Ultimate or???

Don W.

Stab it and steer it
So I buy a chip advertised as an Ultimate (not a 10 in 1). I wait to install it because I want to install my gauges first. I now have the gauges in. (All are in, only boost is connected at this time, which I think is the most important. Fuel pressure will be next as soon as I have the adapter.) So I install this chip and the thing runs like crap. It’s like I’m in valet mode all the time. Rev limiter is around 4000 and I’m getting boost spikes (at least one that I saw) to 20-21 lbs. Not only that it’s missing, has part throttle dead spots, you name it just about. This chip has a “selector” that clicks from 0 through 9. I gave up at 4, no apparent change in any setting. Did not run a Datamaster, to upset at the moment.


chip1.jpg



I pull the chip and go back to stock and I have my old motor back. Runs good but I see that I’m making only 10, maybe 12 lbs boost now that I have a real boost gauge. I’ve inspected the wire to the “selector” and found no apparent damage, which might lead to the valet mode issue.



What gives, comments, ect.

Thanks,


 

SY2932

Administrator
Re: Ultimate or???

Did you follow the instructions to a "T"? I can't even tell you how many owners botch up this step and blame it on the chip :roll:... I can PERSONALLY assure you that EVERY chip is QC checked before it is shipped out. If you still have a legimate problem, shoot an email to Todd A.
 

Don W.

Stab it and steer it
Re: Ultimate or???

Mike,

I understand. Please do not be offended; I did NOT purchase this chip from Sytychips.com. It was purchased form a seller on syty.net just as you see it. No directions, no nothing. Directions I got from the site and followed them exactly. That’s not to say I didn’t do something wrong. It’s just that those are the results I got.

One of the things I’m attempting to do is confirm that I, in fact, have an Ultimate chip.

Also if I could somehow find some operating instructions it would help. What I have now is a hand written note from the seller with 5 settings. 0,1,2,3,4. 0=valet, through 4=21lbs boost with race gas.

Come to think of it “4” was where I hit the 21lb boost spike before it quit running. Like I said it does not run well at all and is rev limited to 4000 regardless of the setting. I’ll take the heat if I did something wrong but I’m pretty sure I had the chip in correctly.

I'll email Todd.

Thanks much,

Don
 
Last edited:

TYHOGG

Active member
Re: Ultimate or???

I don't know man, your pic looks way different than my Ultimate. My circuit board is tan in color, it has a 6 pin connector than the loom goes to the gauge and the black chip has a "sgt" sticker on it.

I'll try and get some pics up.
 

SY2932

Administrator
Re: Ultimate or???

Yeah, you see those two resistors under the cable on the carrier? That is prolly an older chip, made before I even had a truck possibly...
 

BillC

New member
Re: Ultimate or???

Well, first off, that is most definitely NOT an Ultimate Chip. All UCs have an electronic control box with a read-out showing which program is selected (there have been different size and style control boxes over the years, but the ALL have a read-out).

It looks like an older 8-in-1 or 10-in-1 chip. It may have been burned with later bins pulled from a UC, but that wouldn't make it a UC. I would recommend contacting the seller and getting some money back (the x-in-1 hardware is about half the cost of a UC).

Another thing to check is, is that the correct EPROM for that chip? I don't remember ever seeing an x-in-1 or UC that had a non-matching socket -- the socket should have the same number of holes as the EPROM has pins.

Also, the EPROM should have a sticker over the window. EPROMs are erased by UV light, which is why they have that quartz window over the memory. If you (or someone else) has carried that around outside with the window exposed, the programs are probably trashed.

Finally, did you remember to piggyback the stock chip on the carrier board? Both the x-in-1 chips and the UCs require the stock memcal be piggybacked, so that the knock filtering circuitry on the memcal can be used. If you don't have it piggybacked, the truck will run horribly, like it was in limp-home mode.
 
Last edited:

93ty475

Donating Member
Re: Ultimate or???

what BillC said ^^^^^^^^^

In addition to what he said, datamaster will confirm if the switcher is successfully switching between bins...Just run datamaster and check the top right of the DM screen (PROM ID)...Also, if those are 3bar bins and you don't have a 3bar map sensor installed, the truck will run like crap if you can even get it started....Can't see from the pic, but If for some reason that ancient adapter doesn't have the chip orientation notch, you might have it flipped, possibly causing limp home mode (crappy running)....I sure hope you didn't pay "ultimate" money for that....Is it even digital? or is it some kind of mechanical switcher? interesting....
 

Don W.

Stab it and steer it
Re: Ultimate or???

GreenTyGuy, SY2932, and BillC, 93Ty475

This is great, although unwelcome
icon_frown.gif
, info. I’m gonna contact the seller and see what gives. Everything you guys have said just confirms what I’ve been thinking. I had not realized about the UV light thing. Yes I’ve had it outside. Maybe not in direct sunlight but certainly in daylight.


And yes, I had the stock chip piggybacked.

Yes, it's a mechaincal sw. I was running on my stock 2bar but I have a 3 bar.

But based on what everyone is saying I don't have a UC anyhow. Now that I have this info I might reinstall with the 3bar and run a datamaster .

Meantime I guess I’m back to looking for a real UC.

Anyone?

Really appreciate the info.
Ok.gif


Don
 

93ty475

Donating Member
Re: Ultimate or???

Don W. said:
I was running on my stock 2bar but I have a 3 bar.


bingo...I'm pretty sure all ultimates are 3bar...if so, that will make a huge difference in the way it idle/runs...
 

Don W.

Stab it and steer it
Re: Ultimate or???

93ty475 said:
bingo...I'm pretty sure all ultimates are 3bar...if so, that will make a huge difference in the way it idle/runs...

OK, I can reinstall both the chip and the 3bar. On further research it seems that I purchased an (old?) 4 in 1 chip. If I have to eat it I will.

Assuming (big assumption) the thing works with the 3bar, have I damaged it by exposing it to light?

So even if this works I still think I’m better off with this one on the shelf and a current UC in the truck.
2cents.gif


Agreed??

Don


 

BillC

New member
Re: Ultimate or???

Exposure to sunlight won't damage the hardware, but it might erase some of the bits out of the EPROM. In that case, you would need to get new bins burned to your chip. To prevent it from getting any worse, you should put a piece of masking tape over the window.

The x-in-1 and UC work in a nearly-identical manner: they put multiple bins on the same EPROM, and switch the address from which ECM reads the program and tables. The UC just gives you some extra bells & whistles. If you're only going to switch among just a few programs, the x-in-1 should work just fine.

Please remember, the determination of whether a chip is 2-bar or 3-bar has nothing to do with the hardware, it is determined solely by the code in the bin. So, for example, you could even have 2-bar and 3-bar bins on the same chip (it would be really screwy, but you could do it).

You should probably contact Todd Austinson, to figure out what's going on with that setup.
 

Don W.

Stab it and steer it
Re: Ultimate or???

OK. Put the chip back in and installed the 3bar. Darn thing runs. I’ll post a Datamaster but FWIW it was set for 2bar so don’t know if data is accurate or not. These are not track runs, just launches on a road nearby up to about 90. Got a ways to go here but at least it runs now.

BTW How -do- I contact Todd?
stupid.gif


Thanks everyone


http://www.sonic.net/~donpris/test3.uni



 

HotRudyRod

New member
Re: Ultimate or???

I also had a problem like that when installin my Ultimate, i forgot to rehook the vacuum line to the 3 bar sensor and it gave me the same exact signs as you have now.
It just took a lil recheck and it all turned out great, im very happy with my Ultimate now. May be all you need is a 3 bar sensor.
 

93ty475

Donating Member
Re: Ultimate or???

Don W. said:
OK. Put the chip back in and installed the 3bar. Darn thing runs. I’ll post a Datamaster but FWIW it was set for 2bar so don’t know if data is accurate or not. These are not track runs, just launches on a road nearby up to about 90. Got a ways to go here but at least it runs now.

BTW How -do- I contact Todd?
stupid.gif


Thanks everyone


http://www.sonic.net/~donpris/test3.uni





Don,

If I read the datamaster file correctly, you're getting alot of spark retard under high load....your knock sensor is detecting knock.....I would take it easy and limit yourself to base boost (~10 psi would be good) until you find the source/cause to prevent any premature motor failure.... a pre-ultimate DM file would be nice if you could email it to me or post it for others to view......also a 3 bar, base boost DM file would help as well...
 

Don W.

Stab it and steer it
Re: Ultimate or???

93ty475 said:
Don,

If I read the datamaster file correctly, you're getting alot of spark retard under high load.....also a 3 bar, base boost DM file would help as well...

OK all, I’ve heard from Tom and that chip is commin’ out. It's a very old 4in1.

I have a line on a couple of real UC’s so the story ain’t over but it’s on hold for now.

Regarding the spark retard; I know it’s there just don’t know why. Tomorrow I gonna check spark advance. Been putting it off and can’t anymore.

Then I’m gong racing, Wed night drags at Sears Point so I’ll get some fun out of this “learning experience”. Will try to get some Datamaster runs in as well.

Many thanks Tom and all who contributed to this thread.
2_thumbs_up_-_animated.gif


Don
 
Last edited:

mrweelr

New member
Re: Ultimate or???

Do yourself a favor and mix in 5 gallons of Touline or Xylene with your 91. These trucks runs like shit on monkey piss CA gas. Let us know how you do at the track!
 
Top