yet another failed emissions thread

sy#2921

BAMF
Here is the deal took the truck for the first test failed the HC 470ppm allowed 220ppm. CO was .4% allowed 1.2% but isnt counted against me
Proceeded to change the following:
cap and rotor (msd)
coil (msd blaster)
ignition module
plugs (for emissions only but cr43ts)
o2 sensor (delco)
checked wires and all tested at ~60 ohms
checked timing and was set to zero
fuel pressure set at 46psi without vacuum connected
put a 195 stat in it instead of 160
fuel filter
put one bottle of heet in the tank to like 8 gallons
retested it off the record and failed again 350ppm CO is now down to .1%
my thoughts were that i could do the easy trick of lowering the FP with the AFPR but i want to see if i cant correct whats going on.
Any suggestions???
quick storm wanna chime in?
 
Last edited:

jwaller

Evil Genius/SyTy Guru
Re: yet another failed emissions thread

you didnt change the oil that I can see and you didnt turn off your IC pump. those are two more suggestions. also I hear using 87 oct for the test will help. 46 psi seems a bit high but I dont know your build either.
 

sy#2921

BAMF
Re: yet another failed emissions thread

guess i did forget some good info like my build
dequick a2a
60 series turbo
50#
3" exhuast
dual electric fans
conservative tune from dig
those are all the relevent performance mods.
CO2 on the first test was 12.7% and now it was at 14.3%
one problem i know i am having still is the truck runs too cold with the electric fans because with the 160 stat it runs at 130-135 and then with the 195 stat it was running at 160
i was suggested to put an msd box on the truck just for the test since it is an idle test only and it would help burn the extra fuel that i guess i am not right now. I have a spare 6a box laying around i was going to try
 

sy#2921

BAMF
Re: yet another failed emissions thread

first test was on a set of UR6's that were 4+ years old gapped at about .035 and the retest had a set of delco cr43ts gapped at .035 since i figured a hotter plug would help and i wouldnt be driving hard so it wouldnt be prone to detonation. I do have a brand new set of UR6's at home i could put in if needed
 

jimhrabe

Donating Member
Re: yet another failed emissions thread

Join the club mine is mostly stock and I'm having probs with emissions gotta check my timing though
 

sy#2921

BAMF
Re: yet another failed emissions thread

yeah i remember talking to you about it at the gtg and now i am in the club. It sucks i just found out that IL is more strict than NV and CA for some reason. cause my truck passed NV emission earlier this year when mike still owned it but he doesnt know any of the details of the testing. scrapn' Ive got a timing light we can check your truck with if you want to setup a time to do so
 

TYTILIDIE

METH HEAD
Re: yet another failed emissions thread

What wires are you running? How does the truck run overall? CEL? If you are running anythign other than S10 wires, make sure you ahve straight boots on # 1 & 6. My MSD's were all 90* boots and this killed me. HC's were through the roof. HC's are unburned fuel.
 

sy#2921

BAMF
Re: yet another failed emissions thread

im running the 10.4mm taylor "409" spiro pro wires. truck runs great and even better now with the tune up. No cel and havent seen once other than when i was setting the timing. All plugs have 90* bends due to the atr headers and clearance issues with those and the 3" dp. I have found out that HC is unburnt fuel but there is no reason my truck should have such a high count. i will try the msd box with lowering the fp and see what happens i guess
 

sy#2921

BAMF
Re: yet another failed emissions thread

went for another voucher today. put an msd 6a box on the truck and dropped the fp from 46 to 36
HC's went from 365 to 335 still no where near 220 boo!!
any more ideas?
 

SeattleSy#1255

Category 5 Conservative
Re: yet another failed emissions thread

i thought you could drop FP and go in there with the tan wire unplugged and pass...i can't remember where I read that, but that is what I though.
 

sy#2921

BAMF
Re: yet another failed emissions thread

hmmm thats a good idea. only problem i see is the check engine light comes on and i think they would fail me for that guess i will have to ask about that
 

JuStBlAzIN

Active member
Re: yet another failed emissions thread

damn they let you pass the visual with all those mods? headers, 3" exhaust... damn.. here in cali i would fail befor my truck even got on the machin, do to all those visual mods.
 

sy#2921

BAMF
Re: yet another failed emissions thread

the only mod they actuallyknow i have is a 3" tailpipe. The people who work there are so simple when it comes to cars that they for one dont know that a syclone is something special and two the inspection here in IL is not very intensive. All they do is a mirror check for a cat then they will only do a complete visual inspection and check for all emissions stuff after you fail the 4th time. They dont care if the vehicle is modded as long as it passes the standard. They know the truck has all the stuff done since i was talking to them about why it wont pass.
 

Beavis

Still plays with trucks
Re: yet another failed emissions thread

Cat Converter... new or old? that may help...read that somewhere:dunno:
 

sy#2921

BAMF
Re: yet another failed emissions thread

cat is old but i just checked it out visually its full not clogged and i can see through it and also a pyro gauge reads an 80 temp difference from inlet to outlet so its working fine
 
Top