Search results

  1. tbauer03

    Holley Dominator Fuel Prime

    Re: Holley Dominator Fuel Prime I used the two ign fuse locations in the cab to power the dominator red/white wire and the holley digital dash. Is there another good source to tap into for switched power?
  2. tbauer03

    Holley Dominator Fuel Prime

    Re: Holley Dominator Fuel Prime Thanks for the help I dug my old fuel pump relay out of storage. Just want to make sure i hook it all up ok because the factory harness is no longer intact. I gather that the green/white wire is the trigger which will connect to the holley green wire. The gray...
  3. tbauer03

    Holley Dominator Fuel Prime

    Re: Holley Dominator Fuel Prime Thanks for the help I removed all the relays when I took out the wiring harness. I still have them I'll just have to rewire them.
  4. tbauer03

    Holley Dominator Fuel Prime

    Its been months since I had to stop this Holley Dominator install because I have been relocating. But when I last touched it I was finishing up the wiring and starting with the software. Couldn't get the fuel pump to prime and I left it at that. Today I knocked the dust off and put a voltmeter...
  5. tbauer03

    Garage Sale OEM and Aftermarket

    Re: Garage Sale OEM and Aftermarket I have updated the posting. Added a few items and deleted what has sold. - Bump
  6. tbauer03

    Garage Sale OEM and Aftermarket

    Re: Garage Sale OEM and Aftermarket No full description is in the picture. The chip can be reprogrammed but I am not sure what that would entail. This is for a 50# injectors 422 cam vortec heads built motor. Switched for pump gas or alky.
  7. tbauer03

    Garage Sale OEM and Aftermarket

    Re: Garage Sale OEM and Aftermarket Yes it is for a typhoon. It is a stock dynotech shaft. At some point It has been painted an aluminum color. I bought it used in 2003 and I have put about 20,000 miles on it. I was told it was from a low mileage truck when I bought it for whatever that is...
  8. tbauer03

    Garage Sale OEM and Aftermarket

    Getting settled into a new garage and I could use some more space. I will pay for shipping if its less than $10 but anything over that buyer will help. --------------------------------------------------------------------------------------------------------------------------------- Refinished...
  9. tbauer03

    Holley HP install and tips

    Re: Holley HP install and tips Ok so your not actually locking the distributor down until you hit the 25 degree idle/ cranking timing. The 15 w/o fuel is just more of a safety precaution to not cause early detonation because you might have the dist way out of whack. Is that the correct way of...
  10. tbauer03

    Holley HP install and tips

    Re: Holley HP install and tips I am still confused. :dunno: I must be over complicating this in my head. So just set to 25 degrees running with out fuel and confirm when its idling? What is your reference angle? Top corner of this screen shot. And if you don't mind could you please e-mail...
  11. tbauer03

    Holley HP install and tips

    Re: Holley HP install and tips Did you set the timing to 25 degrees? Or is that what it is with the computer controlling things? I don't believe my my timing tab off the timing chain cover reads that high. If I wasn't clear I am running a new motor and have to get the distributor dialed back...
  12. tbauer03

    Holley HP install and tips

    Re: Holley HP install and tips I am getting pretty close to having everything mechanically/electrically installed to get the truck running. Minus a couple optional input/output things I can do later. But I'd like to get this truck fired up so I can move it around. I am starting to wrap my...
  13. tbauer03

    Holley efi mounting pics????? Where it fits???

    Re: Holley efi mounting pics????? Where it fits??? I cleaned up the wires a bit. All the excess wires and relays tuck behind the ecm really well and from any normal vantage point you can't see anything.
  14. tbauer03

    Holley efi mounting pics????? Where it fits???

    Re: Holley efi mounting pics????? Where it fits??? I am not finished yet but I put it behind the dash where the original cpu was. It sticks out a little bit due to the length but you don't see it unless you stick your head down there. Maybe not the best spot but I think it will work.
  15. tbauer03

    WTB heat sheilds for ex manifolds

    Re: WTB heat sheilds for ex manifolds you can still get the single loop from your gm dealer. The double loops they also stock but they do not fit right. I also have a few extra of the heat shield but maybe not all of them so. if sport machines falls through let me know
  16. tbauer03

    NE FS: 4 bolt main engine block

    Re: FS: 4 bolt main engine block This was the old block I pulled out over a year ago. It's just been sitting around ever since and I'll be moving soon so I figured I'd see if anyone wants it because it might still be worth using.but If not I'll try converting it into a table for my man cave...
  17. tbauer03

    NE FS: 4 bolt main engine block

    This is my last engine block. Detonation killed the bearings and metal was ran through it. It is currently 30 over, my machine shop said it should be fine at 40 over but I elected to go with a different block and we never sonic tested this block. It has been drilled and tapped for pro gram 4...
  18. tbauer03

    Holley HP install and tips

    Re: Holley HP install and tips Yes
  19. tbauer03

    Holley HP install and tips

    Re: Holley HP install and tips Does anyone have the fuel injector wiring harness diagram? I want to make sure I have cylinder 1 and 3 correctly wired. Their labels were never attached when I opened the box and I seem to have misplaced the wiring diagram. I currently have black/red to cylinder 1...
  20. tbauer03

    Holley HP install and tips

    Re: Holley HP install and tips OK so then you didn't use the fuel pressure pigtatil off the main harness. I am running a 4l60e not a 700R4 and the vss plugs into the dominator as an input. Wouldn't i need to set up an output from the holley to the drac to then move the speedometer?
Top