Tuning Help

Nitrous

New member
Re: Tuning Help

WyoSyclone, I read about your tune on code59 and will download it tonight when I have some time to play. I also wanted to let you know I have the Kenne Belle chip that came with the 40lb injectors but always heard there was knock retard issues withit. I'm not sure about OBDI but OBDII we can pull the info out of the pcm if it isn't locked. Are OBDI chips locked? I'd like to compare your tune to the Kenne Belle if at all possible.
 

Nitrous

New member
Re: Tuning Help

Here's what I have and the wires to the right go to the controller. Looks like I have the G3 switching bank already so it will come in handy once I get the tune right. I've got 2 new chips that came with my tuning hardware so should be able to load Rob's bin one of the chips and just swap it with the one I'm currrently running right?
 

Attachments

  • DSC01472.jpg
    DSC01472.jpg
    33.2 KB · Views: 0
Last edited:

syty9933

New member
Re: Tuning Help

i had the same problem installing it with vista but all you have to do to get it to work is to right click the datamaster icon got to properties, then click on the compatibility tab. Then it will give you the option to run the program as windows xp. With 20 free trials and no authoruzation code
 

Nitrous

New member
Re: Tuning Help

Well, the chips that Moates sent me are too smaller than what's in the G3 and smaller than my Burn 2. but are the same size as the ribbon cable that goes into the Ostrich 2.0.
 
Last edited:

Nitrous

New member
Re: Tuning Help

i had the same problem installing it with vista but all you have to do to get it to work is to right click the datamaster icon got to properties, then click on the compatibility tab. Then it will give you the option to run the program as windows xp. With 20 free trials and no authoruzation code

I tried that but it kept asking for an auth code for some reason. I'm going to uninstall the program and install it again to see what happens . I've tried the Disk from TTS and the down load both. Maybe there's a conflict because I didn't uninstall before loading the 2nd download.
 

turbodig

Active member
Re: Tuning Help

Here's what I have and the wires to the right go to the controller. Looks like I have the GP3 switching bank already so it will come in handy once I get the tune right. I've got 2 new chips that came with my tuning hardware so should be able to load Rob's bin one of the chips and just swap it with the one I'm currrently running right?

That's a Moates G3. The moates switcher will plug right into that.
 

Nitrous

New member
Re: Tuning Help

I was able to finally log some data from datamaster! :D The funny thing is I went to the car show last night and someone must have messed with the factory boost controller since it's by the battery now and the wastegate opened at above 26 psi and blew smoke everywhere LOL. I pulled over to see what had happened and saw the vacuum line was off. I put it back on and was back to maintaining 16-17 psi. I'm glad I didn't mess anything up..............................:oops:

LT FT are 128
ST FT stay close to 100
Inj DC idles 2.0 and got as high as 88
BPW 0.70 w IDC 1.2

running pig rich with AFR 10.6
 

Nitrous

New member
Re: Tuning Help

Dig, should I save the bin on the chip I currently have and write Robs to the same chip?
 

Nitrous

New member
Re: Tuning Help

Ok, here's where I'm at. I saved the bin that was on the chip in the G3 and wrote Robs bin to the chip. I put everything back in the pcm and had problems getting a connection with datamaster but my check engine light came on and idled 2500 rpm but the afr was a l;ittle better at 11.0. When I was driving and tried WOT the AFR went 17 plus and I idled back home and put the original bin back on the chip and still had the same problem. I just happened to pull the moates controller off the GP3 and the original bin runs better than it did before but still not perfect but a lot less fat at idle. I'm not sure if the controller loses it's memory when unplugged but I'm going to put Robs bin back on in the morning without the controller and let you know what it does. Here's a picture of the old and new turbo before installation. Notice the compressor wheel size and inlet and the turbine exhaust larger sizes The exhaust opening is almost 1/2" larger and the inlet is 3" now. BTW, it's all Mitsubishi and the compressor housing is almost 1" larger in diameter with plenty of clearance on the sides to keep it factory looking.
 

Attachments

  • DSC01438.jpg
    DSC01438.jpg
    48.8 KB · Views: 0
  • DSC01439.jpg
    DSC01439.jpg
    54.2 KB · Views: 0
Last edited:

Nitrous

New member
Re: Tuning Help

Ok leaving the EX remote unplugged the tune works fine. I've got Robs 40# tune running and I still get AFR 10.7 at idle but normal driving conditions part throttle it's about 12.8 but when I go WOT it leans out to 15.7 AFR I haven't logged any data because the G3 and remote controller won't make connection to the PCM until you disconnect the controller which I thought was strange but I'm learning. I went to put the multitune back in but it only loads the stock bin on the chip. If I read correctly on Powertune plus.com you have to load each individual tune onto the chip in order for them to work with the EX Remote settings.
 

Nitrous

New member
Re: Tuning Help

Ok leaving the EX remote unplugged the tune works fine. I've got Robs 40# tune running and I still get AFR 10.7 at idle but normal driving conditions part throttle it's about 12.8 but when I go WOT it leans out to 15.7 AFR I haven't logged any data because the G3 and remote controller won't make connection to the PCM until you disconnect the controller which I thought was strange but I'm learning. I went to put the multitune back in but it only loads the stock bin on the chip. If I read correctly on Powertune plus.com you have to load each individual tune onto the chip in order for them to work with the EX Remote settings.
 

wildphil

I Love My Ty's
Re: Tuning Help

When you first started the truck with Robs bin did you adjust table f28 to get your idle afr to about 14.7? If not do that first thing after you get the truck to operating temp. After that then you will have to do a data log and start to adjust afr. This bin is just a start. The afr will have to be adjusted to your truck. That is done by data logging then adjusting afr. We will tell you how to do that if you need us to. When you first start logging drive very easy.DO NOT GET INTO BOOST. All normal driving is tuned b4 boost driving is set.
 

WyoSyclone

Active member
Re: Tuning Help

I've been away most of the weekend... another thing is fuel pressure. I have my Sy set up to run 48lbs static pressure (truck off, key on, pump primed). If your pressure is lower or higher you may want to set it at 48 just to make things easier. WildPhil is right... adjust f28 to get it to idle at 14.7 then go out for an EASY run. If all looks good just take the rpm and throttle a little higher on each drive, logging as you go. Since we're running the same injectors it should be close.

Do above, then if you want to email me a DM log I could look at it tonight.... address is:
rputman at bresnan dot net.

...Rob
 

Nitrous

New member
Re: Tuning Help

No I didn't adjust the tabl;e because this is new to me as far as tuning S/W. I would love an idle of 14.7 Where do I find that table in Tunerpro RT?
 

WyoSyclone

Active member
Re: Tuning Help

No I didn't adjust the tabl;e because this is new to me as far as tuning S/W. I would love an idle of 14.7 Where do I find that table in Tunerpro RT?

It's in the 'tables' section under fueling, towards the top. double click on it, and the table will appear on the right. click on graph button, and the graph should show up. click and hold down with your left mouse button and draw a box around all of the values. then release mouse button and click and hold on one of the blue dots that appear on the graph. Pull the mouse down as you hold the left button and you can drag all the values lower at once. Take it down about 5 or 10 points, burn the new BIN, then go try and see how much it changed. Shouldn't take more than a couple of times to get it very close.

I'll be around most of the night so I'll keep checking back here.
 

Nitrous

New member
Re: Tuning Help

Ok, Idle at temperature is 10.7 AFR with the wideband. I know this sounds funny but I don't see fueling anywhere in the tables section. I'm reading your bin as an XDF file is this correct?
 

WyoSyclone

Active member
Re: Tuning Help

At the top of the TPRT screen it should say: "TunerPro RT - then the BIN name / then the XDF file name.

Does your screen show that?
 
Top