Knock and Ultimate

kwick6

Donating Member
On 2001-11-12 19:37, TookyCat wrote:
Thanks for your excellent instructions. A few questions. How important is it to create a seal inside the funnel with the vacuum hose? If I run my truck with the AFPR line open, it will virtually stall and die.
You don't need to seal it, just let it lay in there.
You've pulled the vac line of the afpr, your truck stalled?? hmmm don't think so.
Wouldn't the same thing happen if I have a big hole in the middle of the funnel?
It shouldn't stall, actually it will cause your engine to rev pretty high...try it.
Also you say to dump the last 1/3 of the can into the funnel so the motor stalls. What do you do with the rest once the motor has stalled?
It will take just about 1/3 of a can to get it to stall, and after it stalls you can pour whatever is left in.
Do you just dump it all in regardless? Or does it suck up that last 1/3 at a very fast rate?
Yes your engine will be revving so high once you stop drawing it in with the hose thing, it will take almost all the rest to stall it out. If it doesn't stall just shut it off.
Finally how come you suggest 2 hrs soak time while other places have said 15 or 30 minutes?
Just extra time to let the stuff work.
And what difference will/might I notice once this is all done, I mean what specifically should I look for? Thanks.

It removes carbon buildup and stuff that just causes your engine to be more prone to detonation. I would suggest you do it, change the oil and see if you notice an improvement then let us know.

Scott
 

Falco

Donating Member
Josh,

Just checked my emission label, and it says "PCV inlet" on the driver side. It's a metal pipe comming out from the valve cover, which had the rubber hose connected to (now I'm using a breather). The metal pipe has a 90 degree in it.

AFAIK there were two types of Emission labels, one for CA and an other one for any other state. Don't know the CA one, but I doubt it's using a third PCV valve.

Rgds,
Falco
Sy #2613
 

V

Donating Member
Get out your copy of the "Service Manual Supplement." Page 6E3-C13-1 has an illustration of the PCV system. The label might be GM's standard issue for 4.3L "Z" motors. If I'm not mistaken, the normally aspirated motor has a PCV valve on the driver's side.

_________________
V-
<A HREF=http://www.sytyarchives.com/database/viewuser.php?id=126>Sy1264</A>

fe44e394.jpg


<font size=-1>[ This Message was edited by: V on 2001-11-14 06:53 ]</font>
 

Daron

Active member
On 2001-11-14 05:20, Falco wrote:
Josh,

Just checked my emission label, and it says "PCV inlet" on the driver side. It's a metal pipe comming out from the valve cover, which had the rubber hose connected to (now I'm using a breather). The metal pipe has a 90 degree in it.

AFAIK there were two types of Emission labels, one for CA and an other one for any other state. Don't know the CA one, but I doubt it's using a third PCV valve.

Rgds,
Falco
Sy #2613

Falco, you have hit on the key... I think some folks see the letters "PCV" and automatically assume it is referencing the PCV valve. Positive Crankcase Ventilation system comprises more than just the valve. Suffice to say, there are only two valves on the SyTy....
 

Tooky

Serious about performance
On 2001-11-14 06:48, V wrote:
Get out your copy of the "Service Manual Supplement." Page 6E3-C13-1 has an illustration of the PCV system. The label might be GM's standard issue for 4.3L "Z" motors. If I'm not mistaken, the normally aspirated motor has a PCV valve on the driver's side.
Interestingly offtopic find, the 93 Typhoon Service Manual Supplement lacks the entire 6E Drivability and Emissions section. What a useless manual compared to the 91 Syclone S.M.S. and the 92 Sonoma GT/Syclone/Typhoon S.M.S.! I am glad the 93 Typhoon S.M.S. is not the only one I have. I wonder why they did that.
 

smeagol

Active member
yes...no...

I'm still working on the stock motor 50# chip, and I'm working cam/head 50# setups. I have sold a few custom chips, but I can't guarantee anything. I usually leave out boost control options, and focus more on fueling options.

The 50# stuff for stock motor with bolt ons is coming along nicely, but I'm not about to officially have a full on chip setup available for the 50s at this point.

Brian G
 

Tooky

Serious about performance
In what case would you want to use V7? And when purchasing from the current "STG" distributor (ARAutosports I beleive), do you get to specify V6 or V7 or is only V7 being produced any longer?

<font size=-1>[ This Message was edited by: TookyCat on 2001-11-29 02:18 ]</font>
 

JoeLutz

New member
BG,
What is the eprom ID for V6 and V7?
Thanks

_________________
A FEW PROJECTS
93 Typhoon
67 VW Bug Judson Supercharged
67 Chevy Stepside (in body shop)
68 Camaro RS/SS convertable 396ci
88 Zuk
91 MR2 Turbo (sold)
www.sytycentral.com

<font size=-1>[ This Message was edited by: joeelutz on 2001-11-29 12:58 ]</font>
 

Richard Le

New member
There should be a white sticker on the chip specifying which version it is. I have it on mine, and it says "V6".
 

93 foons

New member
Re: Knock and Ultimate

Are you out there Brian? I have a ultimate chip in my 93, and on a dyno it dumps way too much fuel at low rpm's. I have the fuel pressure down to 42psi and it helped a little. Help !!!!!
 

crazy151drinker

New member
Re: Knock and Ultimate

Wow, old post LOL.

But I dont remember reading about the top down cleaner....something else to do over the Christmas break. Good info once again...
 
Top