Quick ignition advance question

JayLo

Sir Boost-a-Lot
Under full boost (15.5psi) Datamaster reads the following:

Spark Adv Base Degrees - 10.5
Spark Retard Degrees - 10.5
Spark AdvanceDegrees - 0.0

Does this mean total timing is really 0 degrees or does it mean it is 0 degrees plus the 10 degrees at the distributor?

I ran a 13.56 under these conditions. What is normal Spark advance for a Syclone in proper tune? I've heard it should be 10. Is there any truth to that?

Thanks for the help.
________
Kishakiss live
 
Last edited:

dgoodhue

BuSTeD 4.3
Re: Quick ignition advance question

It probably retarding the timing 10.5 degrees, so you are running 0 degrees. What chip are you using and if applicable what setting, boost control?

Full timing on stock chip and ultimate is at WOT and higher RPM is 13.7-14.0 degrees.
 

JayLo

Sir Boost-a-Lot
Re: Quick ignition advance question

Thanks for the info.

I have the stock chip (early revision as my truck is #525).

I am using a manual boost controller (ball and spring). Though I have the cat removed, boost is rock solid at 15.5psi. I'll use this info for MegaSquirt tuning. Now that I have my ignition bugs worked out, I need to know how far I can go with timing up top. This knocksensor and all the flase knock it is picking up is driving my nuts.

Man, I wonder how much quicker I would have run at the track with 13.7-14.0 degrees more timing up top.
icon_wink.gif

________
Buy marijuana seeds
 
Last edited:

JayLo

Sir Boost-a-Lot
Re: Quick ignition advance question

What do you guys think of these?





Both were at interstate speeds this morning (maybe 3500rpm max). Truck was warm. Air was very cool. 92octane gas. AFRs are normal (probably richer than they should be at 11.5:1)
________
Wiki vaporizer
 
Last edited:

dgoodhue

BuSTeD 4.3
Re: Quick ignition advance question

JayLo said:
I am using a manual boost controller (ball and spring). Though I have the cat removed, boost is rock solid at 15.5psi.

This knocksensor and all the flase knock it is picking up is driving my nuts.

I am a little confused, it this using the stock ecm or the MS. Are you using a 2 bar or 3 bar map?

Through in some race gas (enough to raise the octane significantly) in and make sure its not real knock.
 

JayLo

Sir Boost-a-Lot
Re: Quick ignition advance question

These runs are with the stock PCM (2-bar). I only switched back to try and figure out what the timing from the factory under full boost was.

I've recorded similar data with a 100 octane/Torco blend.
________
Live Sex
 
Last edited:

dgoodhue

BuSTeD 4.3
Re: Quick ignition advance question

JayLo said:
These runs are with the stock PCM (2-bar). I only switched back to try and figure out what the timing from the factory under full boost was.

I've recorded similar data with a 100 octane/Torco blend.

I wouldn't call your boost rock solid then, the MAP sensor is maxed out. The 15+ psi reading means it just is maxed out and is inaccurate even if it doesn seem to move around 15.2-15.3psi.

The 10.5 degree of total timing is probably an overboost value. The ECM also won't retard beyond 0 degree of total timing. I can see from your first chart that the knock retard has hit 12.6 the stock value maximum value. I have also found out the hard way that the ECM doesn't pull timing past 0 degree so if you running 10.5 degree of timing and the ECM pulls 12.6 of knock retard it only pull 10.5.
 

JayLo

Sir Boost-a-Lot
Re: Quick ignition advance question

I figured as much with regard to not being able to pull more timing than 10.5 up top. Even if Spark Adv Base Degrees < Spark Retard Degrees, Spark Advance Degrees is still equal to 0.0 at its lowest. At least that's what my DM log shows all the time.

Per the boost reading, yes the MAP is maxed out at 14.5psig. I should have mentioned that I was watching my boost guage (a Stewart Warner, not the crappy stock one) during these runs and it is very stable up top. I've also logged it on MegaSquirt (2.5 Bar MAP) which registers a very stable 15.5psi as well.

What you are saying regarding overboost timing is new information to me.

So if I Grainer it down to say, 14psi, my total timing would ideally be 13.7-14.0 degrees total advance up top?

Thanks for all of your input.
________
SexyLexa
 
Last edited:

dgoodhue

BuSTeD 4.3
Re: Quick ignition advance question

This table is from the Chitown Chipping page, I found on Huryde 'old' website. They have a 2bar map on that site but it defiantely isn't the stock chip, because it has way too much timing. Anyways this is a 3 bar timing table, its probably the T1-15. The 200 on the top is 14.5psi, this might be helpful in a place to start.

chip_t1.jpg
 

JayLo

Sir Boost-a-Lot
Re: Quick ignition advance question

dgoodhue said:
This table is from the Chitown Chipping page, I found on Huryde 'old' website. They have a 2bar map on that site but it defiantely isn't the stock chip, because it has way too much timing. Anyways this is a 3 bar timing table, its probably the T1-15. The 200 on the top is 14.5psi, this might be helpful in a place to start.

chip_t1.jpg

Great info and link. That will be a big help. Thanks again. :tup:
________
Sweet_Nansy live
 
Last edited:

turbodig

Active member
Re: Quick ignition advance question

JayLo said:
Under full boost (15.5psi) Datamaster reads the following:

Spark Adv Base Degrees - 10.5
Spark Retard Degrees - 10.5
Spark AdvanceDegrees - 0.0

Does this mean total timing is really 0 degrees or does it mean it is 0 degrees plus the 10 degrees at the distributor?

I ran a 13.56 under these conditions. What is normal Spark advance for a Syclone in proper tune? I've heard it should be 10. Is there any truth to that?

Thanks for the help.

That's precisely what it means. If the spark tables are calling for 10 degrees of advance, and ESC is pulling 10 of it out, you have a net of 0.

This is assuming, of course, that you have your static timing (with the brown wire unplugged) set to 0 degrees. Any advance you have here should be added to the above net figure.

It's really pointless to manually advance a dissy, unless you're running in a class that only allows a stock chip, and you have good gas in the tank. The knock sensor will actually take more timing away than you would need to to get rid of the knock.

How much timing you should start with depends greatly on the type of gas you're running, and the quality of that gas. Also, it depends greatly on how much fuel you're delivering,
if you're running pump gas.

I've done cheap gas chips that run 8-10 deg, plain 92 chips that run as much as 14, 93-94 octane chips that were up to 17-18. Full race 116 chips that were in the 27-28 deg area.

Note that the above are *not* rules-of-thumb. Each truck wants what it wants, don't take somebody else's specs and expect them to be ok.

Start low... say, 8-9 degrees. If you're nervous, put a couple gallons of xylene in the tank to ward off evil spirits. Then slowly crank the timing up, watching your fueling and knock as
you do. Street gas must be much richer than race gas, typically in the low 11:1 area... additional fuel will allow you to run more timing without knock.

Realize that timing needs will change with different boost levels, and with the temp and humidity of the day. Also, altitude.

Timing will change what your wide-band reads, but it won't change AFR significantly. Ie, your AFR will read .2-.5 lambda less due to a timing change, but your fuel tables or boost didn't change. (Therefore, your Air/Fuel ratio couldn't have changed)

Daily driver chips should be pessimistic... if your truck likes 12 degrees and doesn't seem to knock, set it to 9 degrees. Your motor will live longer.

There is a point where more timing is no longer a good thing... the Max Brake Torque point. (MBT) Most of our cals are nowhere near MBT, but some of the bigger race cals can get there. Where this point is depends on your heads, manifold, quench area, piston dome, etc. etc.

Bottom line, though, is start low and stay timid on street gas.

Later,
 

JayLo

Sir Boost-a-Lot
Re: Quick ignition advance question

Thanks for the input. You guys have been a HUGE help.

I tried a few WOT runs tonight after my buddy Scott (the MegaSquirt guru) built up the fuel tables as I drove. Blessed with cool weather, the truck seems very happy at 10? up top at 15.5psig.

We are flying blind with regard to the knock sensor for now (I've replaced it, but it still hears all sorts of false knock so it is disabled in MS for now) so I want to be very safe. My ultimate goal is to have a knock free tune but still have a fully functional knock sensor just in case.

I do need a TON more timing down low as this thing is a slug out of the hole compared the the stock PCM. I think I'll use my DM logged data and build the bottom part of the table off of that.
________
Depakote Settlement Information
 
Last edited:
Top