Search results

  1. dgoodhue

    Running a little rough

    Re: Running a little rough 46psi when idling is a lot. Is that with the vacuum connected? What do you have for a chip?
  2. dgoodhue

    Build engine shift points

    Re: Build engine shift points IIRC Don is using the Turbotweak. It probably happens under ECM control and it would need modified in the programming. My code $59 default is to automatically locks at a certain mph which happens to be 3rd gear.
  3. dgoodhue

    ty is dead need help!

    Re: ty is dead need help! It is too bad that the former owner didn't just buy the $15 harness so the MSD could plugged in or bypassed in this case. The ignition module sometime goes in these truck which causes a sudden no spark condition if it fails.
  4. dgoodhue

    Getting Syclone #845 Back on the Road

    Re: Getting Syclone #845 Back on the Road The goodwrench motor would have been wrong; The TRW piston in 2002 would bring the compression to the right range for a syty motor.
  5. dgoodhue

    Getting Syclone #845 Back on the Road

    Re: Getting Syclone #845 Back on the Road Oops, i look through my email receipts and I actually stayed in Salida, when I went to Modesto. I did a bunch of travel for that company, so it all kind of blended together.
  6. dgoodhue

    Getting Syclone #845 Back on the Road

    Re: Getting Syclone #845 Back on the Road I have been to CA only once, but it was for a business trip to Modesto. I am pretty sure my hotel was in Sonora. I know there is/was Syclone owner on the highway between Modesto and SF (I want to say it was halfway between), because I was going to...
  7. dgoodhue

    Getting Syclone #845 Back on the Road

    Re: Getting Syclone #845 Back on the Road This where I got my parts. I guess sometimes you need to replace the bearings, but my truck has low miles so I didn't do that. https://cobratransmission.com/index.php?main_page=index&cPath=3_2080
  8. dgoodhue

    Getting Syclone #845 Back on the Road

    Re: Getting Syclone #845 Back on the Road You need to the truck aligned by a shop or alignments. I have some alignment tools. I initially did mine by eye by looking at the rear wheels and body work to get started. I way off when put the camber tools and started measuring. I was surprise how...
  9. dgoodhue

    Getting Syclone #845 Back on the Road

    Re: Getting Syclone #845 Back on the Road No, the auction compatibility is incorrect. The transfer cases are 89-91 and 92-95. Its a 93, you would need to change your driveshaft for it to work. I would not buy a used transfer at this point, they are all approaching 25 years old and IMO are...
  10. dgoodhue

    Lean burn?

    Re: Lean burn? It is pretty likely that your engine is running lean, but you should confirm it with a scan tool datalog. In addition to increasing the airflow with the heads & cam, the higher effective compression with the lower boost level compounds the issue as well for the engine air flow...
  11. dgoodhue

    Tires

    Re: Tires I would probably buy the summer tire version of those tires instead of the All Seasons. I think at this point a good majority don't drive our SyTy year round...
  12. dgoodhue

    internal engine questions

    Re: internal engine questions The high oil pressures can cause problem for some turbo's in particular ball bearing turbos. I would use a standard volume Melling Select. Our engines aren't high reving. I would do a 4 bolt mains unless your planning on only using small turbo and lower boost...
  13. dgoodhue

    Starter problem

    Re: Starter problem You are lucky, take this as a learning lesson. Even if you had used wheel chocks with your jack, I would not have gotten under the car. I ideally I like to use ramps and wheel chocks and if I can not use those, I use a jack stand in secure locations that I know aren't...
  14. dgoodhue

    Ran 11.597

    Re: Ran 11.700 Re: Ran 11.700 Great job as usually. I wish I had as much fun racing my truck as you do.
  15. dgoodhue

    Stock Brakes Suck. My Idea for an Inexpensive Upgrade.

    Re: Stock Brakes Suck. My Idea for an Inexpensive Upgrade. I think the stock brakes suck as well, obviously that is just my opinion. I think a stock truck accelerates too quickly for the braking distances. Upgrading my brakes was one of the best mods I had done to my truck and I am positive...
  16. dgoodhue

    Trans issue

    Re: Trans issue I think I used a wratcheting strip with a small socket in the middle of the cover for a little clearance to compress the servo cover. (I may have used the strap with the transmission out.) I know that I removed the servo with the trans installed in my Syclone. I didn't want...
  17. dgoodhue

    Dipping idle

    Re: Dipping idle Do you have any mods? 800rpm idle is high is the engine mostly stock. I would inpsect/replace your vacuum lines.
  18. dgoodhue

    what should i improve on?

    Re: what should i improve on? You can improve on your 60' time, but that might be dependent on the age of your tires. Your 1/4 mile time is pretty good already for a Typhoon. You could datalog your ECM to see if their are additional improvements, but with your timeslip I bet it looks pretty good.
  19. dgoodhue

    Going to look at syclone with 60k mikes..tips?

    Re: Going to look at syclone with 60k mikes..tips? Maybe he really can't tell us more....
  20. dgoodhue

    Heater core

    Re: Heater core I bought a copper heater core from Sportmachines.
Top