Help Using an O-scope (oscilloscope)

BoostedSUV

Active member
I just bought a Velleman HPS10 handheld O-scope to try to track down an issue that I'm having with my truck. Does anybody have experience with these? What are some good tips on what to look for, what to check, how to hook it up etc? All the online vids and instructions don't really explain the automotive side of things very well. I was messing with it on my truck and I can get a "heart beat" looking graph but I'm not really sure what I'm looking for. When I bring up RPM's the graph dances all over and sometime flatlines.

I'm trying to determine an RPM specific issue I'm having and I'm trying to pinpoint the source of what's going wrong... TIA



You can talk to me as if I was a complete idiot on this question... I've never used one before. don't be afraid to be simple :tup:
 

BoostedSUV

Active member
Re: Help Using an O-scope (oscilloscope)

this is what I'm working with
SU1HMDAwODgtMjAxMDAyMjctMTU1MC5qcGc.jpg


Here's the probe setup.. there's an aligator clip connected to the shaft, a hook feature to wrap around wire, or a cap comes off to reveal a pin type probe.
SU1HMDAwOTAtMjAxMDAyMjctMTU1MS5qcGc.jpg
 

fauXGT

Brick Pilot
Re: Help Using an O-scope (oscilloscope)

Are you familiar w/ a o-scope? It's like a volt meter that displays the voltage on a floating screen. Should be a volt selection switch.If 12 volts is what your looking at, select the next higher scale, say 20 volts or higher. The 'heart beat' could be D.C. volts swinging up down, from 0 volts to, say 12+ volts. The center horizontal line is 0v reference, so the beat would start at 0v and swing up to peak voltage. Swinging below center would be negative voltage. So A.C. 'sine' wave would swing below 0v to Negative peak V then to 0v,then to positive peak V., to 0v, then to neg V. Logic circuits are viewed with a o-scope probe( usually 5volts). This will display your logic 'ons' & 'offs' for digital data as square, flat top +, or - voltages from center 0 volt reference. This is all from memory from electronics school 21 years ago.
 

fauXGT

Brick Pilot
Re: Help Using an O-scope (oscilloscope)

Just saw probe. The gator clip is ground reference clip on whatever your monitoring. the tip of the probe is the voltage monitor, + or -. Experiment with a known voltage, say 12v. See if you can get the voltage to display on screen. from a battery it should be flat line 12 volts. from a charger, or alternator, or transformer pack, you'll see flat spikes, with little drop offs. The flat top spikes will be the output voltage... i.e. 9 volts, with tiny, low voltage drop offs, say 4 volts. Sorry I wasn't closer. I'd come over & help. It's been a bunch of years since I've touched a scope.
 

BoostedSUV

Active member
Re: Help Using an O-scope (oscilloscope)

I see where I can change the display settings: V/div what is the voltage setting, and I also have a setting for MS/div which assume is milliseconds?
 

BoostedSUV

Active member
Re: Help Using an O-scope (oscilloscope)

Just saw probe. The gator clip is ground reference clip on whatever your monitoring. the tip of the probe is the voltage monitor, + or -. Experiment with a known voltage, say 12v. See if you can get the voltage to display on screen. from a battery it should be flat line 12 volts. from a charger, or alternator, or transformer pack, you'll see flat spikes, with little drop offs. The flat top spikes will be the output voltage... i.e. 9 volts, with tiny, low voltage drop offs, say 4 volts. Sorry I wasn't closer. I'd come over & help. It's been a bunch of years since I've touched a scope.

it's been 28 years and I've never touched one... lol Just one more piece of test equipment to track down an issue with a these PITA trucks! :lol:
 

fauXGT

Brick Pilot
Re: Help Using an O-scope (oscilloscope)

V/DIV would be the voltage peak, up/down selection. The MS/DIV horizontal setting for, you are correct,.. millisecs.
 

BoostedSUV

Active member
Re: Help Using an O-scope (oscilloscope)

Now can I use any ground for the probe or should I be using the ground for what I am testing, ie O2 sensor, Map sensor, tps, injectors etc?
 

gkrcr882

SyTyless......for now!
Re: Help Using an O-scope (oscilloscope)

Depends on what you're checking as well. DC sensors produce a square wave (hall effect CKP and CMP, TPS, MAF, MAP), AC produces a sine wave (ABS sensors). Ignition events have something that sort of resembles a heartbeat (goes down, then up, then coil oscillations). Something like a TPS is going to have a DC output on a 5v scale, whereas secondary ignition is going to be on a much higher scale.
 

dgoodhue

BuSTeD 4.3
Re: Help Using an O-scope (oscilloscope)

I see where I can change the display settings: V/div what is the voltage setting, and I also have a setting for MS/div which assume is milliseconds?

Yes Volts per Division (lines on the X axis or vertical), Millisec/Div is my guess what the other is. If you zoom to far it can be confusing .

For ground you can use teh return line to the injector, the ECM ground goes to the back of the cylinder head, so in theory that should work as well (unless the injectors circuitry is isolated)
 

Quickstop [UK]

Combating adversyty.
Re: Help Using an O-scope (oscilloscope)

If you're looking at the rpm and the ignition voltage then as you increase RPM you're going to get a crazy effect on the screen as the rpm increases because your base timing (Timebase) will not be valid.

idle at 800 rpm = .075 seconds = 75 milliseconds so 100 ms/div should be about right... You'll only get an ignition/injector pulse every second rotation so actually it'll be twice the time so 200ms per div is the idle setting you need.

At 2400 rpm (one of your problem spots right?), your timebase should be

60/2400 = .025 so you might need to change it to 100ms/div

You need to set it for one rpm with the timebase ms/div and the v/div and keep it constant. Unless you only increase the rpm slightly then your timebase will be off as ilustrated above.

Pick an RPM where you have no problem that you can maintain and get a steady picture on the screen - this will show you the ignition signal.

The heartbeat suggests that the picture is moving along? Your timebase needs to be adjusted slightly to get the picture steady.

Then you need to set the truck to run at the RPM where you get all your problems. If it's an ignition issue then you will see that the ignition signal is messed up whereas it should be exactly the same.

What voltage are you able to measure? 12v DC/AC is way too low - ignition voltages are going to be in the KV ranges.

Have you tried measuring the ignition yet or are you just focussing on injectors? You should be able to get the square wave pretty easily with the injectors. Ground it to the head of the block and use the probe on one of the wires from the injectors. Your voltage should be set at 20v across the screen - don't know how many divisions there are.

If you don't get a square wave then that would be a surprise.

I'll have a look at the manual for that scope and try and be more helpful.

I'm also very close to finding out if I am going to be moving to Wilmington,Delaware, with work (Keep your fingers crossed for me - 19th April is the planned arrival date) which I believe is close to NJ so if I come over then I'll come up and try and help seing as I was one of those that talked you into buying an o scope! . I did a BENg in Electronics and Electrical engineering and this is getting my juices flowing :D
 

Quickstop [UK]

Combating adversyty.
Re: Help Using an O-scope (oscilloscope)

OK I just googled it and it looks like a nice piece of kit but you'll struggle to look at your secondary ignition because it only goes up to 20v.

The instruction manual is in pdf here

You should however be able to measure the primary ignition voltage though and that will tell you if your primary ignition signal is correct. This would be the low voltage side of the coil.

In searching, I found this article as well which may be of interest...

VW Golf running rough after a few km

In summary, all the ign and injection modules were fine but the relay from the steering column was skewy and gave a messed up power supply to the ECM which in turn caused problems with the ign timing.

Food for thought?
 

turbodig

Active member
Re: Help Using an O-scope (oscilloscope)

Using a scope to diagnose a problem requires a bit of knowing what you're looking for.

What you *could* look for:

Verify that the 12v supply and IGN lines to the ECM aren't noisy. (should be a flat DC line)

The following should be done when the problem is manifesting itself:
Verify that the EST and REF lines aren't excessively noisy both at the ECM and the ignition module.
Verify that there isn't any noise/weird pulse train at the injectors. Verify all injectors see the same pulse train.

Get an inductive clamp (you can probably use a timing light clamp, although you may need to attenuate it to read properly). You can buy clamps already made for ignition... I think pico tech offers some.

With the inductive clamp, look at ignition voltage at each cylinder when the problem is happening. Check to see if any cylinders are "breaking down" in terms of ignition voltage.

All that being said, given all the stuff you've replaced, my gut tells me that you have a mechanical problem of some sort- valvetrain, timing set, lifters, springs.... something along those lines. It won't hurt to do the above tests, at least it will eliminate all of these as a potential problem.
 

BoostedSUV

Active member
Re: Help Using an O-scope (oscilloscope)

Bunch of good info guys... When I'm home in front of the truck with the o-scope I hand hopefully I can make some more sense of it. :tup:
 

BoostedSUV

Active member
Re: Help Using an O-scope (oscilloscope)

Quickstop, Willmington, Deleware is less than 2 hours from me. I will cross my fingers for you! Haha I'd love to have another hand helping me out! :tup:
 

The_Bronze

Donating Member
Re: Help Using an O-scope (oscilloscope)

I'm new to the forums, but am very handy with DSOs in automotive applications. I also have a couple of DSO manuals that are automotive specific. PM me and I'll send you one for the cost of shipping.

I love the DSO. With the appropriate accessories, I am looking at cranking and running compression (real time in the cylinder) that would show cam timing, cam, spring, and valve problems via a high PSI rated pressure transducer, Relative compression testing (5 minutes without pulling a plug), head gasket leaks (compression into the cooling system) and a whole host of tests..

The trigger function (and the on trigger setting) will become your friend. As it was stated below, Knowing what is suppose to be happening is 1/2 the battle. The other half is being able to properly set up the scope to see it. Keep in mind that most DSOs have a refresh rate and that means you are not seeing "real time, every time" screen shots. You are missing periods when the screen is refreshing. Good info to know and understand, that's why the trigger function is so important. The scope takes time to master, and the best thing you can do is practice on a known good signal first (steady DC, Square wave, AC then a dynamic pattern such as MAP, TPS and such.

Some tools of the trade:

scopesandmeters.jpg


The low amp clamp is under $100. The power probe (Highly recommended) is just a bit over that.

Here is a cam and crank sensor comparison:

camcranksensor.png


The amount of time in between these signals represents the cam/crank synch. In this case, this was after the dist was installed correctly. It was one tooth off (and cranked over as far as it would go). The computer can interpret these signals in different ways and produce a code for the wrong component if the signal "breaks up".

Here is a cranking voltage/current signal:

voltageandcurrentwaveform.png


You can see that there is an initial inrush of current (current goes high to 800A) and the voltage drops to about 8V. In this case, this was long enough to perform a PCM reset and was keeping his monitors from running. Battery tested good, sounded good but the starter bearings were defective. Plenty of "diagnostics" and parts were thrown at this one before I saw it.
 

The_Bronze

Donating Member
Re: Help Using an O-scope (oscilloscope)

You should however be able to measure the primary ignition voltage though and that will tell you if your primary ignition signal is correct. This would be the low voltage side of the coil.

The Primary waveform will closely mirror the secondary output, but the scale will, of course be completely wrong. I hardly ever have to look at secondary. Plus, that is an "artform" all to itself. What works very well is using a current probe to watch the current waveform. A nice sloping pattern that is regular (trigger it off of #1) and shows all 6 waveforms indicates good primary control. A waveform that rises sharply in the very beginning indicates a partially shorted coil. Those are hard to diagnose without the waveform. You can also watch the bypass line to ensure that the computer is taking control (at around 400 rpm) and is providing proper spark advance.
 
Top