Typhoon newbie with chip question

4rs fed

New member
So i was told i have an "ultimate chip"

it has a display and goes t115 and all the way up to t324 i think with val and sec features and also a lock i can lock the setting to.

anyhow, a freind of mine had a typhoon before and when he put his ultimate chip in, he forgot to put the stock chip on the back of the ultimate and he drove the car for about 4 months trying to figure out why the car would run funny and sometimes fall on its face.

well my typhoon does the same thing, and i pulled the computer out of the truck to see if the guy before me did the same thing.
here is the what was in my computer.

normal_IMG_0007.JPG


is that a stock chip? it doesnt look like one to me,

and i was under the assumption that you were supposed to run a stock chip with the ultimate. If you dont, what happens?

Thanks
sorry if the question is dumb, i am totally new to these trucks and am learning and searching, i didnt find a thread that fit me, so i am posting a new one.


Rob
 

Flyin Ryan

hated cuz he drives fords
Re: Typhoon newbie with chip question

Looks like a stock chip but turn it over and see what the lab says under the blue piece
 

SYO237

SyTy Registry
Re: Typhoon newbie with chip question

that is the stock memcal with the STG (Sy Ty Guru) piggyback ultimate. Contact 'turbodig" on here, he can tell you whats up
 

turbodig

Active member
Re: Typhoon newbie with chip question

Hard to tell without looking at the top of the MEMCAL.
Sticker on the MEMCAL should say AYBN,AYBM,BBZA,BBZB. THere's a couple of others, too, but not as common.

The chip itself doesn't have to be stock. The MEMCAL adpater only needs the white-colored half of the MEMCAL.

THe old ultimate boards are notorious for breaking pins off, bad solder joints. When that happens, they do what you describe.

They can be "remanufactured" if necessary.
 

Ty1642

Member
Re: Typhoon newbie with chip question

turbodig said:
THe old ultimate boards are notorious for breaking pins off, bad solder joints. When that happens, they do what you describe.

They can be "remanufactured" if necessary.

I'd never heard that before. My truck has been having the same symptoms for a while and I've been trying to figure out why.

Dig - do you fix them, or do you have 'good' replacements to sell?

Thanks
 

SBNova

New member
Re: Typhoon newbie with chip question

Just to let you know, because I dont think it got answered- the brown piece with the light blue cover is your stock "chip", actually called a memcal. The "chip" is under the blue cover.
 

4rs fed

New member
Re: Typhoon newbie with chip question

SBNova said:
Just to let you know, because I dont think it got answered- the brown piece with the light blue cover is your stock "chip", actually called a memcal. The "chip" is under the blue cover.


ok thanks

so basically that picture is useless and since i didnt look under the blue thing, i could not have my stock chip in there.
i thought the STG was the "chip" part, but i guess not
 

turbodig

Active member
Re: Typhoon newbie with chip question

Ty1642 said:
I'd never heard that before. My truck has been having the same symptoms for a while and I've been trying to figure out why.

Dig - do you fix them, or do you have 'good' replacements to sell?

Thanks

I repair them.. actually, re-pin them for moates boards. Gotta do some re-cabling, then reburn the chip to meet the moates address map. Done a few of 'em so far.
 

SBNova

New member
Re: Typhoon newbie with chip question

Your stock chip is probably in there. There's no need to take it out, and sometimes theyre lightly soldered in anyway. If you look at the aftermaket part of whats in you hand in that picture you'll note that the only portion of the memcal that gets "used" is the end thats opposite the chip. This is where the limp and knock portion of the memcal are. The "chip" portion is not even connected, so it wouldnt matter if it were in there or not. You probably have a cracked solder joint or some other problem as pointed out above.
 
Top