Still have knock ....

Mike

New member
I just finished installing an AFPR, 160* thermo and replaced the IC metal lines with rubber and i'm still having a knock issue. The FP is set to 50 with the vacuum line off, plugs were gapped to .032 and changed last week, cap rotor and wires all changed less than 2k miles ago. Here is my newest DM file http://www.mediafire.com/?csejxwuibuy

The list of mods are in my signature. What do i do next?
 

supersports10

New member
Re: Still have knock ....

what chip do you have??? is it seated properly???

the afr is set at a constant 10.1 :eek: :eek: :eek: :eek: that is pig rich!!!!

you cant be getting better than 10 mpg...

it should be 14.7:1 at cruse, and around 12:1 under boost.

still looking,....more questions to come.....
 

supersports10

New member
Re: Still have knock ....

you never hit more than 10 lbs of boost the whole run.....should be 14-15.

as pig rich as this truck is, it would run like a raped ape on e-85 ethanol!!!
 

Mike

New member
Re: Still have knock ....

I have the ultimate chip for stock injectors. It is set on T1-15 but since i have so much knock it wont let me run over 10psi of boost. The timing is also set to 0. Maybe i should try to run the stock chip and a 2 bar map to see if that changes anything?
 

supersports10

New member
Re: Still have knock ....

i have never seen an ultimate chip be stuck on 10:1 afr.... maybe the ecm is in "limp home" mode.
 

Mike

New member
Re: Still have knock ....

I'm not really sure what that is. Did you want to take a look at a DM run before i had the AFPR and 160* thermo in?
 

turbodig

Active member
Re: Still have knock ....

supersports10 said:
what chip do you have??? is it seated properly???

the afr is set at a constant 10.1 :eek: :eek: :eek: :eek: that is pig rich!!!!

you cant be getting better than 10 mpg...

it should be 14.7:1 at cruse, and around 12:1 under boost.
..

An ultimate will do that if it's wide-band patched and no wide-band is present.


IATs are really high, unless it's 90 degrees plus outside.

Making some big generalizations from the narrow-band o2, I'd say it's too lean. Which I'd expect, given that the chip you have isn't set up for the turbo that you have.
 

Mike

New member
Re: Still have knock ....

Why wouldn't i be able to run the ultimate with an RPM stage 1? Its not too much bigger than the stock one. The ultimate calls for the base FP to be at 50. Should i try to turn it down a little?
 

WyoSyclone

Active member
Re: Still have knock ....

Mike said:
Why wouldn't i be able to run the ultimate with an RPM stage 1? Its not too much bigger than the stock one. The ultimate calls for the base FP to be at 50. Should i try to turn it down a little?

As Dig said, it looks like it's probably running lean... turning the fuel pressure down will make it run even leaner. I've got the Stage1 on my Sy with 40lb injectors (bigger than stock) and I've had to do a lot of tuning to get things close to being correct. The Stage1 is simply moving more air than the stock turbo.
 

turbodig

Active member
Re: Still have knock ....

Mike said:
Why wouldn't i be able to run the ultimate with an RPM stage 1? Its not too much bigger than the stock one. The ultimate calls for the base FP to be at 50. Should i try to turn it down a little?

This seems to be the biggest thing that people don't understand about chips, and how our engine management system works-

If you change something, and don't change the chip, something will be off.

In the case of the ultimate, the one you have was set up for a stock motor, and a stock turbo. You added a larger turbo, which moves more air, but the chip didn't change. It thinks it's still getting the same amount of air.

This isn't just true of the ultimate, it's true of virtually any chip that you'd buy from anyone.

You can buy a chip from people who will sell you a chip for x injectors, turbo y, and cam z.
Even if that matches what you have, it's a complete crap shoot as to whether or not it'll actually work.

Unless you sent someone a data file of how your truck runs, and they send you a chip based on that data (and usually several repetitions of this), you're not going to get something that will work well.

Some people get lucky, and an aftermarket chip will work with what they happen to have. This is by far the exception, not the rule. Maybe 5% of the time, at the most.

This is why people are slowly coming around to the truth, that the only way to fix it right is to tune the chip to what you have. (Either by doing it yourself, or paying someone to do it)

As an aside, trying to use fuel pressure to change fuel is liketrying to fill a 55 gallon drum with a shot glass. If it's close to where it needs to be, you can do some good, but if it's waay off (which it usually is) you can't do enough to effect it.
 

Mike

New member
Re: Still have knock ....

Who on here could burn me a chip? I would rather pay someone to do it than try it myself since i dont know much about the subject.
 

Flyin Ryan

hated cuz he drives fords
Re: Still have knock ....

Mike said:
Who on here could burn me a chip? I would rather pay someone to do it than try it myself since i dont know much about the subject.

Look to post #12, that's the tuning guru
 
Top