Ultimate Chip Install ?'s

AlaskaTy

New member
Somehow I lost the install instructions on one of my many trips out to see my car (it's been in the shop for way too long...engine's been here for 5 weeks and it's still not finished being installed.) I removed my ECU and took off the access cover (2 hex bolts) and found what I think is my chip. It has two clips on either side you depress to get it out and there is a blue cover piece with two large holes in it.
So here it is, the ultimate fits in there, but it fits in both ways. The surrounding circiut board is WAY too large for the blue cover piece to snap on. So my question is which way does the chip go in? There are some "spikes" (real technical huh?) that occupy most of one side. Should those face towards the wires that go into the ECU, or away? And does that blue piece ever go back on? TIA

Jason
 

sytyguy

Moderated User
It is A LOT easier than you're making it out to be. First off, go ahead and pop out your old chip. Do this by depressing the 2 release pins on each side of it simultaneously. It will lift up and you can pluck it out. Now, with your stock chip in your hand and the ECM part of the Ultimate in the other, you want to piggyback your stock chip onto the Ultimate. Take the Ultimate and look at the male pins off the side that look like something ought to plug into them. There is a notch in the board itself just beyond these pins....note this. Now take your stock chip and look at the female receptacle that plugged into your ECM. You will see a hump on one side. That "hump" fits into the notch on the Ultimate when you plug them together. Now, take your stock chip and "plug it into" the Ultimate making sure to line up all the male pins on the Ultimate with the female counterpart on the stock chip. Also, make you sure you have the stock chip turned properly to slide into the notch. When held upright, the stock chip plugs in sideways of the Ultimate.

Now, you should have a stock chip piggybacked by the Ultimate EPROM carrier. With this in hand, flip over the carrier and look at the bottom. You will see the same female receptacle that you saw on the stock chip. This fits into the ECM just like the stock chip did. *You may have to trim the left release pin (white in color usually) in order for the Ultimate carrier to seat properly. Just take a pair of wire cutters and snip the top part off (leave enough to push on in case you have to remove the Ultimate one day). With this modification done (if necessary), drop the Ultimate carrier (with stock chip attached) into the ECM. The cable from the Ultimate carrier to the box should be going towards the left, IIRC. You need to slide the Ultimate's female receptacle into the ECMs male pins with the same care as you did the stock chip to the Ultimate, minding the hump to notch relationship as well. When it seats properly (may take some force and wiggling to get carrier snapped down), you will see the release pins lock into place.

Verify operation of Ultimate by turning key on and observing display. It should have a readout on it. Toggle thru all the settings and verify working order. If the display reads nothing or the CE light flashes rapidly, recheck all connections and parts.

This should get you up and going. If you still can't figure it out, I'll grab the digi-cam and snap some shots of the procedure tonight.

HTHs

Michael
 

AlaskaTy

New member
Thanks sytyguy, I'm going out there within the hour to install both the chip and my deck. I have one concern though, when I bought my truck it had some stuff done. It had ATR 3" cat back, ATR aux IC, datamaster was showing it was running cooler than stock (~160) so I was wondering if the previous owner just got the ATR stage two done. Does anyone know if the pitbull chip is a replacement for the stock chip or a piggyback system like the ultimate? Another thing, I'm pretty sure datamaster was showing that I had a stock chip, like 9801 or something (I bet guessing randomly at the numbers doesn't help too much.)

Jason
 

smeagol

Active member
Good instructions Mike. Here's a pic that may help a bit (not high res, but oh well)

chipin1.jpg
 

sytyguy

Moderated User
You really want a stock chip to be piggybacked to the Ultimate, but I won't say it's CRUCIAL. I let a buddy use my Conley chip with his Ultimate years ago and it worked great. I don't think there's any hard evidence that says chip X will NOT work with the Ultimate, but if you have a stocker in there you know that if there's a problem, that's one less thing to worry about.

I say try it. If the truck performs up to par, run with it. Otherwise, find a stocker or have someone reprogram that ATR with a stock bin.

Michael
 

smeagol

Active member
The eprom itself doesn't matter. I have a memcal or two without an eprom that was used for piggybacking an Ultimate.

What matters is the circuitry on the other side, for the ESC filtering & backup fueling. ESC stuff is the big importance. Important that the memcal used is from a Syty application.
 
Top