SyTy Downpipes

MikeRenz

not stock
I'd like to see a 1pc 3" dp for the no-a/c people. Less bends required and could take up more space....and probably stay out of the way of all the plugs w/ no problem.
 

UNIsackV6

Member
What about using 3 inch flexible stainless?? Depending on your needs you could easily buy different lengths, say get rid of the cat and go full 3 inch from the exhaust forward (most aftermarket exhausts are 3 inches anyways) until you are right by the turbo and here get a stainless 3 inch 45 degree bend like I did and then you could put any end you want on it. You could reduce it to 2.5 inches to connect to a stock set up, keep it 3 inches and connect to an aftermarket turbo, my 45 degree pipe has a V-Band clamp to the turbine housing. The beauty of this set up are as follows as I see it.

1) Flex stainless is tough won't rust.
2) Its FLEXIBLE!!!! want to get to the plugs? Just disconnect the downpipe from the exhaust housing and move it out of the way!!!
3) You can put any kind of downpipe to exhaust housing end on it.
4) If you switch turbo's in the future you don't have to start all over, just mod the connection to fit your new exhaust housing.
5) At 3 inches it undoubtedly will outflow the stocker or the KennyBall.
6) Kamikazee Ty has it and works great. Yes he had it with the AC.

Just my six sence err 6cents...my set up is all flex except for the 45 degree pipe to the turbine then it goes all the way back to the muff...ler and thats it. I've taken my entire exhaust system off from turbine all the way to the turndown on the muffler in under 10 minutes, why would one want to do this? Don't really recall why I did it but it made life way easier.
Burnes Stainless is good place, but do a search there are dozens of places selling the stuff....good luck...
 

ghettosled

SYTY SUPERSTORE
For those who care, I have some downpipe jigs setup for KB and stock/atr headers.

For KB headers I have a 3" mandrel bend 2 piece downpipe. It is connects with a v band clamp in the middle and does not leak. It is available in stainless or mild steel, and will clear ac with turbos up to 88mm. Plug change is a breeze.

downpipe.jpg


For ATR/Stock headers I have a 3" downpipe mandrel bend 2 piece with v band clamp also. Stainless also available. Plugs are easy to change and it also works w/ or w/o AC(We have two versions). We use the PTE housing for best seal and turbo placement, and machine it to work properly with an external wastegate. This is the preferred setup to use if you are running high flowing big shaft turbos. This setup is like the ATR one, but we use 1.75" wg tubing, and machine the wg port another .5" over the standard pte size, plus you eliminate the 3-4 bolt adaptor which WILL leak. Expect rock solid boost control!

ardp1.jpg


If you want internal wastegate, the pte is the way to go.

ptekit.jpg


A one piece downpipe in 3" would be impossible to install/remove, and E-Rue there is no point to having a 3.5" downpipe if you are going to neck it down at the cat or muffler. It must stay the same or get larger.
 

UNIsackV6

Member
Wait....Mike's stuff sux :wink:....just kidding he's absolutely right he has a solution for you either way you want to go...just trying to give everyone options, really Mike has most everyone covered...I have a few parts from Mike, most importantly my headers which are top fucking notch...he's my favorite vendor no doubt....he is defintely the most trusted in my bookl....Ryan
 

E-Rue

New member
ghettosled said:
E-Rue there is no point to having a 3.5" downpipe if you are going to neck it down at the cat or muffler. It must stay the same or get larger.

it only needs to stay 3.5" long enough to make it to the dump. besides, i have heard many arguments about exhaust not needing to stay as big, as the distance form the turbo increases and the exhaust temp comes down.

i see what your saying tho. guess it would help if i explained more...... i have what is probably the first BIG turbo PTE has done with the sy/ty housing. its a PT74 Q-trim, with syty housing, and internal gate. i dont have it installed and running yet, but ill keep ya posted. i dont have AC, but im assuming if it clears everything and is an easy bolt-on, that this will be a popular turbo for our group in the future.

e
 

ghettosled

SYTY SUPERSTORE
yeh we have done a couple setups with 76 Q and R trims in the PTE housing, but we ran external wastegates on them. You can choose a 60-1 housing for better clearance over the ts04. Also a dual ball bearing or water cooled center section will make the backplate stick out further away from the ac bracket (now you can loosen the bolt with ease)

Obvioulsy Erue, you dont have to worry about this.

Keep us posted on how the internal works out, and what are you doing for boost control?
 

FLSY2730

New member
ghettosled said:
yeh we have done a couple setups with 76 Q and R trims in the PTE housing, but we ran external wastegates on them. You can choose a 60-1 housing for better clearance over the ts04. Also a dual ball bearing or water cooled center section will make the backplate stick out further away from the ac bracket (now you can loosen the bolt with ease)

Obvioulsy Erue, you dont have to worry about this.

Keep us posted on how the internal works out, and what are you doing for boost control?


The turbo you sold me has the precision housing , correct? Thats why i also have your downpipe, right?
 

ghettosled

SYTY SUPERSTORE
Jack, you have the modified pte housing that is used with our downpipes and external wastegate. now get to the track and get some timeslips !!!!!
 
would someone make this black and white for me, as apparently my iq is down at the moment.
i have a 20g, and oem manifolds, both of which i am keeping.
everything is coming apart very soon for new heads, extrude honed manifolds. keeping 20g (KB jimmy 1).
can someone sell me a big ass downpipe (i have a/c and am keeping it) that'll work? i am staying internal wgate for ultimate to control boost. i am gonna port the wgate when it all comes off for the heads.
so, someone want my money? - mandrel, stainless or coated, 3" adapting to teh mitsu outlet?
 

ghettosled

SYTY SUPERSTORE
porting isn't going to help much. You need to machine a larger hole and install a larger swing valve if you intend to have perfect boost control with internal wastegate..
 

ghettosled

SYTY SUPERSTORE
I know richard chan was doing these awhile back.. Other than that, I would try some of the DSM guys. Extreme turbo, hann racecraft etc.
 
i've not heard rc's name in a while.
but i'm a dealer for hahn, so thanks a lot - i never think about the ricers...least, try not to...
appreciate the tip!
mike
 
The actual puck or swing valve is plenty big, nearly as big as TurboBuick. It's just the little ass downpipe and the two 90 degree turns for the wastegate exhaust is the restriction. Remove the service port and make a 3" downpipe and you'll have perfect boost control, I guarantee.

You might ask Dig how he can control boost on his setup.
 

just a 6

R.I.P MyClone
I agree on this one, i rather fight it once and have no leaks then easy install with possible leaks in the future.



rockvillespeed said:
i'd way rather fight hard once then deal with recurring leaks from a 2 piece, imo...i hate doing things twice, and leaks REALLY piss me off
 

ghettosled

SYTY SUPERSTORE
I would imagine that for a 3" one piece dp you will either need a lift or you will need to remove your fender and fenderwell. And IF it comes out in one piece you will probably not be able to access some of the spark plugs. We've tried on a few setups and its really difficult.

Use a v band clamp.. they dont really leak. The slip over tubing with t clamp will leak from time to rime.
 

10secTy

Sy-Ty builder and Tuner
PTE housing with dual ball bearing Garret T-76 Q trim. Notice that the PTE style internal wastgate is 3.5"
Flapper valve is 1.5" and wastgate hole is bored out to 1.4" instead of the 0.875" that comes stock on the PTE housings.
MVC-017F.JPG

MVC-012F.JPG


Nolan
 
Top