Help with Datamaster file

ssullivan556

New member
So here are my problems, stock truck with 81k miles:
1. The truck has a rough idle, only sometimes. I am guessing that this is dependent on whether it is in open or closed loop. What should I do to check the o2 sensor?
2. The truck has trouble shifting 2-3 and 3-4. You only see the 2-3 shift in the file but 3-4 feels the same. It revs to about 4000 rpm, hangs there for a few seconds like it wants to shift and then it shifts because I usually let off the throttle, out of fear of breaking something. As you can see in the DM file it is going above 15 psi and opening the wastgate and then dropping back to mid 14s and repeating. I was thinking that this would be caused by a vacuum leak. Somebody suggested that it might be the diaphram in the wastgate leaking.
3. STerm and the code 44 shows that it thinks it is running lean after I let off the throttle and was cruising. I recently replaced the plugs and checked them after 50 miles or so and they looked perfect so I don't think it is actually lean. o2 sensor again?
4. Wastgate Duty Cycle is 100% at idle. This means that is closed right? I thought it would be partially open.
5. What should I do about the random data errors? Are these errors in the ECU or just with DM or the ALDL cable?
Here is the file:
http://rapidshare.com/files/400205658/5_8_10.uni

Thanks for the help!
 
Last edited:

The_Bronze

Donating Member
Re: Help with Datamaster file

I downloaded the file, I'll try to stuff it into the black box and see what it spits out.
 

The_Bronze

Donating Member
Re: Help with Datamaster file

1) Is your local baro really 23.9? I run around 29 around here so it stands out.

2) Idle vacuum is really low. Baro-Map=Vacuum. The Math is right, but the vacuum is rather low. I don't have experience in high altitude areas, maybe this is vacuum level is rather normal for such low Baro?

3) Your O2 sensor seems to respond correctly. It is showing rich at idle, but as you put a load on it, it falls off until it is lean. Low fuel pressure, not enough pump, plugged filter?

4) Idle motor looks good at 15 counts. I don't see a vacuum leak at idle there or the number would be lower. It rises slightly for you putting it into gear which is normal as well.

5) At about 60 seconds, the Park/Neutral switch indicates a switch from in gear to park or neutral. Looks like you were moving around 60mph, so I hope it wasn't park...

There's more in the file, but I need to go to bed. :zzz:

6) Your battery system voltage drops as you go into a load, the same time as your fuel system goes lean. Coicidence? Likely not.

7) Your short term goes up trying to bring up the O2 sensor voltage. At the coasting portion on the end, you are still lean.

Your shifting issue should be addressed starting with TV cable adjustment and check the governor.
 

The_Bronze

Donating Member
Re: Help with Datamaster file

I guess judging by your sy pictures, you live pretty high up. Maybe your Baro/Vacuum is correct. It wouldn't hurt to verify it though.
 

ssullivan556

New member
Re: Help with Datamaster file

I live at 7000ft but 23.9 is too low if that is measured in mmHg. Does the computer get its baro reading from the MAP sensor? Is there a way to test that? I know I didn't shift into park, maybe I missed OD and went to neutral. Does my boost around where the truck is trying to shift look OK? It seems like that wavy line is a bad thing. I have a new fuel filter I will put in. How exactly do I go about adjusting the TV cable? I am new to automatics, I prefer manuals. Is there an issue with the random data errors?
I am leaving for a month so probably will not be replying during this time period. Thanks for taking a look at the file.
 

The_Bronze

Donating Member
Re: Help with Datamaster file

23.9 is inches of mercury or inHg. That equals about 600 millimeters of mercury or mmHg. I think it sounds like it could be right depending upon conditions. I've never lived at altitude, must suck (or hard to suck???), but you should compare to your local airport information to validate it.

Your P/N switch could be out of adjustment a bit. I would look at that PID (P/N parameter) and wiggle the lever a bit and see if it changes on you. Adjust as necessary.
 

Don W.

Stab it and steer it
Re: Help with Datamaster file

Barro is correct if he's at 7000'. You loose 1" per 1000'.

Shifting issue maybe TV cable adjustment?

DTC errors are as reported to DM by the ECU.

Intake air temps seem high to me. Is your IC pump hot wired? Working correctly?

Also motor seems to be running a bit on the hot side. What t-stat do you have?

I'm far from a DM expert but that's my :2cents:
 

turbodig

Active member
Re: Help with Datamaster file

So here are my problems, stock truck with 81k miles:
1. The truck has a rough idle, only sometimes. I am guessing that this is dependent on whether it is in open or closed loop. What should I do to check the o2 sensor?
2. The truck has trouble shifting 2-3 and 3-4. You only see the 2-3 shift in the file but 3-4 feels the same. It revs to about 4000 rpm, hangs there for a few seconds like it wants to shift and then it shifts because I usually let off the throttle, out of fear of breaking something. As you can see in the DM file it is going above 15 psi and opening the wastgate and then dropping back to mid 14s and repeating. I was thinking that this would be caused by a vacuum leak. Somebody suggested that it might be the diaphram in the wastgate leaking.
3. STerm and the code 44 shows that it thinks it is running lean after I let off the throttle and was cruising. I recently replaced the plugs and checked them after 50 miles or so and they looked perfect so I don't think it is actually lean. o2 sensor again?
4. Wastgate Duty Cycle is 100% at idle. This means that is closed right? I thought it would be partially open.
5. What should I do about the random data errors? Are these errors in the ECU or just with DM or the ALDL cable?
Here is the file:
http://rapidshare.com/files/400205658/5_8_10.uni

Thanks for the help!

Stock chip in it, or something else?
 

The_Bronze

Donating Member
Re: Help with Datamaster file

1) Look at the govenor (under the round cover that is held in by a snap ring). Here is a picture of the location. Easy Squeezey:

A picture:
http://www.google.com/imgres?imgurl...s=com.microsoft:en-us:IE-SearchBox&tbs=isch:1

A generic description:

http://www.dragracingonline.com/technical/vi_9-bm-1.html

2) Adjust the TV cable. Here is a write-up on the procedure. You just need to do step 4:

http://www.tciauto.com/Products/Instructions/instructions/gm_tv_cable_adjust.htm
 

The_Bronze

Donating Member
Re: Help with Datamaster file

1. The truck has a rough idle, only sometimes. I am guessing that this is dependent on whether it is in open or closed loop. What should I do to check the o2 sensor?

Give us a DM file that has both rough and smooth idle. Let me know where the change occurs. Graph O2 crosscounts, O2 sensor and MAP. Typically the rough portion going into closed loop isn't due to the O2 sensor, since they typically fail indicating lean and the rich compensation tends to smooth the idle out.
 

ssullivan556

New member
Re: Help with Datamaster file

Ok when I get back in a month I will try all this stuff. Thanks for all the good ideas. I am currently on the other side of the country and am about to go internetless for the next month.
 

socal

New member
Re: Help with Datamaster file

Sounds alot like my exact situation but i have 46k, and im 99% sure its just the tranny is slipping and needs to be rebuilt.
 

ssullivan556

New member
Re: Help with Datamaster file

OK so I am back and today I adjusted the TV cable as instructed on that writeup. I also hotwired the IC pump (it was not hotwired at the time when I got that dm file). My brakes are not working well so I am not going to do any at-speed testing. I am going to have to work on those for a while before I am ready to test it. Over the past month I have forgotten where I placed my ALDL cable so it might be a while before I find that and get you a dm file of the idle. I'll get to the fuel filter as soon as I figure out the brakes (which may take a while).
Thanks for your help!
Edit: I also replaced the fuel filter today. It feels the same. It just seems to stop pulling at 4000 rpm or so in second (and I assume third, but I do not have a good place to take it up to 80+ close to my house). What exactly should I look for on the governor? All that is left on my list of things to do is check governor, get some more dm data, check fuel pressure and change the transmission filter. Any more ideas? How can I test if the transmission is slipping? The truck has the stock t-stat and chip as far as I know.
 
Last edited:

ssullivan556

New member
Re: Help with Datamaster file

I found my ALDL cable and took the Syclone for a drive today. I got it idling cold and warm. Are both OK? Perhaps I am imagining the increased roughness after it is warm. This file also has lots of driving around and one short full speed blast at the end. There isn't enough road to get out of second gear near my house though. I got a hot flag part way through, this sounds bad. Also, does my boost seem sluggish to anybody? The fuel filter did increase my voltage up to normal levels, the old one was pretty clogged up. I also was looking around the service manual and found something that said "Engine RPM and car speed limited or restricted at high speeds, performance when accelerating from a standstill normal. Engine may over-heat. Visual examination of converter may reveal a blue-color from overheating." This is due to torque converter stator assembly being locked in both directions. What do you think of that? That seems to describe all of my problems.
The new file:
http://rapidshare.com/files/413908368/8_19_10_driving_and_idle.uni
The old file (I think it expired on the old link):
http://rapidshare.com/files/413908350/5_8_10.uni

Thanks a lot.
 

WyoSyclone

Active member
Re: Help with Datamaster file

What mods on the truck??
I just looked at the file and didn't see anything out of whack, other than it's shifting a bit early at WOT (4175). Voltage is good (14.2 volts), IAT's are very low (are you running A2A or stock?). Engine temp is good - only up to 185. It goes from a cold start high idle to a normal idle, good spark advance, 3.2 KR max.
 

ssullivan556

New member
Re: Help with Datamaster file

The truck is completely stock. The IC pump is hotwired on so in the first file that explains the IAC temps. It also seems to shift ok from 1 to 2 but it does not from 2-3 and 3-4. It pulls hard up to around 4000 rpm and then seems to lose power and hang at that rpm for a long time. This can be seen in the first file. This seems to be described by the service manual as the torque converter stator assembly being locked up. Have you heard of this happening? Do you know what causes it? How can I be sure this is the problem?
Thanks for the help.
 

WyoSyclone

Active member
Re: Help with Datamaster file

It also seems to shift ok from 1 to 2 but it does not from 2-3 and 3-4. It pulls hard up to around 4000 rpm and then seems to lose power and hang at that rpm for a long time. This can be seen in the first file.QUOTE]

I hadn't looked at that first file in a long time... it's not doing that in the second file. What changed mechanically between the two logs? The P/N flag that is activated in the first file is probably a clue.. I'll have to wait till I can look at the service books tomorrow to check on that.
 

ssullivan556

New member
Re: Help with Datamaster file

The reason it didn't happen is the second one is because I ran out of pavement to keep going. It was just starting to stop accelerating the instant I let off. Only the last data point or two will be showing this symptom. I am sure that it was starting to happen though.
 

ssullivan556

New member
Re: Help with Datamaster file

Somebody also suggested that it may be the fuel pump. What do you guys think of that? It makes sense since the fuel filter was clogged. Any thoughts? I guess the next thing to replace will be the fuel pump once I get the brakes figured out.
 
Top