Switching to 75#ers...

SCWolverine

New member
Getting ready to swap injectors (and drivers) and start tuning. Between the excellent fuel and boost stickies here and Digs "Step test" on 59.org, I feel I've got a bead on what's involved to smooth things out, just want to be sure I'm starting in the right ballpark. First question (there'll be more) is regarding fuel pressure, understanding I'll have to do what I gotta to get it running (bin tweaking and initial FP), what FP should be my target when I get the other things in line? Build below, nothing crazy boost wise. Thanks.
 

JSM

Active member
Re: Switching to 75#ers...

You don't need the high FP typically run on stock injectors. 42# base should be fine.

Also read over the wiring stuff on code59, with big injectors you really should change to true peak and hold.
 

SCWolverine

New member
Re: Switching to 75#ers...

Thanks for the input Jeff, shouldn't be a problem. Swap drivers, add the sense resistors and switch to the Sunbird wiring config, am I missing anything? Seems there is some degree of uncertainty in most of what I (mis?)read about this change, or maybe it's just that late.
 

blk00z28

Forced to by choice
Re: Switching to 75#ers...

Not to question your build or anything, but why are you making such a large jump from stock injectors to 75#'ers? Why not just go with 50's?
 

SCWolverine

New member
Re: Switching to 75#ers...

Question away, no offense taken. Just thinking that when it comes time to go through the bottom end and get serious that's one less thing I'll have to RE-do. 50#s and alky would probably go farther than I'll need, but this way I'll always have some headroom (and not have to rely on alky).
 

turbodig

Active member
Re: Switching to 75#ers...

SCWolverine said:
Question away, no offense taken. Just thinking that when it comes time to go through the bottom end and get serious that's one less thing I'll have to RE-do. 50#s and alky would probably go farther than I'll need, but this way I'll always have some headroom (and not have to rely on alky).

Personally, I would have gone with the 60's. Much more fuel capacity than most people will have the engine to run (up to 70-80# with enough fuel pressure), and no driver conversion issues.

Just my .02.
 

SCWolverine

New member
Re: Switching to 75#ers...

turbodig said:
Personally, I would have gone with the 60's. Much more fuel capacity than most people will have the engine to run (up to 70-80# with enough fuel pressure), and no driver conversion issues.

Just my .02.

You're right, but I didn't (no further reasoning). The driver/sense resistor rework on the board is no problem, and from what I understand P&H is gooder anyhow (even if not necessary). I'm still looking to connect a few dots regarding the wiring changes (Sunbird). My summary, questions...

Connecting D5 to D6, and C13 to C15 create the sense current for each injector driver.

C11 and C12 are common (syty), which we don't want. So? Tie 468 (DK GRN) to C10 (per the SB diagram)?

Shaw's page mentions and shows an internal jumper on the board (connector), is this to get the desired 2nd output to pin 10?

Is there more to it (as far as physical changes needed)? I've not been able to do as much studying as I'd like, but I'm getting there (or at least far enough to come up with more questions).

Always appreciate your .02 dig, thanks for all your work/knowledge (same w/ JSM).
 
Last edited:

turbodig

Active member
Re: Switching to 75#ers...

SCWolverine said:
You're right, but I didn't (no further reasoning). The driver/sense resistor rework on the board is no problem, and from what I understand P&H is gooder anyhow (even if not necessary). I'm still looking to connect a few dots regarding the wiring changes (Sunbird). My summary, questions...

Connecting D5 to D6, and C13 to C15 create the sense current for each injector driver.

C11 and C12 are common (syty), which we don't want. So? Tie 468 (DK GRN) to C10 (per the SB diagram)?

This was discussed on code59 a bit already.

If it were me wiring it up, I'd use both C10 and C11, 3 injectors a piece. This would imply a bit of re-wiring, as the stock injector harness goes to all 6. Find a chunk of harness out of any non-sequential V6 (any port 2.8/3.1 that uses a '730 should have one).

I see a lot of people that put both injector drivers in, and then saturate just the one by using the stock SyTy wiring. Makes no sense. (no pun intended)

I'm not aware of many (any?) set up this way. I think most that are running big injectors are probably saturating, and the ones that are running P&H correctly are hanging all 6 off 1 driver.

I don't think anybody would see the ECM heating issues if they were wired properly. There are 2 drivers in the system, you might as well use them.

Part of me wonders about running saturated injectors off both drivers. I would think the open/close speed should improve, since there's less of an inductive load hanging on each driver.

Later,
 

SCWolverine

New member
Re: Switching to 75#ers...

turbodig said:
This was discussed on code59 a bit already.

If it were me wiring it up, I'd use both C10 and C11, 3 injectors a piece. This would imply a bit of re-wiring, as the stock injector harness goes to all 6. Find a chunk of harness out of any non-sequential V6 (any port 2.8/3.1 that uses a '730 should have one).

That is the piece of the puzzle I've been missing, it had crossed my mind, but I figured I would be able to verify it somewhere (but couldn't).

turbodig said:
I see a lot of people that put both injector drivers in, and then saturate just the one by using the stock SyTy wiring. Makes no sense. (no pun intended)

I'm not aware of many (any?) set up this way. I think most that are running big injectors are probably saturating, and the ones that are running P&H correctly are hanging all 6 off 1 driver.

I don't think anybody would see the ECM heating issues if they were wired properly. There are 2 drivers in the system, you might as well use them.

Amen to all these points. I know Bill Shaw's page does a bang up job documenting the driver/sense resistor details, but it seems like all the other threads stop there or add "rewire to the Sunbird schematic" with no hint of the specifics that entails. I'll see if I can produce some decent notes/pics of the wiring side of things as I go, hopefully producing the last bits needed for a diyer.

I am assuming that splitting the injectors to 1/3/5, and 2/4/6 would be acceptable (?), or should it matter?

As always, thanks for your insight Dig.
 

10secTy

Sy-Ty builder and Tuner
Re: Switching to 75#ers...

I split it up using the sunbird wiring and added a extra pin on the ecm for ground.

It did see a increase in the amount on PW I could run at idle and High vacuum low PW areas of the tune.

Did I do it to any other trucks? No I could get the trucks running saturated mode to run just as well as peak and hold. So basically I just determined that it was not worth all the work unless you are doing it your self for your own truck. Even then with a good tune you will be the only one that know the diff because you see the PW on datamaster.

Nolan
 
Top