tuning advice

randy merritt

Donating Member
After a recent failure and rebuild, I am starting to tune on Code59. There is an AWD chassis dyno close to me, and I think I have the basics down. I have been offered help by board members, but I do not want to put anyone out for my project. My first question: is it necessary to read plugs during tuning if the dyno has indicated MBT? My plan is to disable all enhancers (F77x, anything to do with cold, hot, etc.) and follow basic tuning methods. The truck has good general driving qualities, but I have not ran the boost up beyond 15 or so psi. I am running a pretty good .bin by picking and choosing parts of others posted or given. Is there something I am missing by just following basic boost tuning methods? (i.e. steady state up to mild boost, adjusting AFR for each block of RPM, then adjusting advance to reach MBT, then ramp runs with gradual boost increase using the same methods)

Thanks in advance.
 

Quickstop [UK]

Combating adversyty.
Re: tuning advice

When is your alky coming on?

I think with alky it's a bit different in that you aim for a rich AFR of about 12.0 and then tune using the knock detector for MBT (max brake torque?) by advancing the timing. I could be mistaken.

Plug reading will tell you how far advanced/retarded you are but if you advance until you get knock then retard then you're getting the same result I think.

Disclaimer: all of this is based on my reading, not experience.
 

randy merritt

Donating Member
Re: tuning advice

When is your alky coming on?

I think with alky it's a bit different in that you aim for a rich AFR of about 12.0 and then tune using the knock detector for MBT (max brake torque?) by advancing the timing. I could be mistaken.

Plug reading will tell you how far advanced/retarded you are but if you advance until you get knock then retard then you're getting the same result I think.

Disclaimer: all of this is based on my reading, not experience.

My understanding is that the Alky will be used to achive MBT (minimum best timing or maximum brake torque) only when my pump gas will not handle the boost and achieve MBT. Right now my turn on is 10psi, but I plan on disabling the Alky until needed. I plan on tuning for 11.2 or so AFR at WOT without Alky, and 10.8 or so on Alky. Cruise for around 14.7 or slightly leaner if no knock. I'm not concerned about gas milage, just want a safe, fast play truck. Not an expert, but I do read posts and books a lot before doing anything stupid.
 

randy merritt

Donating Member
Re: tuning advice

BTW, I met several of you guys (Brits) when I was in Saudi Arabia during the gulf war. The Brits had compounds that allowed drinking of adult beverages. I was lucky enough to visit a few times (2 or 3). everyone asked me why I had a funny accent, and I asked them the same. Great folks that made a hard time a little easier.
 

Quickstop [UK]

Combating adversyty.
Re: tuning advice

Did you make it to Ras Tanura? We lived in Saudi Arabia, hence the Ty, and I was there for the Gulf War.
 

randy merritt

Donating Member
Re: tuning advice

Another question after some thought. Is it dangerous to tune to MBT given the unequal flow qualities of the sock manifold? I could see a benefit of plug checking the lean cylinders if there is a danger.
 

qbnkiller

Conflaguration Specialist
Re: tuning advice

Hi Randy;

As I have mentioned previously, reading your plugs is essential to know exactly what is happening inside each cylinder. Going by just a knock sensor, O2 sensor, or what others say should be will never get you to where the engine wants to be. There are things you can see while tuning on the dyno, but plug reads should be a part of the procedure.
 

randy merritt

Donating Member
Re: tuning advice

Hi Randy;

As I have mentioned previously, reading your plugs is essential to know exactly what is happening inside each cylinder. Going by just a knock sensor, O2 sensor, or what others say should be will never get you to where the engine wants to be. There are things you can see while tuning on the dyno, but plug reads should be a part of the procedure.

I agree, and I understand about reading the plugs to achieve the best AFR, but I was going to tune the timing on a chassis dyno where the torque curve could tell you where MBT is at. I really don't know a whole bunch about this, but wouldn't MBT be your best timing advance? (of course with monitoring knock via plug read) Thanks.
 
Top