Datamaster Review plz

johnboy89

Member
I was wondering if someone can review my datmaster file.

I'm no expert but looks like low voltage and a lean condtion, seeing some knock!!!!

Other views opinions much appreciated.

There might be some of the old gas still in there which has been sittng for some time(1yr.) before the truck ran last, which might be contributing to the problem.

Thanx:D

http://rapidshare.com/files/422949714/Test_1.uni
 
Last edited:

WyoSyclone

Active member
Re: Datamaster Review plz

Well, the voltage is a bit low... you're running just above battery potential. You could benefit from doing the ECM relay mod (lots of info if you do a search for it).

I see a max of 3.3 KR which isn't too bad, really, if the truck has been sitting for a year with bad gas... especially with some of the data being from a part throttle roll-on from speed, as opposed to a 100%tps WOT.... seems like those part throttle applications are where our trucks are really susceptible to KR.

I'd say not too bad really. I'd pull the plugs and look them over, suck all that old gas out and refill with new and do another run. I don't see anything which would prevent you from doing a WOT run... that will tell us more.

Your IAT temps are low... are you running the stock IC, or A2A? I assume that you are at sea level as well as your baro reading is high.

HTH
 

johnboy89

Member
Re: Datamaster Review plz

Yup at sea level and stock IC with hot wired pump and EGR disconnected for now. It will go back up, I just wanted to see how much of a difference it makes with it disconnected and it's big.

I'll try and get another run this week and post up, looks like some rain this week for us:rant:
 

WyoSyclone

Active member
Re: Datamaster Review plz

I just looked at it. If I were you I'd put a fuel pressure gauge on it and see what the FP is doing under boost. Since the KR is following the boost curve, and only happens at higher boost, I'd assume you've got a fuel supply issue (along with the fact that your INJ DC is reading high).

Check the FP, check the vac lines going to the fuel pressure regulator - if it has a leak you won't get rising rate pressure out of your regulator. If the fuel filter hasn't been replaced recently I'd do that as well.

Also, check to see what your voltage is at your pump harness near the fuel tank. With your ECM voltage running lower than it should be it could be pointing to a weak charging system, which would also drop your fuel supply/pressure (slow running pump).

HTH
 

johnboy89

Member
Re: Datamaster Review plz

I just looked at it. If I were you I'd put a fuel pressure gauge on it and see what the FP is doing under boost. Since the KR is following the boost curve, and only happens at higher boost, I'd assume you've got a fuel supply issue (along with the fact that your INJ DC is reading high).

Check the FP, check the vac lines going to the fuel pressure regulator - if it has a leak you won't get rising rate pressure out of your regulator. If the fuel filter hasn't been replaced recently I'd do that as well.

Also, check to see what your voltage is at your pump harness near the fuel tank. With your ECM voltage running lower than it should be it could be pointing to a weak charging system, which would also drop your fuel supply/pressure (slow running pump).

HTH

So I hooked up a fuel pressure gage to it the other day and pressure seemed to be fine(no dropping at higher boost levels)

As far as the filter looks like it was changed about 13,000mi. ago...... What's the norm on changing these???

I could try some xylene, but think it's real at this point.

I am using the L35 heads, is it possible it might need a tune because of this??????

Can different brands of gas make a difference??? I've been using the cheaper stations for fill up of 93?????

Thanx:)
 

WyoSyclone

Active member
Re: Datamaster Review plz

So I hooked up a fuel pressure gage to it the other day and pressure seemed to be fine(no dropping at higher boost levels)

Thanx:)

You should gain 1lb of FP for every pound of boost... if yours is just hanging the same you've got a prob
 

johnboy89

Member
Re: Datamaster Review plz

You should gain 1lb of FP for every pound of boost... if yours is just hanging the same you've got a prob

It did, was around 39-40 at idle and jumped up at least 10PSI or more couldn't really read it.

The only other thing I can think of is the knock sensor. I'm pretty sure I tightened it more than the 14ft/lb spec.
 

WyoSyclone

Active member
Re: Datamaster Review plz

Just looked at the second run. You're running lean due to the L35's. 11.8afr at 15lb of boost is lean.... need to try getting that down to 10.8 and see if it helps. What other mods did you make when you swapped to the L35's?
 

johnboy89

Member
Re: Datamaster Review plz

Just looked at the second run. You're running lean due to the L35's. 11.8afr at 15lb of boost is lean.... need to try getting that down to 10.8 and see if it helps. What other mods did you make when you swapped to the L35's?

That was the only mod that I did.............

What can I do to get that number down????

Thanx:)
 

WyoSyclone

Active member
Re: Datamaster Review plz

That was the only mod that I did.............

What can I do to get that number down????

Thanx:)

Well, you're flowing more air, so you're running leaner... the only real way to cure it is with a new tune. You may also need slightly larger injectors. I like Code59, but there are other options out there. You might want to contact Hood and see if he has something for you.
 

WyoSyclone

Active member
Re: Datamaster Review plz

Looking at this again due to the L35 packages I'm working on... you're the perfect case study of bolting L35's onto a stock motor.

Your DM file shows the engine running great with no KR up to 18.6 degrees of advance and 15 lbs of boost during short-duration bursts. When you get up into the top of second where the RPMs are climbing more slowly and AFR targets are demanding more from the injectors, is where you see the trouble starting to develop with the tune/parts combo.... the ECM is calling for a 11.8 AFR, which is lean anyway, but your LT counts (formerly BLM) is at +13.3% with an injector DC of 123%.... running way lean with the injectors maxed out.
It would be great to get this motor on Code59 and get the tune straightened out to see how much of a difference would be shown with the correct tune.

I wouldn't run this one very hard until you get the afrs back to a safe range.
 

WyoSyclone

Active member
Re: Datamaster Review plz

Rob:

This is my red/gry 92. I drove it regularly for 9 years. It didn't used to run this way. BLM's were never in the 140's. I have no idea what John changed when he replaced the engine since his purchase other than the L35 heads. He's posted that's it. But I think something else has changed. How about fuel pressure? The Walbro is over 10 years old. It had a stock FPR when I sold it. Stock 18 year old injectors. The car has been sitting for a year after the engine blew. John has recently gotten it running again.

BLM of +13.3 is a BLM of 144. This should set Code 44 if it remains this high over 1 min. But It probably doesn't.


DaveP

Hey Dave,
John says he only switched to the L35's, which would account for what we're seeing in DM. It would be good to ensure that fuel delivery is within spec. It is throwing some codes.
Thanks, Rob
 

johnboy89

Member
Re: Datamaster Review plz

Hey Dave,
John says he only switched to the L35's, which would account for what we're seeing in DM. It would be good to ensure that fuel delivery is within spec. It is throwing some codes.
Thanks, Rob

Yeah the L35's were the only thing I did other then beef up the bottom end. I'm curious has anyone bolted up a set of L35's to a stock engine and been able to run it without a tune??? The FPR, inj. and fuel pump are as they were before, but if it didn't happen before then it's most likely the L35's????? The only codes I have is the EGR and the 42 code from setting my timing.

It'll be parked soon, been thinking about tinkering with the code 59 stuff!!!!!
 

turbodig

Active member
Re: Datamaster Review plz

Well, I've mentioned this a few times before, but if adding the heads didn't move more air, there's really no point in putting them on.

And, since they *do* move more air, you'll need more fuel to match the additional air. The ECM won't just detect that there was a change in airflow (there's nothing there to detect it), so it won't add fuel to match without reprogramming.

The only way this situation could possibly work out, is if the chip that was in it was excessively rich to start with, and the additional head flow matched the amount of overfueling. That's a pretty big set of coincidences to have happen.

Fuel pressure can help, but the reality of the matter is that with stock injectors, 10 psi of fuel pressure will only move afr .1 to .15, tops. If you're 1.0 or more AFR points off, you're not going to fix it with fuel pressure.

The only real way, is to tune the AFR to match the parts, and the only way to do that is in the chip.
 

It's just a six

Super Member
Re: Datamaster Review plz

I would turn up the fuel pressure for now @ least.
Guys have run as high as 60 psi,I have run as high as 55 psi,it helped.
Now w/the 36 lb blue top Ford injectors I have in the engine, I needed to turn down the FP IIRC 36 psi,w/no tune as of yet. But I also added alkycontrol.


With the 36 lb injectors I can go really rich,like 10.2 @ WOT & as lean as 11.8 or so by changing the FP.
 
Last edited:

johnboy89

Member
Re: Datamaster Review plz

I would turn up the fuel pressure for now @ least.
Guys have run as high as 60 psi,I have run as high as 55 psi,it helped.
Now w/the 36 lb blue top Ford injectors I have in the engine, I needed to turn down the FP IIRC 36 psi,w/no tune as of yet. But I also added alkycontrol.


With the 36 lb injectors I can go really rich,like 10.2 @ WOT & as lean as 11.8 or so by changing the FP.

What I did was change the fuel filter and put on an AFPR. Set the PSI as high as 45PSI, didn't really help much.

Rob made mentoin of checking the voltage at the pump, never did that, but made me realize I had a Walbro in the truck and no hot wire, I installed one of those and made a big difference, reduced the knock quite a bit.:D

So maybe I bump the pressure a bit more and I might be fine, attached is my latest file?????

Who sells the blue tops????

Thanx:)

http://rapidshare.com/files/438271757/Test_10.uni
 

WyoSyclone

Active member
Re: Datamaster Review plz

What I did was change the fuel filter and put on an AFPR. Set the PSI as high as 45PSI, didn't really help much.

Rob made mentoin of checking the voltage at the pump, never did that, but made me realize I had a Walbro in the truck and no hot wire, I installed one of those and made a big difference, reduced the knock quite a bit.:D

So maybe I bump the pressure a bit more and I might be fine, attached is my latest file?????

Who sells the blue tops????

Thanx:)

http://rapidshare.com/files/438271757/Test_10.uni

This log doesn't look too bad... your long term is running about 17%, but short terms are OK. To get a good read on whether this is going to work, you really need to run it up through the top of 3rd at WOT... maximum load will happen around 70-80mph and that's where you'll see fueling problems get nasty.

You still really do need a good tune, as you're now running rich at other power settings due to the increased FP... a new tune will set it all straight.
 
Top