Search results

  1. tbauer03

    Holley HP install and tips

    Re: Holley HP install and tips What are you doing with fuel pressure? I have had an electric auto meter pillar gauge tapped into the fuel rail. I can just plug the holley right into this and be good. Its the same 3 pin connector. But would I be able to still use the pillar gauge by using an...
  2. tbauer03

    Pro-gram Main Caps

    Re: Pro-gram Main Caps I have howards as well. Just be aware that the sides are wider than the programs and you will have to modify your dipstick.
  3. tbauer03

    Engine oil priming???

    Re: Engine oil priming??? Should the oil flow onto the rocker or squirt out. Sometimes I get a squirt but mostly just light flow. I am guessing it depends on where the cam shaft is on the lift sequence but I just want to know what I am looking for. The squirts tend to happen when i first pump...
  4. tbauer03

    Turbo Flange Nut

    I seem to have lost one of the nuts that hold the turbo onto the exhaust manifold. The local home depot only sells the m10 x 1.5 nuts with standard 17mm heads and that is too big for the exhaust housing. I need the 15mm JIS head but the only place i can find them is on the internet and after...
  5. tbauer03

    Holley knock sensor calibration question

    Re: Holley knock sensor calibration question the motor is out of the car, physically swapping it out isn't an issue if it allows me to closely replicate your settings.
  6. tbauer03

    Holley knock sensor calibration question

    Re: Holley knock sensor calibration question So will both GM Part No. 10456549 and GM 10456288 work? I currently have 10456549 on the truck should I swap it out?
  7. tbauer03

    Engine Install Tips?

    I am getting very close to putting the motor back into the engine bay. This will be the first time I have put the motor back in with the transmission already installed. I am assuming if I jack the transmission up to the top of the tunnel I'll be able to get the dowels lined up and then drop it...
  8. tbauer03

    Mickey Thompson ET street SS tires

    Re: Mickey Thompson ET street SS tires I bought a set but haven't even mounted them. But I was told they hook very well and I personally like the tread pattern best out of available 16" drag radials.
  9. tbauer03

    WTB C Shaped Exhaust Manifold Bolt Locks

    Re: WTB C Shaped Exhaust Manifold Bolt Locks Thanks
  10. tbauer03

    Oil dipstick hits main caps

    Re: Oil dipstick hits main caps Ok I'll lube it up with some grease and go at it another day. I have a hole tapped into the heads where the bracket was lining up and it had me confused. But I am sure the tube will flex enough at the top end to get back to that tapped hole.
  11. tbauer03

    Oil dipstick hits main caps

    Re: Oil dipstick hits main caps I believe I got it to work. But I have one question. Is the dipstick tube not supposed to set all the way onto the block? Mine tappers and wedges in with about a 1/4" to go. As a result my cut on the tube was about 1/4" shorter than what I wanted. But I ran the...
  12. tbauer03

    WTB C Shaped Exhaust Manifold Bolt Locks

    I have pm'd Renz and Sportmachines but haven't heard back from them. Anyone else have a source for these?
  13. tbauer03

    Oil dipstick hits main caps

    Re: Oil dipstick hits main caps Yeah the engine builder took care of the drain hole and clearacing the rod bolts. Did you bend the tube so it went to the right of the cap as viewed in the picture? Or bend it so it contoured over the cap? Does going right interfere with the rotating assembly?
  14. tbauer03

    Oil dipstick hits main caps

    Re: Oil dipstick hits main caps I took the pan off and snapped pictures.The howard caps are a lot beefier than my old pro gram caps. There is about a 1/4" extra towards the dipstick. I don't have a tube bender but I may have to clearance the pan a little bit as well to gain the clearance...
  15. tbauer03

    Oil dipstick hits main caps

    Re: Oil dipstick hits main caps I couldn't even get the flexible dipstick in there much less the tube
  16. tbauer03

    Oil dipstick hits main caps

    I just got my engine back from the builder and started putting on stuff like the exhaust motor mounts etc when I realized the oil dipstick tube hit a main cap. I should have thought of this before and gave the builder the tube to work around but I didn't. Anyway I have read people had to notch...
  17. tbauer03

    Midwest meet nats weekend

    Re: Midwest meet nats weekend Interested but I can't commit yet
  18. tbauer03

    CANCELLED - 2016 SyTy Nationals

    Re: CANCELLED - 2016 SyTy Nationals Well I am dissapointed but I understand. Sad day.
  19. tbauer03

    WTB pass side PCV T

    Re: WTB pass side PCV T bump
  20. tbauer03

    Registration is OPEN!

    Re: Registration is OPEN! Done
Top