PLX O2 sensor location

92 Ty 1173

Active member
I made a 3" dp, welded up the O2 bungs, one in the stock location and one about 6" behind it, so 12" behind the turbo. So I go to install the gauge and see that PLX recommends the sensor is 36" downstream from the turbo. F*&k, s*&t!! So my question is how critical is it that the sensor is not 36" from the turbo? Do I need to get another bung and weld it in? If so at least I was smart enough to section and v-band the dp so it won't be too hard to remove.
 

Syclone22

Member
Re: PLX O2 sensor location

Some wideband sensors are installed right after
the turbo outlet but it may shorten the lifespan
of the sensor i installed mine after the oem 02
bung and it still works great it depends on what
you are willing to do or follow the instructions ...
 

jpz06

New member
Re: PLX O2 sensor location

Some wideband sensors are installed right after
the turbo outlet but it may shorten the lifespan
of the sensor i installed mine after the oem 02
bung and it still works great it depends on what
you are willing to do or follow the instructions ...

X2 on that,did mine right after the stock 02, works great.:tup:
 

sharkbait

New member
Re: PLX O2 sensor location

I made a 3" dp, welded up the O2 bungs, one in the stock location and one about 6" behind it, so 12" behind the turbo. So I go to install the gauge and see that PLX recommends the sensor is 36" downstream from the turbo. F*&k, s*&t!! So my question is how critical is it that the sensor is not 36" from the turbo? Do I need to get another bung and weld it in? If so at least I was smart enough to section and v-band the dp so it won't be too hard to remove.

mattw discussed this a few months ago. i know alot of people have the plx o2 in the stock location on the dp. i called plx and they said the o2 could have failure down the road or give a reading that isn't accurate cause its calibrated to be 33inches not 4 inches from the trubo:dunno:so i went with plx suggestion. i plugged the stock o2 bung and moved it 33inches down the dp. its around were the tranny pan starts. and it should be on the top side of the pipe.....AND angled away from the flow of exhaust. ill look for the post.
 

nallj92

Active member
Re: PLX O2 sensor location

actually PLX instructions state 24 inches, but I would just run it up top, anything after the turbo will be fine.
 

92 Ty 1173

Active member
Re: PLX O2 sensor location

I really don't want to drop the exhaust again but it is my f'-up so I guess I'll have to get another bung and weld it up. That's what I get for not completely reading the instructions first. Maybe I'll get an EGT sensor from plx and stick it in the empty spot.
 

mattw

Active member
Re: PLX O2 sensor location

I really don't want to drop the exhaust again but it is my f'-up so I guess I'll have to get another bung and weld it up. That's what I get for not completely reading the instructions first. Maybe I'll get an EGT sensor from plx and stick it in the empty spot.

Don't feel bad.. I did the exact same thing and had to pull the downpipe back out. Don't forget to keep it on the top of the pipe and at the recommended angle..

72_WB_O2_Complete.JPG
 

sharkbait

New member
Re: PLX O2 sensor location

I really don't want to drop the exhaust again but it is my f'-up so I guess I'll have to get another bung and weld it up. That's what I get for not completely reading the instructions first. Maybe I'll get an EGT sensor from plx and stick it in the empty spot.

dude, dido. no biggie. i think i had my dp out 10x. part of the fun.....right? :rotf:

and thanks for OP mattw.
 

jaystcb

Sy 0902, 92Ty 0909
Re: PLX O2 sensor location

I went the cheep way and put the o2 sensor in the stock location. I just had to hook up an extra wire to the ECU.
 
Top