rotf:

To be safe I'm not driving the truck.

TIA

Switching the wire...that's it...nothing else. No reisistors need to be changed if you have HIGH IMPEDANCE injectors like the stock ones. The only time you need to change the reisistors are if you use LOW IMPEDANCE injectors. it is discussed on Code$59 Forum in more detail here: http://www.code59.org/index.php?opt...=view&id=2590&catid=15&limit=10&limitstart=20
You can skip to cell #2939 for the Stock Injector part of it. The rest is more in depth about Peak & Hold and 8cyl. stuff. Don't over think it. It is that simple for a stock truck/high impedance injectors.

So whats the reasoning for doing this?

This takes the load of six injectors and splits it in two reducing the load by 1/2. Really you won't recoginze any difference but you have probably increased the longevity.
 
Last edited:

Don W.

Stab it and steer it
Re: Spliting the ECM inj drivers

Thanks Kieth & Nallj92.

I swear it mad a difference on how it runs. But even if it didn't but I think it did that's a good thing right?:rotf:
 

The Bronze

New member
Re: Spliting the ECM inj drivers

I am sitting here sick today, so I made this to show what electrically is happening on the four styles of injectors.

Here is the Saturated Injector:



SaturatedInjector.jpg



Here is the Peak and Hold Injector:


PeakandHoldInjector.jpg



Here is the Bosch Peak and Hold Injector:


BoschPeakandHoldInjector.jpg


Here is what a PNP Injector would look like. This is just a manipulated Saturated Injector waveform so don't start calling out the flaws!:

PNPInjector-1.jpg
 
Last edited:

BoostedSUV

Active member
Re: Spliting the ECM inj drivers

I've been running my ECM wired this way for years now. Never noticed any difference but it took 5 mins to do and I haven't seen any ill effects. Like Keith said it will probably add some longevity since you are using 2 injector drivers instead of one. Takes some of the load off.
 
Top