stg serial # ?

black cat

New member
got an stg that is too lean on stock injectors and too rich on 50#. the serial # on the stg isc3b1697. anyone know what size of inj it might need or do i buy every inj made and try them:rant:
 

NorwegianTy

New member
Re: stg serial # ?

Dont know to much about these chips myself but would suggest trying to rise the fuel pressure a bit (with the stockers or lower it with the 50#) and see where that gets you (or just trade the chip for another that you are certain match your setup)
 

SY-1193

Active member
Re: stg serial # ?

Do you have a 3-bar Map Sensor installed? I think that is a stock injector / stock head version # for a 3-bar Map Sensor... but I could be wrong. If you don't have the 3-bar installed it will throw things off. Also do you have an adjustable fuel regulator in place?...check your fuel pressure I believe the chip is based on a 50 pound base fuel pressure setting.

http://www.sytychips.com/
 
Last edited:

black cat

New member
Re: stg serial # ?

hey . i have a 3 bar in it. originally i had the fuel pressure at 52 lbs on the stock inj but everone said that was wrong and to put it at 43. i never really tried it at 52 because it did set a code for too rich. but it kinda points out that stockers might of worked . i don,t want to set the fuel press on these 50 lbs that i have in now too low because of the poor spray pattern. i,ll reinstall the stockers and set the fuel press back to 50-52 and see what i get. is it possible it was programmed for something in between the stockers and 50 lbs
 

SY-1193

Active member
Re: stg serial # ?

throw the stock inj. back in set the fuel pressure to 50 and see what you have. I ran that set up as low as 46 lbs.but you don't want too lean. So start at 50.
 

black cat

New member
Re: stg serial # ?

hey reinstalled stock inj . set fuel to 52 lbs. took a drive. at idle scanner is trying to pull a little fuel . not major though.cruising scanner shows trying to add fuel not major though.put foot into it wide band did aquick dip to 10.9 them up to12.9.let off. then stompped pedal truck took off for a sec wide band was at 12.0 and then rose alittle bit then it just backfired. let off and went home. with fuel at 52 stock inj work out to about 38 lbs. it is acting like it still needs more inj like 42 lbs?. with the 50 lbs it was always too much fuel but it didn,t run that bad accept when i really got my foot into it it just bogged.i thought there were only a couple of programs for the stg stock inj and 50lbs. thks
 

SY-1193

Active member
Re: stg serial # ?

Check your adjustable fuel pressure regulator. Remove the vacuum connection on top of the regulator check that no fuel is present...(bad diaphragm). Also check your vacuum lines. The regulator should increase 1lb of fuel pressure in relation to manifold pressure. Can you drive it and watch the fuel pressure at the rail to see what it is doing?

Ultimate was made for Stock or 50lb injectors only. Was your chip altered or not an original? l think it is original if the sticker is in place. (it should have a sticker on it- probably where you read the version #).
 

black cat

New member
Re: stg serial # ?

hey . regulator is new . i set the fuel press with engine running vacuum line off and plugged. when i install the vacuum line it drops the fuel pressure by about 5-6 lbs.i have taken it for a drive with aguage before. and depending on base pressure it rises a 1 lb per 1lb of boost.i have new 255lpm walboro in it.i just removed the stg put the 2 bar back in set fuel to 44 and went for a rip . flawless. 11.3 to 11.5 a/r at 14 lbs i,m kinda at a wall with this stg . it works well until you really get into it.then it just seems to be too lean (stock inj) the sticker is still on the stg and in good shape. i,m going to sell the stg thks
 

dgoodhue

BuSTeD 4.3
Re: stg serial # ?

Did you buy you new Walbro from a reputable source? Do you currently have a fuel pressure guage install? I wonder if your losing fuel pressure at higher FP levels. A Walbro should be able to keep up, but their are tons of chinese knocks and even some bad ones from walbro themselves.
 

black cat

New member
Re: stg serial # ?

i don,t have the guage on now.but if the stock setup ( inj, ecm, boost@ 14, fuel pressure @44) can keep up why can,t the stg keep up even at the lowest setting T15. it won, t even get to 15 lbs before the wide band shows too lean and i have to let off. i,ll put the guage back on and see if it drops but i don,t expect to see it drop . thks again ps .this is an hour after i posted the first part of this message. i do have 3in exhaust and a bigger turbo. my tuner guru said that this is probably what is throwing the stg for aloop. sorry for saying that this was a completly stock setup. its almost impossible to diag from what people like me give u for info but i do appreciate the input thks
 
Last edited:

dgoodhue

BuSTeD 4.3
Re: stg serial # ?

i don,t have the guage on now.but if the stock setup ( inj, ecm, boost@ 14, fuel pressure @44) can keep up why can,t the stg keep up even at the lowest setting T15. it won, t even get to 15 lbs before the wide band shows too lean and i have to let off. i,ll put the guage back on and see if it drops but i don,t expect to see it drop . thks again ps .this is an hour after i posted the first part of this message. i do have 3in exhaust and a bigger turbo. my tuner guru said that this is probably what is throwing the stg for aloop. sorry for saying that this was a completly stock setup. its almost impossible to diag from what people like me give u for info but i do appreciate the input thks

15+52= 67psi, 14+44= 58psi, For fuel pumps the higher the pressure, the less volume it has the capacity to pump.
 
Top