Search results

  1. George Blake

    80e Install Pics - Need Help

    Re: 80e Install Pics - Need Help You put the extension plate that goes on the transfer case on upside down. If you flip it over, you'll see it puts everything in the position that your spacers ended up doing. If it works, leave it in there but if you want the spacers out, flip the bracket over...
  2. George Blake

    80e Install Pics - Need Help

    Re: 80e Install Pics - Need Help If the manual shift shaft in the kit was too long then they didn't give you the one they originally had. The shift shaft is a Sonnax part the shortest available and must be installed at the time of build, so Chris would've had to have installed it at his shop...
  3. George Blake

    My budget LQ4/4L80E build! update, way over budget, 9's or bust!

    Re: My budget LQ4/4L80E build! Re: My budget LQ4/4L80E build! In this picture It looks like your front case bushing is sitting on the input shaft. If it is, that shouldn't be loose enough to fit like that. If it was just laying there for mockup, ignore me. If it just kinda fell out of the...
  4. George Blake

    5 pinion billet planetary for the 4472

    Re: 5 pinion billet planetary for the 4472 Brandon Eldred (Paid In Full for everything) X2 setups Robert Stevenson (Paid In Full for everything) Keith Watson (Paid in Full for everything) David Enama (Paid in Full for everything) Jamie Hacking (Paid in Full for everything) David Saunders (Paid...
  5. George Blake

    Who has personally rebuilt a 4l80e

    Re: Who has personally rebuilt a 4l80e It's not too awful bad. You have to actually be a little better than a 700 because there are a LOT more components to inspect. Valvebody has several MORE areas to inspect and correct and all the bushings will need replaced and many need resized in place...
  6. George Blake

    My budget LQ4/4L80E build! update, way over budget, 9's or bust!

    Re: My budget LQ4/4L80E build! Re: My budget LQ4/4L80E build! I'm gonna put up some additional instructions for that kit. You can ONLY do them as a KIT. I don't want others thinking they can do them when the link goes up.
  7. George Blake

    Running a Ty T-case in 2wd?

    Re: Running a Ty T-case in 2wd? Yours may have not instantly died but you did do damage to the viscous fluid and decreased the life of the clutch. You don't have to drive it hard to finish one off. If you read that thread at the end, it will be obvious how it works and how it does damage the...
  8. George Blake

    Running a Ty T-case in 2wd?

    Re: Running a Ty T-case in 2wd? Go to my Bw4472 billet planetary thread. There is a full explanation of how the transfer case works. You'll burn the viscous up. Your tricking the viscous into thinking the front is always slipping so it will attempt to lock the front in more (through heating of...
  9. George Blake

    LS1-Sonoma GT build (updated with pics)

    Re: LS1-Sonoma GT build (updated with pics) You don't have to get it from me. Get a junk yard 2wd 4L80e, put new gaskets and seal and filter kit, 34 element sprag, bonded steel pistons. New clutches, TransgoHD2 kit, new bearings and thrust washers, ohm out the electronics, probably need a new...
  10. George Blake

    Replace or rebuild tranny?

    Re: Replace or rebuild tranny? At 20% throttle, it should shift to 2nd between 11 and 16 mph.
  11. George Blake

    LS1-Sonoma GT build (updated with pics)

    Re: LS1-Sonoma GT build (updated with pics) The thinner clutches have notoriously failed in higher HP 700r4 apps. That why most go with Raybestos gen 2 blues and put 7 clutches with thicker steels. You've got to keep the heat pulled off that clutch material. The 700r4/60e has it's unique dual...
  12. George Blake

    LS1-Sonoma GT build (updated with pics)

    Re: LS1-Sonoma GT build (updated with pics) Here's the reinforcement kit: http://www.sonnax.com/instructions/77733-01K-IN.pdf Get the one that comes with the aluminum piston already done. The instructions say that you cannot use a bonded steel forward piston with this setup. That is not true...
  13. George Blake

    LS1-Sonoma GT build (updated with pics)

    Re: LS1-Sonoma GT build (updated with pics) Better than stock yes. 675 HP. No. You will still tear up the overrun hub. Input drum should be reinforced and cryo'd. Sonnax sells the kit now. Before you use the kit, air check the input drum and make sure it doesn't leak air between the input...
  14. George Blake

    LS1 TT typhoon build(fabrication 95% complete)

    Re: LS1 TT typhoon build Re: LS1 TT typhoon build I tried to talk him into the the one off transfer case planetaries I'm doing to compliment the input shaft he got but he wouldn't bite. Maybe he'll change his mind later. That's gonna be a very clean build.:tup:
  15. George Blake

    5 pinion billet planetary for the 4472

    Re: 5 pinion billet planetary for the 4472 It was really nice talking to you! You have a great Thanksgiving! Also updated list.
  16. George Blake

    Transfer case may be busted

    Re: Transfer case may be busted Check the planetary and the output shaft. There should be a scoop on the output shaft that feeds an orifice in the center. It will probably be gunked up from planetary debris. Use carb cleaner and compressed air to clean the needle bearings in the output shaft...
  17. George Blake

    Wow

    Re: Wow Why did you donate? You said yourself you could do this exact same thing for $300 a year. Is it the forum's fault you had a bad experience with a vendor? No one backed you in a corner. Your still promoting some sense of impropriety. Your wanted to know how much. So if a server fails and...
  18. George Blake

    well.. i blew the tranny again

    Re: well.. i blew the tranny again Ok. It's killing me. First you ADMITTED to racing 40 times(probably more) on the weekend every weekend AT THE TRACK. Then you said you were doing highway racing with motorcylces at MAX speed for LONG durations of time. How much are you actually making street...
  19. George Blake

    well.. i blew the tranny again

    Re: well.. i blew the tranny again This stuff is all over the internet but I'll post it here. Thin clutches for the 700r4 3-4 clutch pack. BAD. That is a DYNAMIC clutch. Remember? Constanty cycling back and forth EVERY upshift and down shift. This creates lots of HEAT. The THIN clutches and...
  20. George Blake

    well.. i blew the tranny again

    Re: well.. i blew the tranny again Go with the 2007. It's free. You can always REUSE the controller if you go 80e. And you'll get back on the road quicker. Do some measuring and see how close it would be. Ask Rodger (sparkwire) and see what all he's got. Especially if the freebie has a...
Top