Search results

  1. George Blake

    Upgrading to LS1 brakes soon, need some info.

    Re: Upgrading to LS1 brakes soon, need some info. Won't work. They physically bolt together but it will hang over the rotor about 1/4". I tried it to because someone heard it from someone that heard it from someone else that it would work. Yep, bolts together, but doesn't work. I posted up a...
  2. George Blake

    4l80E +what year

    Re: 4l80E +what year It's ok if its a 2wd. It will have the reluctor ring on the planetary so you can plug it in for TOSS signal easier. You'll either have to change the output shaft for the cut down 27 spline or swap the current output shaft for a 4 wheel drive version. If it's a long spline...
  3. George Blake

    4l80E +what year

    Re: 4l80E +what year If you can get the 4wd, you can do the upgraded input shaft for the transfer case. If you want to do the cut down shaft, I have some of those left as well but the 32 spline setup is what just about everyone does now.
  4. George Blake

    4l80E +what year

    Re: 4l80E +what year How much newer is the newer one? If its a 1999, then go with it. If not, just update your old one. The updates will cost less than the $400 difference.
  5. George Blake

    4l80E +what year

    Re: 4l80E +what year 1993 is fine. Your gonna update: All the pistons to bonded steel except for the 2nd piston. New A and B shift solenoids New TCC PWM solenoid New PCS solenoid (you mod the valvebody when you do this, ask how when you do it). Update the AFL. Actuator Feed Limit valve. Either...
  6. George Blake

    240sx +lsx+ syty?

    Re: 240sx +lsx+ syty? To go from house to shop to get the propshaft measured and fixed, OK. Driving around daily back and forth to work. No. You'll damage the viscous.
  7. George Blake

    5 pinion billet planetary for the 4472

    Re: 5 pinion billet planetary for the 4472 OK. There was a hangup at heat treat. Being a thin wall tube (sun gear shaft), they had to figure out the best way to set it up during heat treat so it didn't deform. They got it figured out, had to be hung in a special fixture during heat treat. They...
  8. George Blake

    RPM's erratic over 2800-3000rpm?

    Re: RPM's erratic over 2800-3000rpm? What I've found is that it's best to ohm out all your wires before installing them. I've found multiple bad wires. Usually the resistance will be really really high on one or two wires. Also guys will ask what kind of plugs you used. CR42TS is recommended...
  9. George Blake

    RPM's erratic over 2800-3000rpm?

    Re: RPM's erratic over 2800-3000rpm? Ignition. One of the wires may not be seated correctly.
  10. George Blake

    LS1 TT typhoon build(fabrication 95% complete)

    Re: LS1 TT typhoon build(updated pics) Re: LS1 TT typhoon build(updated pics) I don't think anyone is bashing you. You do LSX style swaps all the time. Your used to having to redo everything cut frames, etc. What we were trying to point out is that others have already done them in the syty, so...
  11. George Blake

    LS1 TT typhoon build(fabrication 95% complete)

    Re: LS1 TT typhoon build(updated pics) Re: LS1 TT typhoon build(updated pics) From what I can gather, he's trying to do his own thing. His shop does LS1 conversions all the time..... There will be a learning curve. Heaven forbid he's listen to a bunch of syty amateurs :rotf: Kinda like the...
  12. George Blake

    LS1 TT typhoon build(fabrication 95% complete)

    Re: LS1 TT typhoon build Re: LS1 TT typhoon build Check your current planetary good. I've got 4 torn down now waiting on planetaries and all but 1 had the pinions wiggling around in them where they'd failed. If anything replace it with a new stock style. That was a shame having to cut the...
  13. George Blake

    Starting T-56 Conversion

    Re: Starting T-56 Conversion Adam went 80e full billet with Shrifter setup. I think he's swapping from TCI TCU to the Big Stuff 3 module. There are some vids of him beating on it on a road race course. Very cool.
  14. George Blake

    My budget LQ4/4L80E build! update, way over budget, 9's or bust!

    Re: My budget LQ4/4L80E build! Re: My budget LQ4/4L80E build! It'll make it a lot easier if you get rid of the big crossmember and do one yourself. If you can make the transmission crossmember, you can make the frame stiffener back there.
  15. George Blake

    80e Install Pics - Need Help

    Re: 80e Install Pics - Need Help That should've been a magazine writeup. That is an incredibly clean truck. I was just looking at it again and can't believe it. It looks like new underneath.
  16. George Blake

    5 pinion billet planetary for the 4472

    Re: 5 pinion billet planetary for the 4472 Went up and gave the monies to Kevin today and everything is on schedule. The sun gears are done with the first cut and off to heat treat as of yesterday. Should be back friday for final fitment of each piece, get the bushings pressed in the sun gears...
  17. George Blake

    why not go with A turbo 400 or powerglide?

    Re: why not go with A turbo 400 or powerglide? It most likely isn't an issue "completely" of torque handling ability. Custom gear ratios, special pistons, special sprags, the stuff adds up quickly. And to go with the first question, it's just gonna depend on what the use of the vehicle is...
  18. George Blake

    My budget LQ4/4L80E build! update, way over budget, 9's or bust!

    Re: My budget LQ4/4L80E build! Re: My budget LQ4/4L80E build! Manual shift shaft is too long. It won't clear the prop shaft. See it stick WAY out of the trans? You need the sonnax short manual shaft. Probably would've been best to have installed that during the shift kit install. The pin that...
  19. George Blake

    80e Install Pics - Need Help

    Re: 80e Install Pics - Need Help Watch what Jeggs and Summit does, that price doesn't include the 80e/60e harness. That's another $170 or so. Also comparing the TCI "price" to the PCS "price" is not clean either. PCS price doesn't include USB to serial converter, harness or converter software...
  20. George Blake

    80e Install Pics - Need Help

    Re: 80e Install Pics - Need Help Yours wouldn't fit like their's because it's a newer design with the mounting pads integrated into the housing.
Top