Engine Rebuild / Recipe

bezerk

New member
will wait on the price you give me for the pulley.

Than i probberbly gonna do, what is should do.......
Alright?
 

TurboManiacal

Donating Member
bezerk said:
will wait on the price you give me for the pulley.

Than i probberbly gonna do, what is should do.......
Alright?

Next step is to order the parts rene. Have you hot tanked your block yet? Have you bored it out yet .030 over?

Gather up your good crank and gather your money. Are you going to Hockenheim with Andre on 20 Sept? It would be a good idea.

I'll need approximately $2700 in cash to order parts. Yes, that'll be dollars not euro.

Have you gone ahead and fixed your starter purple wire while the engine is out?

Have you flushed your radiator and oil cooler?

What are other MUST do things that Rene needs to get done now?
 

nightdiver

Active member
I flushed my oil cooler 5 years ago,and cut it cause i wanted to see inside
After 20 minutes of cleaning the oil cooler was full of mettal parts inside and filter paper.Use your old oil cooler and youre gonna spend money AGAIN...been there,done that
 

bezerk

New member
What should be the best and cheapest way for the oil-cooler??? anny thoughts?
i know Nightdiver did a external oil-cooler, i think this is gonna be the best and cheapest solution.

About the engine Bore i think i need the measurements of the pistons and the clearance they need, so they can do it in one step.(boring)
They also gonna do the drilling of the 4boltmain caps, (they have a better machine than i have).

What do you mean by hot-tanking the block??

haven''t heard from andre in quite a while. But is there something nice going on in HockenHeim?

they gonna stamp the pistons and rods while balancing wright? don''t want to mix that up.
About the purple wire, it has been on my mind , gonna do that.

Order the parts, and let the Dollar go low!!!. :wink:
1€ = $1,15 anny speculations about the ratings?


Could Hood throw in some of those measuringstokes for the main and rod bearings?

If Ryan and i are gonna do the engine together we need some hints on paper i geuss, or some phone numbers.

Thanks everybody who helped me so far


And Ryan, this time you stay sober! we must think :drinking:
 

myclone

Donating Member
bezerk said:
What do you mean by hot-tanking the block??

This is just a process that a machine shop does to clean the block. Once the bare engine block is machined (boring the cylinders in your situation) the block is placed in a pressure washing device that floods the block with hot cleaning solution to remove all of the debri. Its basically an over sized version of a clothes washing machine designed for engine components (blocks, heads, cranks, etc).

Before these high tech machines were available the parts were submerged in a tank or vat of VERY hot cleaning solution for a period of time and then removed so the operator could rinse the cleaning solution/debri off. Thats where the name "hot tanking" or "vatting" came from and the term is still used today even though the process doesnt involve tanks or vats of cleaning solution anymore.

Any machine shop that can perform a bore job should be able to hot tank your parts for a small fee ($20-$50 here in the US).

HTH
 

bezerk

New member
Anny thoughts about the oil-cooler?

And throw me in an Auto meter Phantom gauge 2 5/8" oil-pressuere Mechanical <= Goood?? or electrical is better easier to wire??
 

myclone

Donating Member
bezerk said:
Anny thoughts about the oil-cooler?

My thoughts are that the stock oil cooler is fine for daily driving and drag racing with short cool down periods between rounds. However, IMO if you spend extended periods of time at WOT (or close to it) you may want to add an extra cooler into the circuit. Just my opinion though.

And throw me in an Auto meter Phantom gauge 2 5/8" oil-pressuere Mechanical <= Goood?? or electrical is better easier to wire??

This is more of a personal preference IMO. I like mechanical gauges over electrical myself but the electrical gauges are definately easier/less hasssle to install IMO.
 

sytyguy

Moderated User
nightdiver said:
Sigo said:
??????????????

The question from Rene about the oil cooler never got answered, so Ryan replied with a "bump" to get the topic moved to the top and hopefully strike someone's attention. And it worked. :wink:

Michael
 

bezerk

New member
don''t know who is taking care for the balancing, polishing of the crank.
But they need the harmonic damper right?
how is that going to be?

so with the 4bolt maincaps (should it be save with normal 4bolt, or do i get splayed?) i need line bore, so wich seize of bearings do i get?

with the camshaft bearings, just install them, or should they be installed and than be reseized to the specifications of the cam?
 

sytyguy

Moderated User
Anytime you change pistons, rods, etc....you need to have the rotating assembly rebalanced. If you were just re-ringing the engine, then you could slap it back together w/o rebalancing and be fine, but not in this case (I wouldn't chance it). They will need your balancer and flywheel to balance the rotating assembly.

When the machinist line bores the main caps, you'll wanna run whatever main bearings the crank is cut for. Same for rod bearings.

Cam bearings are one size (usually) and are not sized per camshaft.

HTHs and Myclone........correct me if I'm wrong on anything. :D

Hood
 

myclone

Donating Member
bezerk said:
don''t know who is taking care for the balancing, polishing of the crank.
But they need the harmonic damper right?
how is that going to be?

Yes, the machine shop will need the harmonic damper you intend to use. All thats required of you is to supply the harmonic damper, crank shaft, flex plate, pistons, and rods for them to balance the rotating assembly.


so with the 4bolt maincaps (should it be save with normal 4bolt, or do i get splayed?)
IMO if you are going to spend the money for a 4 bolt conversion then it would be best to pay a little extra for the splayed versions. Non splayed are easier for a machinist to install but the piece of mind would warrant the extra cost IMO to step up to the splayed mains.

i need line bore, so wich seize of bearings do i get?

The bearing size will end up being as factory as far as the line bore is concerned. The different sized bearings will come into play depending on wheather or not the crank shaft you use is ground undersize. Basically you will need main bearings for a 4.3 V6 but your machinist will be able to determine what, if any, undersized main bearings you will need by measuring the crank shaft. To summerize the above you need main bearings for a 4.3 block but the correct thickness according to how much, if any, the crank is ground.

with the camshaft bearings, just install them, or should they be installed and than be reseized to the specifications of the cam?

Cam bearings do not need to be resized under normal circumstances. They are simply installed by the machinist in the proper orientation to align the oil supply holes in the block with the oil supply holes in the bearing. No other work is needed here. This is assuming that the cam bearing bore in the block wasnt damaged in any way which happens but is extemely rare.

HTH
 

myclone

Donating Member
sytyguy said:
Anytime you change pistons, rods, etc....you need to have the rotating assembly rebalanced. If you were just re-ringing the engine, then you could slap it back together w/o rebalancing and be fine, but not in this case (I wouldn't chance it). They will need your balancer and flywheel to balance the rotating assembly.

When the machinist line bores the main caps, you'll wanna run whatever main bearings the crank is cut for. Same for rod bearings.

Cam bearings are one size (usually) and are not sized per camshaft.

HTHs and Myclone........correct me if I'm wrong on anything. :D

Hood

IMO you covered it just fine cept you did it with a WHOLE lot less typing than me. :lol: I wish I could master that "keep it short and to the point" thing :oops: .
 

nightdiver

Active member
The Captain knows what to do... :D
Rene has a photo from my oil cooler under the radiator...its a normal big oil cooler
 

bezerk

New member
i will do most of the work myselve, except the linebore, balancing cilinder bore.

Ryan told me that somebody is willing to trade me a crankshaft so that the work is done in the US, i will sent my old one back.
So maybe that person also could trade his damper, that would be great.

otherwise i found a workshop in the netherlands that can do the job aslo.

http://www.dymotrack.nl <= english site

So throw me in the splayed 4bolts
and don''t forget the new-oilpump
i think the part list is complete, so i don''t get stuck while assambling, because i forgot to order the parts.

Thank you all so much!
 

myclone

Donating Member
bezerk said:
Ryan told me that somebody is willing to trade me a crankshaft so that the work is done in the US, i will sent my old one back.
So maybe that person also could trade his damper, that would be great.

Rene,

Im not trying to tell you what to do here or be the know all/end all of engine work but Id like to make sure you are clear on some details.

Getting a crank shaft from someone is no big deal as long as its of the correct finish on the bearing journals. However, since you are installing the crank into an engine which will have new pistons (and rods?) it will need to be balanced no matter if they supply you with a damper, you buy a new one, or reuse your old one. I think you are planning on balancing anyway but I wanted to make sure you are clear on that fact. Basically if you change any major component in the roatating assembly it needs to be balanced.

I dont know who is supplying your cranshaft but it would prolly be easier to have them supply you with the correct bearings for it. Thats assuming the crank has been reground or what have you. If it is a used and/or untouched crank shaft then you will need to measure the journals and purchase bearings according to what the journals measure out to be.
 

bezerk

New member
Yeah, i know that it must be rebalanced, and i wanted to let them do it in the US, so they can also supply me the right bearings,

work on crank:
nitrid
ported
balanced.

maybe i should skip this part and let them do it in the netherlands, and they must give me the right bearings (probberbly another brand).

but lets hope Ryan comes here to explain
 
Top