Tuners please help

Peter

my Ty and me 25+ years
Re: Tuners please help

For what its worth, I wanted fuel table F29x to control the AFR without confusion from PE. With PE map threshold set at 100kPa, for instance, there was a step change offset (lower) in the fuel map. I disabled PE by setting the threshold (KPEMAP3) to 299kPa and the drop went away. Now I get reproducible boost AFR's for a given cell. I know this may be heresy, but it works for me.
 

Peter

my Ty and me 25+ years
Re: Tuners please help

Typically the PE MAP threshold is set around 100kPa, Mild accel might be considered below 100. I hit 100kPa at about 30% throttle. Below 100 i'm shooting for 14.7 afr (except at idle) and I'm not seeing any lean spikes, so it is possible. I tuned mine exclusively with a custom version of Autotune that only looks at steady or increasing throttle and/or speed. The result is pretty accurate AFR's under those conditions. Part throttle response seems fine. Unfortunately this method is not any good for trailing throttle, where I still have an occasionaly roughness. I mentioned disabling PE because I personally found it confusing to work with. To me, it is easier to just set your target afr, including boost, using F29x.
 

TYTILIDIE

METH HEAD
Re: Tuners please help

For that its more about the adjacent cells, not the cell your on...as far as my understanding goes your never on just 1 cell, but 4 at a time. It interpolates the data and comes up with an average based on a percentage of each adjacent cell. try messing a bit with the cells directly adjacent to where you are. Just an idea, but I've had that happen, I notice it most with a loopy idle. it will be kinda rich and idle up, then hit a leaner cell and bog back down, then loop.

I've been doing this what, 5 years now? I know to look at surrounding cells. I have had this problem pretty much since day one. I opened my first bin up and looked at the trouble area and found that I ended up making a huge VE spike to try and compensate and it never did. With that said, I may try Peters idea and see what happens. In cruise, no pedal movement, my VE is about 95% close to perfect. That light acceleration is what is getting me. Hell, even if I smash the pedal, it might go lean for a split second but enough you can feel the hesitation.
 

BMFB

Not to scale
Re: Tuners please help

didn't mean to underestimate you, your experiance, or your tuning prowess, just throwing that out there. I have the same issue on my buddys prelude I'm tuning, But it turns out he had a pretty big exhaust leak befor ehis o2 that he didnt know about before i tried tuning it, so i gotta go back and try again.

The ty was like that when I first started tuning it the first time, but it seems like when I was done tuning it I didnt't but I had a whicked looking fueling table that had 2 BIG jagged canyons with the rocky montains in between them, nothing like the smooth as glass tables I see from others, but it ran great. I just rebuilt the motor, and I have to retune it, so i'm in the same boat with you guys again, and hell, I prolly had it wrong, and just don't remember. I'll keep on this thread, and see if I have the same issues in the coming days.
 

wildphil

I Love My Ty's
Re: Tuners please help

Drove the truck a little today. No lean spots. Rob didn't tell me the adjustments he made to the bin. I could tell he smoothed the cells out. I'm sure he will post and let us know.

I ran autotune after one log and its trying to put the valley back in again. So I smoothed it out again. Is there a time were you stop using autotune and just manually adjust the cells?

Just did one log. The fuse blew again on my new Flex-A-Lite fan. Something is going on there. But I am going to make another post about that.
 
Last edited:

turbodig

Active member
Re: Tuners please help

Drove the truck a little today. No lean spots. Rob didn't tell me the adjustments he made to the bin. I could tell he smoothed the cells out. I'm sure he will post and let us know.

I ran autotune after one log and its trying to put the valley back in again. So I smoothed it out again. Is there a time were you stop using autotune and just manually adjust the cells?

Just did one log. The fuse blew again on my new Flex-A-Lite fan. Something is going on there. But I am going to make another post about that.


One common thing I see here, is that the people struggling are looking for AFRs to be some number.

We beat this to death, I know, but give the motor what it wants- don't pay so much attention to what the AFR numbers are in the transitional cells. Closed loop trim brings the AFR into line over longer periods, which is what's really affecting fuel consumption.

Phil, I think you're past the autotune point... it's a good thing to get you started, but it, too, is too fixated on AFR numbers. Do some basic pull-aways, and watch where the bubble goes. Bump fuel up just past the point where the stumble goes away. You'll start to see common threads if you watch the bubble long enough.

There really needs to be a "lesser PE" that handles the tip-in cases. In pure theory, this shouldn't be necessary, but the quirks in the fuel algorithm cause some things to happen that wouldn't if we had a truly accurate Speed-Density equation. The PE that we have isn't much- I can understand where Peter is coming from with the PE disable.

I suspect what Rob did was bump the 50-60-70 kpa cells up in off-idle RPMs.

A good exercise to learn what the system is doing- Have somebody else drive, and watch the bubble. Don't change anything, just watch where the bubble goes in the VE table as the driver does pull-aways, passes, roll-ups to stop. You'll see places where AFR goes wacky-lean, despite the fact that those cells are pretty close in steady-state operation.
 

BMFB

Not to scale
Re: Tuners please help

I must have an older version of tunerpro, or Im ignorant as how to watch the bubbkle
 

JSM

Active member
Re: Tuners please help

Autotune was built basically to give new tuners the confidence to get started. As dig said at some point you have to graduate to the big boy section at the toy store. No more pull-ups.

Where the truck feels good will always over rule an AFR guage.

pullup.jpg
 

WyoSyclone

Active member
Re: Tuners please help

When modifying Phil's BIN I stayed strictly in f29x. I reviewed a lot of other tables to make sure nothing else looked out of whack. Satisfied that all was OK for now, I just looked at the log and identified spots that were obviously a problem.

I take a log sheet and make 3 columns - rpm, kpa, and afr. I look through the log, identify problem spots (making sure that TPS has settled at a relatively constant value). I then go into f29x and modify those problem cells only. After I have moved just those problem cells I then look at the overall graph and identify peaks or values that look suspect. I repeated this process probablyl 30 times with my Sy until the drivability was 95% perfect. I then went back to problem areas and played with AE, and other tables, until I was happy.

One just has to learn the program and what the variables affect and keep a large dose of patience handy!
 

wildphil

I Love My Ty's
Re: Tuners please help

When modifying Phil's BIN I stayed strictly in f29x. I reviewed a lot of other tables to make sure nothing else looked out of whack. Satisfied that all was OK for now, I just looked at the log and identified spots that were obviously a problem.

I take a log sheet and make 3 columns - rpm, kpa, and afr. I look through the log, identify problem spots (making sure that TPS has settled at a relatively constant value). I then go into f29x and modify those problem cells only. After I have moved just those problem cells I then look at the overall graph and identify peaks or values that look suspect. I repeated this process probablyl 30 times with my Sy until the drivability was 95% perfect. I then went back to problem areas and played with AE, and other tables, until I was happy.

One just has to learn the program and what the variables affect and keep a large dose of patience handy!

I want to thank you for helping me. I sure can tell it is running better. When I get my cooling fan straighteded out I will run some logs and send you so you can see the difference.
 

wildphil

I Love My Ty's
Re: Tuners please help

I am getting all kinds of good info from all of you.

I'm slow at learning tuning. Thanks for everyones help.

One day I want to set down with someone that knows this this stuff for a little training.

I am hoping to graduate to the big boy section of tuning one day.
 

WyoSyclone

Active member
Re: Tuners please help

I want to thank you for helping me. I sure can tell it is running better. When I get my cooling fan straighteded out I will run some logs and send you so you can see the difference.

Yup, let's keep working on it Phil :D It will take a few more logs to get it dialed in.
 
Top