Chip Question

I would like to know if you can get a chip that is 3 bar, and doesnt have all the programs like the ultimate? I dont care to have the valet or the t3 settings. I would like to have one that is set to 20 psi. Can it be done? If so how much?
 
I have looked at them . But I dont have and cant afford wb o2, or the chip burner . which is two of the things they say you have to have. Also I dont have bigger injectors.
 

kwick6

Donating Member
Only luck your going to have is getting a bin from someone else that may or may not work well for your combination. I have a TE44 on my truck as well, and there are some areas of the calibration that could be smoothed out... so I don't think you'd be too happy with a bin thats from someone elses truck, or at least not for long.

here is a good quote from Dig...
Boil down the question, and it comes to:
"How good is good enough".

If 75% of your max potential performance is
good enough, then a one-size-fits-all chip
will be enough for you.

If nothing less than the fastest you can go
will do, you're never gonna be happy with
anything but a full-custom tune.
(IE, with a Wide-band)

IMO, start thinking about the WB setup (its really not all that expensive, except for the sensor ~$180) and a burner is about ~$150.

I have those things now, and after I get some good practice with em, I'll probably tryout the romulator. 8)
 

Buster

New member
kwick6 said:
Only luck your going to have is getting a bin from someone else that may or may not work well for your combination. I have a TE44 on my truck as well, and there are some areas of the calibration that could be smoothed out... so I don't think you'd be too happy with a bin thats from someone elses truck, or at least not for long.

here is a good quote from Dig...
Boil down the question, and it comes to:
"How good is good enough".

If 75% of your max potential performance is
good enough, then a one-size-fits-all chip
will be enough for you.

If nothing less than the fastest you can go
will do, you're never gonna be happy with
anything but a full-custom tune.
(IE, with a Wide-band)

IMO, start thinking about the WB setup (its really not all that expensive, except for the sensor ~$180) and a burner is about ~$150.

I have those things now, and after I get some good practice with em, I'll probably tryout the romulator. 8)

The romulator will teach you. Seriously, a few day with the romulator and you'll know how to tune, a few years with a chip burner and you'll know how to tune.
 

kwick6

Donating Member
Buster said:
kwick6 said:
Only luck your going to have is getting a bin from someone else that may or may not work well for your combination. I have a TE44 on my truck as well, and there are some areas of the calibration that could be smoothed out... so I don't think you'd be too happy with a bin thats from someone elses truck, or at least not for long.

here is a good quote from Dig...
Boil down the question, and it comes to:
"How good is good enough".

If 75% of your max potential performance is
good enough, then a one-size-fits-all chip
will be enough for you.

If nothing less than the fastest you can go
will do, you're never gonna be happy with
anything but a full-custom tune.
(IE, with a Wide-band)

IMO, start thinking about the WB setup (its really not all that expensive, except for the sensor ~$180) and a burner is about ~$150.

I have those things now, and after I get some good practice with em, I'll probably tryout the romulator. 8)

The romulator will teach you. Seriously, a few day with the romulator and you'll know how to tune, a few years with a chip burner and you'll know how to tune.


:rofl: , ya I'm sure its much faster to work with.

whats another $179.95, for something that cool.

I should probably just sell the PP2 I have for $150 and get the romulator.
 
Boil down the question, and it comes to:
"How good is good enough".

If 75% of your max potential performance is
good enough, then a one-size-fits-all chip
will be enough for you.

If nothing less than the fastest you can go
will do, you're never gonna be happy with
anything but a full-custom tune.
(IE, with a Wide-band)


75% of max potential would be alot better than 50%. Also I drive my truck everyday so running right on the edge is not that good of an idea for me.
Plus I am not good with computers. :( I could probley look hard at an ecm and make it crash :lol: The pocket romulator sounds cool but I would screw somthing up quick.

I would just like to be faster than I am now. Last time to the track I went 8.18@86 1/8 mile on 13-14 psi
 

turbodig

Active member
Buster said:
[


The romulator will teach you. Seriously, a few day with the romulator and you'll know how to tune, a few years with a chip burner and you'll know how to tune.

This is probably one of the single most dangerous ideas I've seen on
this board.

The RTEditor/Romulator setup is very easy to use, and learn.... which
makes it extremely dangerous in the hands of a novice tuner.

The wrong bump of a mouse can blow a motor up.

Taking the time to roll into tuning slowly, changing values by small
amounts, and knowing what it is that you're changing takes time to learn.

While it's a relatively simple matter to tune the VE tables to get a flat
AFR, it takes some time to understand how the tables interact with each
other, and to understand the true relationship between timing, boost,
and AFR. It's taken me years to figure certain things out, and there are
still things that I don't understand well enough to predict what changing
a particular value will do.

You can get a long way on "By-guess-and-by-golly", but it will cost you
some broken parts somewhere along the way.

This is not unique to Romulator. Any interface that allows you to change
engine parameters "on-the-fly" depends on the operator to impart good
judgement into the values that you put into the tables. FAST, Motec, AEM-
this applies to all.

I don't mean this to discourage people from getting into tuning; just take
it slow, at a pace where you can understand things. And write things down,
so you know what you did, and how much it affected things.

Back to the original post, though-

At a minimum, you need a scan tool that can log files. Your most econ-
omical way of doing this is building your own cable (If you spend more
than $20 building it, you spent too much), and using one of the free
scan tool products. Freescan - http://www.andywhittaker.com/ecu/ecu_software.htm

DataMaster is somewhat the SyTy standard, if you have that already
you're well on your way. You can use it x times for free, so at least
you'll have that many diag passes.

I can tune a chip based on Datamaster/Diacom data only. I don't prefer
that, since you're not getting all the good Data the WB provides, but it
can be done. I'm working on getting a few WBs together for the people
I tune for, on a deposit basis. Not there yet, though.

The big thing, though, is fix the things that are wrong. A healthy Sy with
a stock 2 Bar chip should run at least 13.7 (Alt. corrected). Slower than
that, and something's wrong. This may involve removing mods to get it
back to stock, just for diagnostic purposes.

I ran a 12.6@108 years ago, on a stock turbo with race gas and a 2 Bar
chip with 20-21 degrees of timing.

No chip in the world, however, will fix problems. It will likely only make
things worse, and may result in broken parts. Gotta fix the issues before
you can make power.

later,

Dig
'91 Sy - 11.94@114
Still Original heads, short block, and cam.
 

Buster

New member
This is probably one of the single most dangerous ideas I've seen on
this board.

This was somewhat directed to Scotty, who was like me a year ago. He's read a lot, made some changes, has a basic idea of what's what. I learned all the basics from you and BG, but I really learned what's what when I fired up the romulator and could make changes and watch them happen in real time.

Just to make it clear, I couldn't have done it without your guys help, but the learning curve really took off when I was hands on tuning in RT.
 

kwick6

Donating Member
Only thing I'd feel comfortable making changes in is promgrammer.

I'll start out slow, because I wanna see what changes affect what. I want to know when I made a change , if it was the right one to make. So it will probably take me alot longer to tune my truck even with a wideband, than it would you experienced people, because I'm going to want to know what each change I'm making is gonna do to the overall picture.

I can see that even though it might be faster on the romulator, the way to learn is with a burner, taking note of every change and driving to see if that was the correct change needed.
 

Buster

New member
kwick6 said:
I'll start out slow, because I wanna see what changes affect what. I want to know when I made a change , if it was the right one to make.

I'm not going to push this too much more, but making small changes and watch there effects is exactly what the RT stuffs all about.

Chips are slow and the romulators fast, it doesn't mean you can't make small changes with the romulator, you just don't have to shut the truck down, walk to the house, make a chip, and then start all over. Walking to the house before you make the change ain't going to make it any safer.

Last thing, You'll never know until you make a guess if its right or wrong, the difference between a newbie and experience tuner is the experienced tuner makes better guesses.
 

E-Rue

New member
Walking to the house before you make the change ain't going to make it any safer.

hahaha
herd dat!

i dont mean to disagree with dig, but i dont think anyone should be scared of tuning. yes you can mess up, but if you read and take your time, its something anyone can learn. there have been so many ahead of us that have already fumbled thru the really hard stuff, and have paved the way so that the rest of us can get on a website and start tuning in a matter of days. most everything you need to tune a truck is readily available, and cheap/free for the taking. all you have to do is want to learn. if you get stumped, make a post, the rest of us are more than willing to help.

e
 

turbodig

Active member
Buster said:
kwick6 said:
I'll start out slow, because I wanna see what changes affect what. I want to know when I made a change , if it was the right one to make.

I'm not going to push this too much more, but making small changes and watch there effects is exactly what the RT stuffs all about.

Chips are slow and the romulators fast, it doesn't mean you can't make small changes with the romulator, you just don't have to shut the truck down, walk to the house, make a chip, and then start all over. Walking to the house before you make the change ain't going to make it any safer.

That's a good point, but it does give you that amount of time to think
about the change. This isn't as important for you and the other guys
who have a few dozen hours of tuning under your belt, but it's really
important for those just starting out.

The chip burning cycle was/is a PITA... no doubt about it. It did serve a
purpose, though, in enforcing that a little bit of extra thought was put
into what was being changed. Sort of a "Are you really sure you want to
do this?" kinda thing. Annoying for the advanced, sure, but good for the
novice.

There were a great many times when my planned change changed
between the house and the garage. Without the burn cycle, it sorta
degrades to shoot first, ask questions later.

In that mode, you're going to make a mistake eventually... everybody
does. As long as the change is small enough, you're probably not going
to hurt anything. But a true novice doesn't know to make small changes;
they might think- "I'm gonna add 8 degrees of timing to this block right
here" and, kaboom.

This is, the inherent danger with the Romulator/RT setup... it allows you
to make fast, instant gratification changes, without the discipline that
comes with time. This is a good thing for the medium to advanced tuner,
a bad thing for the true novice.

Your original post was to Scott, and for him and others like him, what
you said has a grain of truth. However, a great many people see this
UBB, including people who aren't so experienced in tuning operations,
or are even that familiar with basic IC engine concepts. These are the
folks that need to spend some time learning before they jump on with
a tuner.

It took you about 2 years or so to get from no ECM tuning experience,
to where you are now, correct? Basically, all I'm saying is that it *should*
take you that long. RTtuner gives you the power from day 1.


Last thing, You'll never know until you make a guess if its right or wrong, the difference between a newbie and experience tuner is the experienced tuner makes better guesses.

I'm not saying that there's not any guessing involved in tuning- there is.
However, if you watch the trends in the data you change, and their
effects on AFR/MAT/Coolant/Knock, you can predict fairly well what
a change will do- Ie, knowing that 5 VE points will be a certain AFR delta.

When you know your system that well, you're far less likely to make errors.

My .02...

Dig
 
Top