Started new engine, now it stalls when I turn.

Methuselah

New member
<update> Even more issues, please read below <update>

Last night I fixed the issue with fuel squirting around the tops of the injectors (not an insignificant effort, and the fuel rail itself needed to be bent to an appropriate angle). Anyhow, I was finally ready to start the truck.

When I hooked the battery up I realized there were no interior lights. I checked all the fuses, scratched my head, and eventually got lucky when I found that I had not connected the red/black wire. I attached it to the +12V terminal on the firewall and everything seemed fine. I turned the key and the fuel pump primed the rails, and then nothing happened when I tried to turn the engine over.

And then things started getting wierd. I turned the key back and tried again, at this point, all of the lights went out, and the "Anti-lock" light came on and stayed on. That was it, just that light. I uplugged the battery, plugged it back in, and just the antilock light came on. I unplugged the battery again, waited for a long while, unplugged the red/black connector from the ABS unit just for kicks, and started screwing the ground terminal back into the battery.

As I was doing this, the cabin lights came on. Just after this, I touched the wrench to the body (screwing in ground) and this caused a bit of a spark, and the cabin lights went out. With the battery still connected I found that the engine was at +12V relative to ground.

How could this have happened? I realize that I could have connected some wiring incorrectly, but why did everything seem to work up until I tried to crank the engine, and then all of a sudden the vehicle isnt grounded, but instead at 12V?

Thanks for the help,
Seth.
________
Yamaha blaster
 
Last edited:

leroy

Donating Member
I think the red/black wire you are talking about goes from the battery to the alternator. Is it about a 10 gauge?

Jim
 

JSM

Active member
double checks grounds on engine also.. not that I would have ever had any trouble with that or anything... :-?
 

Methuselah

New member
Jim, the red/black wire I am refering to comes straight off of the battery, so it makes sense that it should hang off the alternator. Unfortunately, Im making the wiring stuff up, since I dont have much for reference.

I believe I have squashed the electrical gremlins. I had an intermittent ground as Jeff suggested AND I forgot to tighten down the positive lead to the starter, which seemed to have shorted against the ignition lead.

However, although the truck will turn over now, it wont start, and stops cranking after a bit. Kind of makes a Pac-Man dying sound. I did this with my Ranger on and the Syclone jumped to it.

I verified ignition by checking for spark in #1. Although it was a little tricky, I verified timing by basically flashing the timing light in my face while the truck was cranked, and watching that the timing mark was pretty damn close. I verified fuel pressure by priming the rail a good long while, and making sure I got a good squirt from the schraeder valve (I dont have a fuel pressure gauge at the moment).

Other than that, Im at a loss. What else could I be missing?

Thanks.
________
Rc161
 
Last edited:

Methuselah

New member
I forgot to mention that I verified the fuel injector on #1 was working by listening for the "tick" with a mechanic's stethoscope.

Although this doesnt necessarily guarantee I have fuel being injected it's as good as I can get without taking the rail out and looking at the injector squirt.

I will verify fuel pressure tonight with an actual fuel pressure gauge.

Shouldnt the engine continue to crank (assuming there's enough juice in the battery)? Mine gets about two slow revolutions before it just dies out.
________
Chrysler c platform history
 
Last edited:

smeagol

Active member
crank it - pull a plug.. got fuel? ok step 2

yank a plug wire, put a spark plug in it, crank, and watch for spark... (don't hold it, rest it on the frame or something)

got fuel, got spark, you should have a running truck

this will give you a start where to look...
 

Methuselah

New member
GM Turbo said:
I think - I could be off......

If there isn't enough oil pressure it won't start....

Is this true? I primed the oil pump a good long time before I tried to start the engine the first time...4 days ago now.

smeagol said:
crank it - pull a plug.. got fuel? ok step 2

yank a plug wire, put a spark plug in it, crank, and watch for spark... (don't hold it, rest it on the frame or something)

got fuel, got spark, you should have a running truck

this will give you a start where to look...

I didnt say it explicitly, but I did pull a plug, taped it onto the alternator so that I could see a spark when I cranked...the spark was there. In your first statement, do you mean to say that the plug will be wet if the intake charge did not combust? That is, what exactly do I look for when I pull the plug after cranking to verify fuel was delivered properly?

Mad Mike said:
Try replacing the fusible link behind the alternator.

I verified the link behind the alternator had continuity.

If Dave is correct about the oil pressure...I may be hosed (building pressure again will be a huge irritation). Bear in mind that I have no "real world" experience with starting a new engine, so some things may need to be explained in a bit more detail.

Thanks for all the input guys, please keep it coming.
________
Ford D186 Platform
 
Last edited:

Methuselah

New member
Im going to use starter fluid to get the engine to turn over. Im starting to think, based on what Brian implied, that the plugs should be wet with fuel and stink of gas. If the engine turns over with starter fluid then at least I can concentrate on why fuel is not being injected properly.
________
CHEAP AIRSOFT SHOTGUN
 
Last edited:

4C FED

Absolutum Dominium
Methuselah said:
GM Turbo said:
I think - I could be off......

If there isn't enough oil pressure it won't start....

Is this true? I primed the oil pump a good long time before I tried to start the engine the first time...4 days ago now.

No, there is no oil pressure switch present in our motors.
 

Methuselah

New member
Here's a new one for you guys: The problem was that the starter (a used aftermarket noname lightweight) was not disengaging from the flexplate, causing the engine to stall. Im still a bit confused, because it didnt sound like the engine was trying to start at all. Seems like some spacers were definitely required on this starter...I replaced it with a stocker.

Anyhow, I got the truck started. It sounds like ass, especially with the open downpipe. I didnt secure the vaccum harness very well, so that may explain the 500rpm fluctuations when I give the truck gas. Im not too worried about it though.

I am worried, however, about the truck stalling out when I try to turn it. Why is the power steering pump putting such a great load on the engine? It has been maybe 3 years (not really sure) since the truck was run last. I bought it sans drivetrain last November-ish.

Thanks.
________
Ffm Bikini
 
Last edited:

leroy

Donating Member
Remove the belt and turn the p/s pulley by hand. If it turns easily, you most likely have a tuning issue. Suspect vacuum leaks.

Jim
 

4C FED

Absolutum Dominium
Methuselah said:
Here's a new one for you guys: The problem was that the starter (a used aftermarket noname lightweight) was not disengaging from the flexplate, causing the engine to stall. Im still a bit confused, because it didnt sound like the engine was trying to start at all. Seems like some spacers were definitely required on this starter...I replaced it with a stocker.

What starter are you using?
I mentioned this before about my CVR.
 

Methuselah

New member
At a loss for why the truck was so quick to stall out, I discovered that the previous owner was nice enough to leave me a custom 3 bar chip, but I hooked up a 2 bar map sensor to it. Since I dont have the 3 bar map sensor at the moment I went back to a stocker from the Typhoon.

I put in a few more quarts of tranny fluid and that gives the tranny enough juice to shift. I took the truck around the block and it wouldnt shift out of first, so I guess I need to adjust the TV cable.

The torque converter from the previous owner doesnt let the truck move until about 1700rpm or so. Yikes.

Seth.
________
Chevrolet Uplander Specifications
 
Last edited:
Top