diy-wb building question

TurboTony

Active member
I was under the impression that a person could use the 5 volt input for an a/c pressure signal to datalog the w/b. As I understand it the ecm is equipped with this for the quad 4 application.

Is this what Digs code is for or am I way off base here.

Just trying to learn all the factors involved.

Sorry for the dumbass questions, but there are way more to come :grin:


TurboTony
 

leroy

Donating Member
On 2002-02-21 16:09, TurboTony wrote:
I was under the impression that a person could use the 5 volt input for an a/c pressure signal to datalog the w/b. As I understand it the ecm is equipped with this for the quad 4 application.

Is this what Digs code is for or am I way off base here.

Dig's code uses the 5 volt input on pin F14. It's filtered and then spit out in the commanded AFR field in the ALDL data. You still have to do some math, converting A/D counts to volts and then checking that against the v_out table.

Jim
 

BigAl...

Member
Has anybody finished the LED display? I finished mine and I'm having some trouble getting it to work properly. I did the initial test and got 5v at pin 4 and 14 as indicated in the instructions, but when I put the two boards together and it's not showing what it's supposed to.

Ps: I also finished the PCB but there is no way to test that until I get the display working.

TIA
BigAl...

<font size=-1>[ This Message was edited by: BigAl... on 2002-02-22 09:49 ]</font>
 

leroy

Donating Member
On 2002-02-22 09:48, BigAl... wrote:
Ps: I also finished the PCB but there is no way to test that until I get the display working.
Why can't you test it with a voltmeter? If you want you can use a tail light bulb to test the heater circuit. You have to have 13+ volts to get it to work, so have a good power supply or have the car running.

Jim
 

turbodig

Active member
On 2002-02-21 09:26, Tom Servo wrote:
Dig replied to Al that his code was public domain and ok to give out.

I would like to put it in the 50# chips, and people could either use it or forget about it, but that is a grey area, and not really the same as letting someone have a copy of the code. I am selling the chips & making money off of them (not getting rich mind you :wink: ), but I don't want to ruffle any feathers by having this as a 'feature' of my chips, as a possible selling point.

The way I look at it, people are buying the chips anyways, whether or not this feature is in it, but I do feel a bit weird putting something that was generated by DIY/public domain group in my private business calibration. Kinda like people selling the wb 02 setups. Yes they are still keeping it cheap & not very profitable, but it is still taking others' ideas & work.

So Dig, if ya read this anytime soon.. Yea or nay? Just say the word, and I understand if you don't want it in there.


As long as the price doesn't go up with the
addition of the code, no harm done. Offer it
as a free "option", and it's cool.

I'm working on a revised version that will
read real afr out on the desired AFR field,
but at the moment, this would require a 32k
code space. (Which wouldn't really work for
the ultimates)

I may be able to get it into the stock 16k
code space.... stay tuned.

For now, the existing patch works, as long
as you look up the afr values correctly.

For those of you building, it got a lot
easier-

http://www.diy-wb.org

One-stop shopping for all your garage-hack
WB needs. :smile:

Later,

Dig
turbodig@yahoo.com
'91 Sy - 12.08@110
WB design team member - Live free or die!
 

BillC

New member
I'm having the same problem with that URL. Clicking the link ends up at http:www.diy-wb.com (no typo: ".com", not ".org"). I event tried typing it in by hand, in case there was a HTML problem. No dice.

Could the .com site have hijacked the DNS listing? Can anyone please post the direct IP address to the .org site? Or, is the .org site _supposed_ to redirect to the .com site?

Thanks
 

smeagol

Active member
As far as I know, that's correct. It links to the .com site, and all the information there is taken from the original DIY_WB02 setup that Bruce and other DIY guys did up. Pics are in after you click agree etc. It's all there from what I saw.
 

Tydriver

TurboLS6 Powa'
On 2002-03-05 06:40, Tom Servo wrote:
Clicked on your link, worked for me.

Oddly enough I clicked on it this morning and it worked CORRECTLY huh... strange musta been one of those lil gremlins. Oh well....... Anyhow thanks for trying and thanks for posting it Dig.
 

turbodig

Active member
On 2002-03-05 09:18, BillC wrote:
I'm having the same problem with that URL. Clicking the link ends up at http:www.diy-wb.com (no typo: ".com", not ".org"). I event tried typing it in by hand, in case there was a HTML problem. No dice.

Could the .com site have hijacked the DNS listing? Can anyone please post the direct IP address to the .org site? Or, is the .org site _supposed_ to redirect to the .com site?

Thanks

One and the same site... Bob got both the
.com and .org domains.

You most likely encountered a temporary
server "burp"....


Later,

Dig
 

JoeLutz

New member
On 2002-03-06 08:51, Tom Servo wrote:
Tuning tool for anything... car, truck, lawnmower...
LOL lawnmower... Yeah thats what I'm going to use mine for too. Maybe I'll put speedpro on it and use the WB02 to tune it in. :grin: Lookout yard, here I come.
 

BillC

New member
Has anybody finished the LED display? I finished mine and I'm having some trouble getting it to work properly. I did the initial test and got 5v at pin 4 and 14 as indicated in the instructions, but when I put the two boards together and it's not showing what it's supposed to.
Are you asking about the Jaycar display that's available with the TechEdge kit? If so, I finished mine last night. Didn't have any problems with it or with calibrating it.

Three things to check:
First, you have to use the modified instructions that are on one of the photocopied pages that came with the kit. Or, look on his web page for the display:
http://www.techedge.com.au/vehicle/wbo2/wbfmd.htm. There are a bunch of extra bits that come with the kit that you won't need for the TechEdge version.
Second, you need to solder a 1.8 kohm resistor to the back of the processor board to perform the calibrations (the resistor kicks the display into "voltmeter" mode).
Third, you need to follow the modified calibration procedures that are on the same web page listed above.

If you have any more questions, feel free to ask.
 
Top