LC-1 Install Question

werbicki

<User Title Goes Here>
I've been searching the forums but I haven't been able to find an answer. If I replace the stock oxygen sensor with the LC-1, do I have to do something to keep the check engine light from coming on?

Also I was hoping someone could verify my wiring:

1. Red (12v Supply) goes to 12v Ignition Power.

2. Blue (Heater Ground) goes to seperate ground on the frame.

3. White (System ground) goes to seperate ground on the frame, or B9 on ECU if using DIG's patch. Edit: don't connect this to the white ground wire on existing oxygen sensor, just leave both white wires safely taped away.

4. Yellow (Analog Out 1) goes to black wire (sensor signal according to the Innovate manual) on existing oxygen sensor.

5. Brown (Analog Out 2) goes to AFR guage, or F14 on ECU if using DIG's patch, or is just ignored for later use.

6. Green (Analog Ground) goes to seperate ground on the frame or B9 on ECU if using DIG's patch.

7. Black (Calibration Wire) goes to LED / Calibration Switch.

Not sure why you would send the system ground to the existing oxygen sensor's heater ground, but I found it in this thread: http://www.syty.net/forums/showthread.php?t=45203&highlight=lc-1+install

Right now I an just trying to replace the stock oxygen sensor so I'm not planning on using DIG's patch yet. I'm thinking of seperate grounding everything.

Any help for a newbie to the tuning space would be greatly appreciated!

Paul
 
Last edited:

turbodig

Active member
Re: LC-1 Install Question

werbicki said:
I've been searching the forums but I haven't been able to find an answer. If I replace the stock oxygen sensor with the LC-1, do I have to do something to keep the check engine light from coming on?

Also I was hoping someone could verify my wiring:

1. Red (12v Supply) goes to 12v Ignition Power.

2. Blue (Heater Ground) goes to seperate ground on the frame.

3. White (System ground) goes to white ground wire on existing oxygen sensor (have to test which white wire is ground vs. which white wire is 12v heater power), or seperate ground on the frame, or B9 on ECU if using DIG's patch.


Noooo. The wires on the stock o2 are 2 heater wires, and the sense wire. Ground comes
from the downpipe. I wouldn't connect anything to the heater wires.

Ground white to chassis, somewhere away from blue. Closer you get blue to the battery,
the better.

4. Yellow (Analog Out 1) goes to black wire (sensor signal according to the Innovate manual) on existing oxygen sensor.

True. You also have to make sure the LC-1 is programmed to simulate the 0-1v of a stock O2.

5. Brown (Analog Out 2) goes to AFR guage, or F14 on ECU if using DIG's patch, or is just ignored for later use.

6. Green (Analog Ground) goes to seperate ground on the frame or B9 on ECU if using DIG's patch.

7. Black (Calibration Wire) goes to LED / Calibration Switch.

Not sure why you would send the system ground to the existing oxygen sensor's heater ground, but I found it in this thread: http://www.syty.net/forums/showthread.php?t=45203&highlight=lc-1+install

Right now I an just trying to replace the stock oxygen sensor so I'm not planning on using DIG's patch yet. I'm thinking of seperate grounding everything.

Any help for a newbie to the tuning space would be greatly appreciated!

Paul

Something you might want to look into... I posted some already patched stock bins,
so you can run stock calibrations and get the WB data.

http://www.syty.net/forums/showthread.php?t=46139&highlight=stock+patch
 

werbicki

<User Title Goes Here>
Re: LC-1 Install Question

turbodig said:
Something you might want to look into... I posted some already patched stock bins,
so you can run stock calibrations and get the WB data.

http://www.syty.net/forums/showthread.php?t=46139&highlight=stock+patch
Thanks for the advice on the heater wires, the other post was confusing me. Given what you said I am going to leave the other two white cables disconnected. Will this cause an error code in the ECU?

I don't think I have the equipment to update the ECU with you're patched stock bin, but, I will definately give that a try when I do get there. Thanks for all of your hard work on integrating wideband, it makes running our trucks that much easier!

Paul
 

werbicki

<User Title Goes Here>
Re: LC-1 Install Question

I was also worried that the black wire on the existing oxygen sensor wasn't correct but I can see now that it is. I found the following info on the existing oxygen sensor:

Oxygen Sensor connector vs. Syty connector block (On the oxygen sensor the connector labels each wire A, B, C):

Cable A, white, is heater 12v ignition, conencts to pink/black on Sy harness.

Cable B, white, is heater ground, connects to black with white stripe on Sy harness.

Cable C, black, is the oxygen sensor signal, connects to purple on Sy harness.

Thought I would share it for anyone else thinking of trying this mod.

Paul
 

turbodig

Active member
Re: LC-1 Install Question

werbicki said:
Thanks for the advice on the heater wires, the other post was confusing me. Given what you said I am going to leave the other two white cables disconnected. Will this cause an error code in the ECU?

I don't think I have the equipment to update the ECU with you're patched stock bin, but, I will definately give that a try when I do get there. Thanks for all of your hard work on integrating wideband, it makes running our trucks that much easier!

Paul

ECM doesn't care about the heater wires... just the voltage and the switching of the sense line.

Send me a stock MEMCAL and $30 and I'll send ya back a patched stock memcal. No equipment required.
 

werbicki

<User Title Goes Here>
Re: LC-1 Install Question

turbodig said:
ECM doesn't care about the heater wires... just the voltage and the switching of the sense line.

Send me a stock MEMCAL and $30 and I'll send ya back a patched stock memcal. No equipment required.
Sweet deal!

Is it safe to hook everything up to the ECM without the patched stock memcal? If so I'll hook it up tonight and start shopping around for an extra stock MEMCAL to send your way.

I noticed a good diagram on this thread which I'll probably end up following: http://www.syty.net/forums/showthread.php?t=44504&highlight=lc-1

And, of course, this link too: http://digware.lunarpages.com/digware/wbhookupinst.html

Paul
 
Last edited:

turbodig

Active member
Re: LC-1 Install Question

werbicki said:
Sweet deal!

Is it safe to hook everything up to the ECM without the patched stock memcal? If so I'll hook it up tonight and start shopping around for an extra stock MEMCAL to send your way.

Paul

Yep.. The ECM normally ignores that input.

If you find an old hypertech or JET chip or something like that, it'll work too. I just need something for a core.

You could also get these two:

http://www.moates.net/product_info.php?cPath=25_36&products_id=32

http://www.moates.net/product_info.php?cPath=26&products_id=39
 

turrrbo6

Member
Re: LC-1 Install Question

also keep in mind that the wideband that comes from innovate will get too hot in the stock o2 bung. I moved mine down near the tranny and solved my problems. Lee
 

werbicki

<User Title Goes Here>
Re: LC-1 Install Question

turrrbo6 said:
also keep in mind that the wideband that comes from innovate will get too hot in the stock o2 bung. I moved mine down near the tranny and solved my problems. Lee
I read that alot of guys are running it in the stock location without any problems. I guess I'll have to wait and see what happens.

Did you try the HBX-1 heatsink (about $100 from Innovate) or fabricating a heatsink like they suggest in the manual?

Paul
 

turrrbo6

Member
Re: LC-1 Install Question

werbicki said:
I read that alot of guys are running it in the stock location without any problems. I guess I'll have to wait and see what happens.

Did you try the HBX-1 heatsink (about $100 from Innovate) or fabricating a heatsink like they suggest in the manual?

Paul
actually I contacted Hans @ Innovate and he suggested it. They claim their sensor is only good to about 900-950 degrees. Lee
 

ashman

------
Re: LC-1 Install Question

turrrbo6 said:
also keep in mind that the wideband that comes from innovate will get too hot in the stock o2 bung. I moved mine down near the tranny and solved my problems. Lee

interesting...what problems were solved by moving the 02 sensor?

LOTS of us have the (insert o2 sensor here) in the stock local with no problems.
 

turrrbo6

Member
Re: LC-1 Install Question

ashman said:
interesting...what problems were solved by moving the 02 sensor?

LOTS of us have the (insert o2 sensor here) in the stock local with no problems.
the problem I had was the display on the gauge after a high boost pass would read (---). moving mine down corrected it. Lee
 

werbicki

<User Title Goes Here>
Re: LC-1 Install Question

turbodig said:
Yep.. The ECM normally ignores that input.

If you find an old hypertech or JET chip or something like that, it'll work too. I just need something for a core.

You could also get these two:

http://www.moates.net/product_info.php?cPath=25_36&products_id=32

http://www.moates.net/product_info.php?cPath=26&products_id=39
Is it possible to get these from the junkyard? I was thinking I could take one out of a Sonoma or Blazer, but I'm not sure if they would have the same equipment.

Paul
 

werbicki

<User Title Goes Here>
Re: LC-1 Install Question

Well I got almost everything installed and setup! I didn't end up hooking the white and brown wires up to the computer, ran out of time. I ended up bringing everything into the cab and ran a single wire back out for the simulated narrowband. Grounded everything to the frame behind the kick panel next to the parking brake. Put the calibrate switch and LED in the dash. Everything worked first time!

Next step, hook it up to the computer, apply the patch and do some runs with DataMaster to see why I lose so much power at WOT.

BTW, I put it in the stock location and it seemed to run just fine.

Paul
 

turbodig

Active member
Re: LC-1 Install Question

werbicki said:
Is it possible to get these from the junkyard? I was thinking I could take one out of a Sonoma or Blazer, but I'm not sure if they would have the same equipment.

Paul

If you find a junkyard Sy or Ty, yes...

That's the only valid application.
 
Top