Search results

  1. dgoodhue

    Burning a chip in flash and burn, tunerpro

    Re: Burning a chip in flash and burn, tunerpro I have not used chip burn and flash or burn 2, but the concepts are th same for most chip burners and bin readers/programmers. I am guessing you are missing the chip offset. The chip (512k bits) you have is bigger than the programs that your are...
  2. dgoodhue

    Timing question.

    Re: Timing question. Are you using a piston stop to find TDC? If so, you need to spin motor both ways to find TDC.
  3. dgoodhue

    Largest Front Anti Sway Bar?

    Re: Largest Front Anti Sway Bar? The weight distribution and archaic suspension leads understeer as well as having no factory sway bar. A rear sway bar will help with understeer. A larger front sway bar make the truck handle flatter, but it transfer weight to the rear. In the case of our...
  4. dgoodhue

    Best adhesive for cladding?

    Re: Best adhesive for cladding? I wouldn't want to use an adhesive tape that is strong as rivets. If you ever needed to disassembled it, you likely would have break the cladding (most cladding these days is brittle to begin with)
  5. dgoodhue

    Best adhesive for cladding?

    Re: Best adhesive for cladding? The bottom of the front fender cladding should be bolted, before and after the wheel openings. Their is supposed to double sided tape on the vertical section just in front of the door.
  6. dgoodhue

    BW4472 rebuild

    Re: BW4472 rebuild At least a few of his 4L80E transmission builds didn't have the upgraded internals parts that the buyer paid for.
  7. dgoodhue

    '96 4.3 vortec build

    Re: '96 4.3 vortec build I didn't build the heads but it has Ferrea valves. Looking at Ferrea website, I suspect it's part number F6161.
  8. dgoodhue

    Typhoon at BJ Auction

    Re: Typhoon at BJ Auction There is more stuff missing/different the list was getting too long to continue.
  9. dgoodhue

    92 vs 93 shift lever button?

    Re: 92 vs 93 shift lever button? My old 93 Typhoon looked like the same shifter button as my Syclone which looked the same as my 86 Corvette. I had all 3 shifters apart.
  10. dgoodhue

    Typhoon at BJ Auction

    Re: Typhoon at BJ Auction The engine compartment has a whole bunch of little minor issues with it. Someone overly glossed it up which I don't care for. AC deleted, Heater hose isn't correct, wrong routing, missing the IC metal, aftermarket coil mounted on the firewall, splotching intake...
  11. dgoodhue

    '96 4.3 vortec build

    Re: '96 4.3 vortec build Looking through my old pictures, it looks the reluctor ring is recessed a little.
  12. dgoodhue

    '96 4.3 vortec build

    Re: '96 4.3 vortec build I know what your saying but GM spaced the crank so the timing gear, reluctor ring, balancer and crank pulley align properly so the serpentine belt alignment didn't change for either motor. I do have 03 vortec motor in my Syclone that stripped down to the short block...
  13. dgoodhue

    '96 4.3 vortec build

    Re: '96 4.3 vortec build I don't believe the balancer is any different for the balance shaft motors than non balance shaft motors. It's mounted outside of the timing cover, so its not affect by the spacing of the balance shaft gears / reluctor ring.
  14. dgoodhue

    My Sy 4-$@le Texas

    Re: My Sy 4-$@le Texas The puff of smoke on start up is likely a coincidence that it started happening when you changed chips. It is almost always the valve seals. It is common issue as these truck age. Trucks that sits for periods of time are more suspectible to them drying out and causing...
  15. dgoodhue

    IAC torment

    Re: IAC torment It sound like someone adjust the throttle stop on throttle body to me. The IAC passages couple also be clogged up preventing the IAC from fully closing as well.
  16. dgoodhue

    Owned this truck for a few years and just noticed...

    Re: Owned this truck for a few years and just noticed... You also wouldn't use your high beams when their was fog.
  17. dgoodhue

    '96 4.3 vortec build

    Re: '96 4.3 vortec build You need to use a balance shaft timing chain set because of how the balance shaft spaces the cam gear. I don't think the traditional SBC timing gear set can be used. I used GM parts. GM had a TSB for timing chain for rattling, so that is what I used based on another...
  18. dgoodhue

    '96 4.3 vortec build

    Re: '96 4.3 vortec build I have a junkyard balance shaft short block in my truck, so its a 2 bolt motor. It was my 1st blank sheet tuning project I had done, so I didn't want to risk damage a built short block. Some day I will build another motor. The junkyard motor has lasted longer than I...
  19. dgoodhue

    '96 4.3 vortec build

    Re: '96 4.3 vortec build I had done a lot research and calculations as well, but I did all that over 10 years ago, so it isn't all fresh in my mind. Some parts have probably changed since I was last buying/build my engine. I used ARP 233-3701 12 point cylinder head bolts. My engine is up...
  20. dgoodhue

    Classic car insurance options?

    Re: Classic car insurance options? I have American Collectors Insurance, but that was all that was available in MA up until last year. I fortunately haven't had to use it. I have an agreed value policy and I am limited to 3,000 miles year. I think it needs to be garaged as well, but I am not...
Top