stg ultimate info

92boosted303

1992 Typhoon #1155
Re: stg ultimate info

I'm interested in hearing how you get the diferent tunes to work on the ultimate if you can share that.
 

dgoodhue

BuSTeD 4.3
Re: stg ultimate info

The ultimate is just 16 bin stacked in one PROM memory chip. $58 bins are 4000h long, so the programs are located at 0h, 4000h, 8000h, B000h, ect. You need a binary editor to do this.

It is time consuming to pull all 16 programs apart, makes changes and then restack them.
 

gearhead143

New member
Re: stg ultimate info

Todd Austin is the person who did the hardware for the Ultimate, he hasn't had a Typhoon is over 10 years. Brian Green is the person who did the tuning. He hasn't had a SyTy is a good 7-8 years either. Their were other people behind the scenes as well that contributed to the design.

What kind of questions does your tuner have? Does he have tuning questions? Does questions on how to make the different tunes work on the ultimate chip hardware?

Breaking out the the tunes and inserting them back is easy, just takes some time. The question I have is why Brian locked the LT and used ST for all closed loop fueling? I have only had a little time running it in the shop ( No drive time) and ST is 160 at closed throttle (idle) level 3. He also has a lot of timing here ( idle surge).

Any insights on why he did this would be great.
 

TurboTYPHOON

New member
Re: stg ultimate info

Breaking out the the tunes and inserting them back is easy, just takes some time. The question I have is why Brian locked the LT and used ST for all closed loop fueling? I have only had a little time running it in the shop ( No drive time) and ST is 160 at closed throttle (idle) level 3. He also has a lot of timing here ( idle surge).

Any insights on why he did this would be great.

IF you are lucky he will see this and respond. IF you are lucky. He still logs in from time to time even though he doesn't have a syty any more that I am aware of.
 

gearhead143

New member
Re: stg ultimate info

IF you are lucky he will see this and respond. IF you are lucky. He still logs in from time to time even though he doesn't have a syty any more that I am aware of.

Thank you for the reply to my question, but since Dave asked me some specific questions, and by his reply to s_blazin seems to know what Todd and Brian were doing between hardware and tuning that he would be able to shed some light on my question or put me in-touch with Brian.
 

gearhead143

New member
Re: stg ultimate info

Also How do I turn off that stupid Avatar below my name?? I went in and shut off every thing that pertains to Avatars! and its still there.
 

smeagol

Active member
Re: stg ultimate info

I stumbled upon this thread, not sure if I can shed too much light at the moment, but I'll do what I can.


We only sold calibrations for stock injectors and 50 lb/hr injectors.

The stock injectors were closed loop, similar/identical to stock in that respect.

The 50lb/hr calibrations were made open loop. That was a decision on my part, and could be argued whether or not it was good/bad/correct. I had very good luck with open loop, and bad experiences with closed loop on syty's. I'm going on the assumption you have one of my 50 lb/hr calibrations.

- Warning - going off on a bit of a technical rant/tangent here..
Quick background, hope I don't get much wrong here, as it's been years and years since I worked on a syty calibration.
Syty's have 2 block learn values. This is a long term fueling trim really, usually represented as LT or LTFT in other forums/discussions. One value is used at closed throttle (idle), the other is used at open throttle. My big complaint of this configuration was that the program attempted to make long term fueling adjustments for ALL conditions where the throttle would be open using a single value. So if you took a long ride cruising at 1800 RPM, and it was *slightly* rich, your BLM/LTFT would go lean (<128). Next your driving condition changes... and you have a slight stumble at off idle, or it's really lean at 3400 RPM.. because your BLM/LTFT is "fighting" you and is removing fuel for the condition it learned at the 1800RPM cruise. I had similar experiences with the STFT, where it would cause rolling conditions. Now you can play with the parameters in the chip for a long time, try adjusting PID stuff, or what have you. I did some testing and really liked the experience of open loop. I liked having my truck idle *slightly* richer than stoichiometric. I liked having it cruise slightly leaner than stoichiometric. It felt smoother not having computer correction involved. Also, the 50lb/hr calibrations were geared towards people with heavy modifications, where emissions was a secondary concern. They also had the goal of allowing for some adjustability. The instructions were that you could adjust fuel pressure for best idle/drivability, and then scroll through the programs for WOT fueling adjustments. I don't have the exact calibration program mapping, but it was along those lines.
I believe it's accurate here: http://www.sytychips.com/50lbdescription.html

As far as specific calibration questions from gearhead -
The question I have is why Brian locked the LT and used ST for all closed loop fueling? I have only had a little time running it in the shop ( No drive time) and ST is 160 at closed throttle (idle) level 3. He also has a lot of timing here ( idle surge).

The 50lb/hr calibrations were set to open loop fueling in all but the valet program. Are you getting your LT/ST data from a scan tool or from the calibration? I believe I just set it to open loop based on coolant threshold, not by locking STFT/LTFT values (but I could be wrong). Meaning, the closed loop flag would never be set, the values would read 128 (or zero) depending on the scan tool. The valet program would be closed loop, and should have stock-like values for closed loop operation. I don't recall anything changed as far as timing goes in the valet chips.

I would start with a stock-like base fuel pressure on these programs (43.5psi line off). The idea was that a stock-ish truck could get away running without an adjustable FPR, but might not have the full adjustability offered if there was one installed. This is assuming the truck has a stock motor, and running the Delphi/MSD 50lb/hr injectors that the calibration was based on. If I'm wrong on either of those counts, you'll need to get some sort of custom calibration done.
 

gearhead143

New member
Re: stg ultimate info

I stumbled upon this thread, not sure if I can shed too much light at the moment, but I'll do what I can.


We only sold calibrations for stock injectors and 50 lb/hr injectors.

The stock injectors were closed loop, similar/identical to stock in that respect.

The 50lb/hr calibrations were made open loop. That was a decision on my part, and could be argued whether or not it was good/bad/correct. I had very good luck with open loop, and bad experiences with closed loop on syty's. I'm going on the assumption you have one of my 50 lb/hr calibrations.

- Warning - going off on a bit of a technical rant/tangent here..
Quick background, hope I don't get much wrong here, as it's been years and years since I worked on a syty calibration.
Syty's have 2 block learn values. This is a long term fueling trim really, usually represented as LT or LTFT in other forums/discussions. One value is used at closed throttle (idle), the other is used at open throttle. My big complaint of this configuration was that the program attempted to make long term fueling adjustments for ALL conditions where the throttle would be open using a single value. So if you took a long ride cruising at 1800 RPM, and it was *slightly* rich, your BLM/LTFT would go lean (<128). Next your driving condition changes... and you have a slight stumble at off idle, or it's really lean at 3400 RPM.. because your BLM/LTFT is "fighting" you and is removing fuel for the condition it learned at the 1800RPM cruise. I had similar experiences with the STFT, where it would cause rolling conditions. Now you can play with the parameters in the chip for a long time, try adjusting PID stuff, or what have you. I did some testing and really liked the experience of open loop. I liked having my truck idle *slightly* richer than stoichiometric. I liked having it cruise slightly leaner than stoichiometric. It felt smoother not having computer correction involved. Also, the 50lb/hr calibrations were geared towards people with heavy modifications, where emissions was a secondary concern. They also had the goal of allowing for some adjustability. The instructions were that you could adjust fuel pressure for best idle/drivability, and then scroll through the programs for WOT fueling adjustments. I don't have the exact calibration program mapping, but it was along those lines.
I believe it's accurate here: http://www.sytychips.com/50lbdescription.html

As far as specific calibration questions from gearhead -


The 50lb/hr calibrations were set to open loop fueling in all but the valet program. Are you getting your LT/ST data from a scan tool or from the calibration? I believe I just set it to open loop based on coolant threshold, not by locking STFT/LTFT values (but I could be wrong). Meaning, the closed loop flag would never be set, the values would read 128 (or zero) depending on the scan tool. The valet program would be closed loop, and should have stock-like values for closed loop operation. I don't recall anything changed as far as timing goes in the valet chips.

I would start with a stock-like base fuel pressure on these programs (43.5psi line off). The idea was that a stock-ish truck could get away running without an adjustable FPR, but might not have the full adjustability offered if there was one installed. This is assuming the truck has a stock motor, and running the Delphi/MSD 50lb/hr injectors that the calibration was based on. If I'm wrong on either of those counts, you'll need to get some sort of custom calibration done.

Thank you for the reply, and your thoughts on why you built the tunes the way you did. Now to answer some of the questions to me.


- Yes this is a 50lb/hr calibration (injector flow rate 7.97gal/hr) and I was told it was for the L35 head combo, which is what this engine is.

- Yes I used a scanner to look at LTFT and STFT, LTFT was at 130 and STFT was at 160 when it was in closed loop.

- Yes injectors are DELPHI 17104487 and in my injector chart they are 50lb/hr injectors.

My findings

What I found was in the first 9 files (Street tunes) Min coolant temp for closed loop was set at 51.5 Deg. C. Min BLM Value 125, Maximum BLM 130, Min INT 80, Max INT 218. The scanner showed it went into closed loop fuel control at 51 DEG. C.

I broke out file 16 and MIN and MAX BLM and INT were the same, but MIN Coolant Temp for Closed Loop was raised to 151.25 DEG. C open loop fuel control as per scanner and file as you stated.

I am thinking of putting the emulator on it and running file 3 or 4 and put it into open loop and see what happens, or is it possible to have you look at the file and see if someone has altered it? Its to strange that the first 9 files go against everything I have read and now what you said you did.

Again I want to thank you for shedding some light on my questions, and please give me your thoughts on my findings.
 

smeagol

Active member
Re: stg ultimate info

Ah, so you have one of the chips setup for heads/cam. These were different than the 50# Ultimates for stock motor.

Some more tangential storyline, to add some color to the situation. Some of it I'm sure you're aware of, others not so much. The syty is a speed density beast, and most any of the calibrations based on a stock-ish motor don't work well as soon as you change the VE much. Especially so when you are talking about heads/cam changes. Turbo/intercooler/exhaust changes seem to be a bit more forgiving. Anyways, the stock computer is obviously more than capable of handling these mods with the right calibration. We had hoped we'd find some good recipe builds for those who were rebuilding motors and doing upgrades as far as with heads/cam. The recipes that came about were using L35 heads, Vortec heads, and mild cam upgrades. Problem was that everyone had their own little variations. Headwork, no headwork, slightly different cams, different valvetrains, 3 angle, 5 angle, 19 angle valve jobs, 1.5 rockers, 1.6 rockers etc. Anyways, we offered some calibrations that we hoped would be a good fit for a couple of these recipe builds. Worked ok on some, didn't work so well on others. I never was able to spend the amount of time I would have liked on these, and this was at a time when more and more people were getting into tuning syty's using the factory computer. I never was of the mind that one-size-fits-all calibrations were the answer, but many people don't have the time/means/resources for custom tunes. So they didn't progress much further, and many people using these calibrations ended up with custom tunes, or aftermarket standalones, or were content with what these calibrations offer.

Anyways, methinks you might have a chip layout like this: http://www.nwstp.com/tech//chipstuff/camheadchip.htm

I don't recall... did you guys mention what the build is for the truck in question?

I'll do my best to dig up the files for confirmation for you; I had a hard drive just crash recently that had my syty stuff on it. I have it all backed up, but it's not up online on my server for my easy perusal, and it's not something I access all that often :)
 

gearhead143

New member
Re: stg ultimate info

Ah, so you have one of the chips setup for heads/cam. These were different than the 50# Ultimates for stock motor.

Some more tangential storyline, to add some color to the situation. Some of it I'm sure you're aware of, others not so much. The syty is a speed density beast, and most any of the calibrations based on a stock-ish motor don't work well as soon as you change the VE much. Especially so when you are talking about heads/cam changes. Turbo/intercooler/exhaust changes seem to be a bit more forgiving. Anyways, the stock computer is obviously more than capable of handling these mods with the right calibration. We had hoped we'd find some good recipe builds for those who were rebuilding motors and doing upgrades as far as with heads/cam. The recipes that came about were using L35 heads, Vortec heads, and mild cam upgrades. Problem was that everyone had their own little variations. Headwork, no headwork, slightly different cams, different valvetrains, 3 angle, 5 angle, 19 angle valve jobs, 1.5 rockers, 1.6 rockers etc. Anyways, we offered some calibrations that we hoped would be a good fit for a couple of these recipe builds. Worked ok on some, didn't work so well on others. I never was able to spend the amount of time I would have liked on these, and this was at a time when more and more people were getting into tuning syty's using the factory computer. I never was of the mind that one-size-fits-all calibrations were the answer, but many people don't have the time/means/resources for custom tunes. So they didn't progress much further, and many people using these calibrations ended up with custom tunes, or aftermarket standalones, or were content with what these calibrations offer.

Anyways, methinks you might have a chip layout like this: http://www.nwstp.com/tech//chipstuff/camheadchip.htm

I don't recall... did you guys mention what the build is for the truck in question?

I'll do my best to dig up the files for confirmation for you; I had a hard drive just crash recently that had my syty stuff on it. I have it all backed up, but it's not up online on my server for my easy perusal, and it's not something I access all that often :)

I do understand no one tune works for all, I have been dealing with this since I got into tuning a long time ago, back when a HEX editor (something I don't use much any more)was all there was, and you had a pile of 2732A proms and just about wore out a eraser and programmer to get one tune the way you wanted it. Ahh those were the days, NOT!

I am not on the PC that has the files to look and see if the link you posted matches, but will check it out tomorrow when I get home. I do most of this work where I have peace and quiet so I don't get interrupted every 5 minutes.

The build is a McCoy Performer Plus crate engine, headers, and a Innovative 60-1 turbo.

It would be great if you could retrieve these files for confirmation.

Thanks again for you time and input.
 

smeagol

Active member
Re: stg ultimate info

If you are going to be spending some time on the truck, it's probably best to just start with a Code59 bin and do some tweaking. Might find someone with a good calibration to start from as well.

Do you know the cam specs on the motor?

I do understand no one tune works for all, I have been dealing with this since I got into tuning a long time ago, back when a HEX editor (something I don't use much any more)was all there was, and you had a pile of 2732A proms and just about wore out a eraser and programmer to get one tune the way you wanted it. Ahh those were the days, NOT!

I am not on the PC that has the files to look and see if the link you posted matches, but will check it out tomorrow when I get home. I do most of this work where I have peace and quiet so I don't get interrupted every 5 minutes.

The build is a McCoy Performer Plus crate engine, headers, and a Innovative 60-1 turbo.

It would be great if you could retrieve these files for confirmation.

Thanks again for you time and input.
 

gearhead143

New member
Re: stg ultimate info

If you are going to be spending some time on the truck, it's probably best to just start with a Code59 bin and do some tweaking. Might find someone with a good calibration to start from as well.

Do you know the cam specs on the motor?

Sorry about not getting back, but has been a great and scary time. We were blessed with a new Grandson on Friday, but my daughter had major complications after the birth. She is stable now and should be able to go home Tuesday.

On the cam. McCoy has not been very cooperative on supplying a grind number. All they would say is the it is a Crane 430 grind, and would not give a grind number. They said they don't keep any build records of their crate engines.

I did look at bins 12 through 16 and they were all in open loop. I did run it in file 12 and was a little lean at idle ( no drive) off idle was in the 13.6 to 14.5 range. Tip in from idle was lean. I think this is a doable starting point on the street OL file.

I did noticed one thing. When I compaired files 12 through 16 I didnt find anything on boost changes, just timing in the main table. Am I missing a table or constant that TC doesn't have listed? If so let me know so I can get them added.
 
Top