Tuning Help

wildphil

I Love My Ty's
Re: Tuning Help

It is kinda fun. I really started enjoying it once I knew enough to do a log and edit the bin.

There is still alot for me to learn. But now I am not afraid to tune like I was at first.

Keep in mind your afr will not always be 14.7. You will need to have more fuel at higher rpm and also in boost.

If you open up the F29_AFR table and look at the cells you will notice the numbers for the AFR get richer as the rpm and boost get higher.

I am ready to start tuning my truck for alky. I have been doing a little work to it that has kept me away from tuning. But next week I should be able to start that.

Keep after the tuning. You should be able to get your truck to run strong. Just take it easy and go slow.
 

Nitrous

New member
Re: Tuning Help

Thanks man, I just logged with DM but I only have 6 free logs left until my authorization number is in. :( Steve's still helping me.
 

wildphil

I Love My Ty's
Re: Tuning Help

Tuning is buy far the best performance uprade anyone can do.

It makes the stock trucks run there best.

And putting big turbos, cams and alot of other parts on these trucks usually makes them worse. Unless the truck has the correct tune for that truck.

I believe it is much better if the owner will learn to tune. There are enough people here for help.

You will be happy you are learning. When you get your truck running like you had hoped it would.
 

turbodig

Active member
Re: Tuning Help

Ok, here's where I'm at. I saved the bin that was on the chip in the G3 and wrote Robs bin to the chip. I put everything back in the pcm and had problems getting a connection with datamaster but my check engine light came on and idled 2500 rpm but the afr was a l;ittle better at 11.0.

Rob's bin won't burn onto the chip that you had in the G3, at least not directly.

I'm sorta lost in this thread.... are you now flashing chips and using a different moates board, or the ostrich, or ? What's running in the truck now?

There are specific "rules" about what size/type of flash device (PROM) you can use with a given moates adapter. Plug the wrong one into the wrong adapter, and you can end up with smoke.
 

undrcvr_ty

Its just a blazer...
Re: Tuning Help

Ok, here's where I'm at. I saved the bin that was on the chip in the G3 and wrote Robs bin to the chip. I put everything back in the pcm and had problems getting a connection with datamaster but my check engine light came on and idled 2500 rpm but the afr was a l;ittle better at 11.0. When I was driving and tried WOT the AFR went 17 plus and I idled back home and put the original bin back on the chip and still had the same problem. I just happened to pull the moates controller off the GP3 and the original bin runs better than it did before but still not perfect but a lot less fat at idle. I'm not sure if the controller loses it's memory when unplugged but I'm going to put Robs bin back on in the morning without the controller and let you know what it does. Here's a picture of the old and new turbo before installation. Notice the compressor wheel size and inlet and the turbine exhaust larger sizes The exhaust opening is almost 1/2" larger and the inlet is 3" now. BTW, it's all Mitsubishi and the compressor housing is almost 1" larger in diameter with plenty of clearance on the sides to keep it factory looking.

Where did you get that turbo?
 

Nitrous

New member
Re: Tuning Help

Rob's bin won't burn onto the chip that you had in the G3, at least not directly.

I'm sorta lost in this thread.... are you now flashing chips and using a different moates board, or the ostrich, or ? What's running in the truck now?

There are specific "rules" about what size/type of flash device (PROM) you can use with a given moates adapter. Plug the wrong one into the wrong adapter, and you can end up with smoke.

I just flashed the chip that was in the G3 which is larger than the one that came with the ostrich and other hardware. I have 2 smaller chips but they come back failed when flashing everytime. I do have an adapter that will plug into the factory chip and then the ostrich will fit into that. I need to figure out how to install my wideband for data logging since there's no I/O box that came with it like HPTuners but it does have 2 wires for data logging.05volts. it says to plug into the computer with a db9 cable but I didn't have any luck.

Quote:
Originally Posted by Nitrous
Ok, here's where I'm at. I saved the bin that was on the chip in the G3 and wrote Robs bin to the chip. I put everything back in the pcm and had problems getting a connection with datamaster but my check engine light came on and idled 2500 rpm but the afr was a l;ittle better at 11.0. When I was driving and tried WOT the AFR went 17 plus and I idled back home and put the original bin back on the chip and still had the same problem. I just happened to pull the moates controller off the GP3 and the original bin runs better than it did before but still not perfect but a lot less fat at idle. I'm not sure if the controller loses it's memory when unplugged but I'm going to put Robs bin back on in the morning without the controller and let you know what it does. Here's a picture of the old and new turbo before installation. Notice the compressor wheel size and inlet and the turbine exhaust larger sizes The exhaust opening is almost 1/2" larger and the inlet is 3" now. BTW, it's all Mitsubishi and the compressor housing is almost 1" larger in diameter with plenty of clearance on the sides to keep it factory looking.

I had a friend build the turbo for me.
 

Nitrous

New member
Re: Tuning Help

Anyone here ever tapped into their A/C pressure switch to log with a wideband in DataMaster? I know it's been done with LT1's and I need someway to tap in the 5v wire. My HPTuners has connections on the tuner box so I can hook a wideband up without having this issue. I'll do some searchoin here on the forums in the meantime.
 

WyoSyclone

Active member
Re: Tuning Help

Anyone here ever tapped into their A/C pressure switch to log with a wideband in DataMaster? I know it's been done with LT1's and I need someway to tap in the 5v wire. My HPTuners has connections on the tuner box so I can hook a wideband up without having this issue. I'll do some searchoin here on the forums in the meantime.

Don't quite understand what you're asking here... if you want to use your wideband to log with, you need to tap into the ECM, pins b9 and e14... there's a thread on here detailing how... I'll go find it then post the link in a bit.

edit... here it is.... http://www.syty.net/forums/showthread.php?t=48363&highlight=plx
 

WyoSyclone

Active member
Re: Tuning Help

Thanks Rob, I read that already but I wasn't sure because of the PLX-SM-AFR, I don't have that box with the digital AEM. Here's the digital wideband and matching boost gauge.

http://www.aemelectronics.com/Images/Products/Installation Instructions 30-4100.pdf

http://www.aemelectronics.com/Images/Products/Installation Instructions 30-4406.pdf

So it just looks like the 'white' wire from the wideband gets connected to the ecm pin e14. Power can come from a fuse tap at the fusebox and I would find a good ground over by the ECM. I wouldn't use b9 for a ground as that is used for signal reference, and not as a power supply ground.
 

Nitrous

New member
Re: Tuning Help

So it just looks like the 'white' wire from the wideband gets connected to the ecm pin e14. Power can come from a fuse tap at the fusebox and I would find a good ground over by the ECM. I wouldn't use b9 for a ground as that is used for signal reference, and not as a power supply ground.

That's what I was thinking I just wasn't sure what pin to hook it to. This is where I asked about the a/c pressure switch since I've heard of othere tuners tapping into the one othe wires and changing the config in DataMaster to WB and then setting up the linear range. Sounds like I can move forward, I just need my DM Auth code so I can use Vista.
 

Nitrous

New member
Re: Tuning Help

I took some time to read on some of digs posts. I'm pining the wideband into the ECM per his instructions and downloaded the patch and AEM wideband patch file. I might have a question or two when I load the patch but I'll probably start taking my posts to code 59 for reading.

Thanks guys!
 

Nitrous

New member
Re: Tuning Help

Just wanted to thank everyone here for helping me get through the AEM wideband issue and it took reading on digs site to get things going in the right direction and help from Rob on his 40lb tune. After looking at the Kenne Belle chip I can see why it's called the kaboom chip. AFR's at 16 plus at boost. No disrespect to their tuner but I'm sure hope it was a tune mistake. Rob said my AFR's look pretty damn good and I have some temperature issues to straighten out before I tune any further. I love the gas milege not driving around with 10.7 AFR LOL :rant: I finally figured out how all of the hardware works and you can't beat the ostrich. Once the tune is finished I can't wait to build an Ultimate for that tune since I have the G3 with LED controller.

Thanks again! :tup:
 
Top